Big Z

He Frank, happy birthday! hope everything is ok with you. maybe we could meet each other again soon. i'm looking forward to see te 280zxrsct. Rick

Hi Frank, It's not a story or a rumour, i'ts also not a Nismo item. I think that it was done by the owner of the s130, and I do have some pictures Enjoy! So Frank, time to get the Dremel and get back to work again P.s. Frank, the 240z turbo is now up and running with B&W T5, turbo cv swap and turbo 3.36 diff See you soon. Rick

That is going to be next year during the summer, so i have some time to tweek my little Z. Ps wait till i put my collected goodies on my car

He Frank, Looking good on the paint job, nice cage and car. Are you going to put the zxr decals on the car (if you have them)? Looks like everything is comming together Good luck with the paint, Rick

Thanks, i was hoping it wil work. I have with the stock turbo on the engine with the .82 ar house in 4th gear 10 psi @ 2700rpm so it spools good, it wil give 7 psi @ 2500rpm ( i have a 3''dp and its helps). I have a look at the exhaustwheel and hope it fits.

Hi GrommitZ, Yes after searching for SleeperZ i have found the tread about the t04b and read it, thanks for the tip , like you sayed the exhaust house is to small and i'm not gonna use it. With the stage 3 wheel you pointing at the exhaust side? with a .63 ar, the stock exhaust side is .82 ar. When i search on the net about the compressor wheel spec, i found it is good for 450 to 480 crank hp so i was thinking it's a good turbo. is there no way to just bolt the turbo inside the stock exhaust house? Thanks for your reaction rick

Does anyone have some infomation about this turbo? I'm kinda stuck concerning if its useful for my setup, my goal is 350 rwhp. I know that there are some turbo experts around here

Hello, I just got a good deal on a used but rebuild Garrett T04 (i think turbo from a guy who used it on a Toyota AE86. The house says t04 ar 60 and it is 5.91 inch (15 cm) diameter, the exhaust house hase a .36 AR for spooling on a 1600 CC engine. The compressorwheel top size is 2.17 inch (5.5 cm) and bottom size 2.76 inch (7.0 cm), when i calculate the trim i get 61.73 trim. The exhaustwheel top size is 1.81 inch (4.6 cm) and bottom size 2.52 inch (6.4 cm). My question to the people who run t3/t4, what kind of turbo is this and what kind of power does this turbo make. I did used the search function and i think it's maybe a t04b v1 or v2? My ohter question, is the exhaustwheel the same like the stock t3 size and would it fit inside the .82 ar (european size) house? I have some pictures i will post below thanks Rick

Frank280zx, i'll be there today with the speedo:) so prepare yourself

Hi Evildky, what do you think about the 3.54 R200 from the zxt car? Its an open diff, then i can also upgrade to rear disc brakes and cv joints from the turbo with the stub axles?

Frank, I think with a good setup and a lite body you can kick some **s of scoobys evo's and Audi S2 look at Garrett76zt and what Thumper did. I'm also looking to put a type of water methanol injecton on the engine. I do like to take it around a track but there are only a few days in a year the track is open for private cars! And autox is not my type of racing, i like to pay 5 euro and do some 1/4 mile runs and talk about the car.