Jump to content
HybridZ

78 RB26 260Z


Recommended Posts

I'm still planning on sticking an RB26 in this so thought a build thread would be a good idea. The first few posts are just copied:

 

 

 

 

 

Just bought my first Datsun and I'm really happy with it so thought I'd post some photos. I've still got loads to learn about these cars so I'm sure this forum will be a huge help.



1979 Datsun 260Z


Shes in great condition, only 28480 miles on her when I bought it although its not far of 29k now. She was built in 1978 but only first registered in 1979 and going by the chassis number she was one of the the last to be imported from Japan to the UK. Theres few photos with my Civic in them also, shes a 1991 Civic running a 243hp B20.


It drives beautifully, its had new bushes all round and with the low miles on the chassis it still feels really tight so its a joy to drive.



DSCF8277.jpg



I have real big plans for her involving seam welding, cageing, hugely uprated suspension and brakes and an engine swap, I like the idea of a V10 because I love them but failing that I'd like an RB26DETT.

For now though the first mods will be:

Paint the brake calipers and drums
Polish up the lips on the wheels
Give the engine bay a good clean
Clean out the carbs
Do something with the rocker cover
Give her a full detail, I've already done the inside but the outside still needs done


After that lot I'll be fitting a bigger better airdam and a rear spoiler follwed by a good coilover setup with adjustable camber plates welded in as shes definitly too high at the moment. Then I'll have to fit the arch flares before I can fit my new wheels other wise they won't fit.





Photos

Sorry for the amount but I couldn't decide which to put up.



DSCF8275-1.jpg



DSCF8264-1.jpg



DSCF8327.jpg



DSCF8239.jpg



DSCF8241.jpg



DSCF8242.jpg



DSCF8255.jpg



DSCF8259.jpg



DSCF8306.jpg



DSCF8262.jpg



DSCF8325.jpg



DSCF8236-1.jpg



DSCF8249.jpg



DSCF8250.jpg



DSCF8334.jpg



DSCF8288.jpg



DSCF8300.jpg



DSCF8286.jpg



DSCF8294.jpg



DSCF8258.jpg



DSCF8280.jpg



DSCF8260.jpg



DSCF8247.jpg



DSCF8248.jpg



DSCF8245.jpg



DSCF8253.jpg



DSCF8252.jpg



DSCF8305.jpg



DSCF8316.jpg



DSCF8314.jpg



DSCF8268.jpg



DSCF8304.jpg



DSCF8318.jpg



DSCF8317.jpg



DSCF8244.jpg



DSCF8322.jpg



DSCF8281.jpg

Edited by EF Ian
Link to comment
Share on other sites

  • Replies 116
  • Created
  • Last Reply

Top Posters In This Topic

After a proper search for rust I did manage to find some unfortunatly. I found rust on the fuel tank, one of the chassis legs in the engine bay, both rear wheel arches and a little near the radiator. I took them all back to clean metal so hopefully thats an end to it.



Fuel Tank, noticed a few tiny spots of rust, but after removing the paint from those areas I found there were rust spots all over it and ended up stripping the whole thing, I managed to wire brush them all back to cleanish metal, then treated it with Bilt Hamber Deox Gel which did a good job before snading, cleaning and priming it prior to painting. It will do for now but I'll get a new tank at some point.

DSCF8342.jpg


DSCF8343.jpg



After:

DSCF8347.jpg




Bay, got rid of all the rust, one advantage of a black bay is that its easy to match, what I've done will do for now, I'll be getting a full bare metal respray in the bay in the near future.

DSCF8351.jpg


DSCF8349.jpg


DSCF8353.jpg


After:

DSCF8357.jpg


DSCF8358.jpg




I also sanded and painted the brake booster, unfortunatly it got some rain drops on it before it had fully dried and it ruined the finish a bit, but again it will do for now, thats not rust behind it btw, just grease.

DSCF8359.jpg





Polished up the lips on the wheels a bit:

DSCF8367.jpg





Got to work on the rear wheel arches, any rust I found was ground back to clean metal, sanded, cleaned, primed, painted and then undersealed:

DSCF8354.jpg



P-side before:

DSCF8361.jpg



P- side after:

DSCF8373.jpg



Drivers side before:

DSCF8377.jpg


During:

DSCF8381.jpg


After, I also painted the brake drums.

DSCF8386.jpg



DSCF8385.jpg








While I will definitly be changing my brake setup for something much better I thought I might aswell smarten up the stock calipers for now, brakes aren't the first thing on my list so the stock ones will be staying for a while yet.

Wire brushed and cleaned my caliprs and deck bells ready for painting.
DSCF8389.jpg


DSCF8390.jpg



DSCF8391.jpg


DSCF8394.jpg


DSCF8395.jpg


Its pretty clean in the wheelarches and I didn't find any rust, however to make sure and also make the finish look a lot smarter I'll also strip it back to bare metal for a respray at the same time as I do the bay, I'll also be seam welding around that area anyway.




I polished and waxed the front end, I have since finished the car, but didn't get any chance to take photos.
DSCF8403.jpg



DSCF8399.jpg



DSCF8401.jpg



DSCF8404.jpg




I drove 1000 miles in just less than 3 weeks and loved every mile of it, unfortunatly the car is now tucked safely away in an Air chamber and I went back to work today. I'll look forward to getting her out next and getting on with some modification.

Link to comment
Share on other sites

I'm home for a week after finishing some more training so I got a chance to check out some of my new parts.

 

 

Airdam

DSCF9048.jpg

DSCF9045.jpg

 

 

Indicators for the Airdam

DSCF9050.jpg

DSCF9053.jpg

 

DSCF9039.jpg

DSCF9034.jpg

 

 

New PCV hose, bonnet adjusters and some new fittings for the inspection panels.

DSCF9055.jpg

 

 

 

Carbon Fibre BRE style rear wing, very lightweight and rather nice looking:

DSCF9057.jpg

DSCF9059.jpg

DSCF9060.jpg

DSCF9062.jpg

DSCF9063.jpg

DSCF9065.jpg

 

 

 

Coilovers, should do a nice job, fully adjustable and the quality looks very good.

DSCF9070.jpg

DSCF9076.jpg

 

Cut off my stock shock and weld this part on

DSCF9081.jpg

DSCF9085.jpg

 

Camber plates to weld in, only fitting these to the front for now:

DSCF9091.jpg

DSCF9074.jpg

 

DSCF9078.jpg

DSCF9079.jpg

 

 

New fuel filter and thermostat, hood prop rod (will get this chromed) as mine is missing and second hand dome light as my switch is broken, will swap internals to my unit as its cleaner.

DSCF9092.jpg

 

 

Relay to wire into headlights, should improve brightness and save my switch as at the moment power runs through the stalk switch to the headlights.

DSCF9096.jpg

 

 

 

Red stiched gear gaiter, thought mine was a bit tatty:

DSCF9101.jpg

 

 

Oil and Filter:

DSCF9106.jpg

 

MM Billtet adaptors allow me to run a CV joint setup and get rid of the U-joints:

DSCF9107.jpg

DSCF9115.jpg

 

 

 

Z31T CV driveshafts

 

DSCF9116.jpg

DSCF9120.jpg

DSCF9125.jpg

DSCF9130.jpg

 

 

 

Billet alloy lock pulls:

DSCF9141.jpg

DSCF9144.jpg

 

 

 

 

Got more on the way although mostly now I just need parts for re doing the wiring, paints, ss bolts, etc. Looking to get a custom made alloy fuel tank as I haven't been able to find a decent decond hand tank, I'll get it built with a baffle setup and an in-tank Aeromotive 340lph pump.

Link to comment
Share on other sites

Back on a 5 week Holiday so I've got this beast out again, been loving driving it the past few days. There are some big updates to come here in the next few days.

 

 

 

P1000949.jpg

 

 

 

 

P1000974.jpg

 

 

 

 

 

P1000951.jpg

Edited by EF Ian
Link to comment
Share on other sites

Big Update Time

 

 

So I arrived home to find a room full of parts awaiting me, it was like Christmas but better.  :shock:   :D

 

 

Heres most of the parts ready to get sorted:

 

 

 

P1000718.jpg

 

 

 

 

P1000719.jpg

 

 

 

Got my parts back from getting chromed:

 

P1000710.jpg

 

 

 

 

Stainless steel and chrome bolts/nuts/washer for the whole front end:

 

P1000715.jpg

 

 

 

A selection of paints:

 

P1000726.jpg

 

 

 

Solid front diff mount to replace the crappy strap, I can use the black bushing fitted as a snub so it only tocuhes when the diff moves up under power, if I find this not good enouth once I run more power I can fit the red bushing and have it solidly mounted.

 

P1000730.jpg

 

 

 

Ok, so I blew way too mich money on my battery setup, but I just love it  :D  Guess I must have a bit of carbon whore in me.

 

P1000736.jpg

 

 

 

P1000737.jpg

 

 

 

P1000742.jpg

 

 

 

P1000747.jpg

 

 

 

 

Battery through bulkhead fitting, as battery will be mounted behind the passenger seat:

 

P1000767.jpg

 

 

 

Big electric fan to replace the viscous one, should make for quiter running, better cooling and better looks, electric thermostat and fitting kit also:

 

P1000752.jpg

 

 

 

Most of the car is poly apart from the steering rack and arm bushes and the front anti roll bar mounts so as I'm going to be stripping the front end I'll finish it off, got some anti-roll bar mounts arrivng any day also:

 

P1000754.jpg

 

 

 

Steering arm boots:

 

P1000755.jpg

 

 

 

New CV boots for my driveshaft setup:

 

P1000756.jpg

 

 

 

Custom made shorter and stonger shafts for the Z31T cv setup:

 

P1000801.jpg

 

 

 

 

Billet stub axles with longer ARP stud bolts:

 

P1000793.jpg

 

 

To go with the billet cv companion flange convertors:

 

 

 

4.11 Final drive for longnose R200:

 

P1000814.jpg

 

 

 

 

No LSD yet but I will be getting an OS Giken 1.5 way CLSD:

 

P1000878.jpg

 

 

 

New Wheel bearings:

 

P1000897.jpg

 

 

 

New alternator with internal voltage regulator so I can get rid of the external one and tidy up the bay:

 

P1000803.jpg

 

 

 

Some wiring covers and heatshrink:

 

P1000759.jpg

 

 

 

Will make all my wiring look much neater (will use black heatshrink on the rest rather than red)

 

P1000820.jpg

 

 

 

AZC Billet alloy shorter steering arms to quicken the steering with built in bumper steer spacers:

 

P1000766.jpg

 

 

 

TTT Tension arms:

 

P1000760.jpg

 

 

 

 

My gearshift boot was looking to tatty so I changed it to a much nicer one (from an ITR):

 

P1000780.jpg

 

 

 

P1000784.jpg

 

 

 

 

New Mats:

 

P1000708.jpg

 

 

 

Fitted:

 

P1000872.jpg

 

 

 

 

P1000811.jpg

 

 

 

 

 

Brake Setup

 

Going to be running these bad boys on the front:

 

P1000827.jpg

 

 

 

P1000839.jpg

 

 

 

P1000835.jpg

 

 

 

P1000845.jpg

 

 

 

P1000848.jpg

 

 

 

Painted the unswept area of the disk so it won't go rusty:

 

P1000886.jpg

 

 

 

 

 

My Rear Setup, using this setup: http://forums.hybridz.org/topic/113199-yet-another-rear-drum-to-disk-conversion-option/ designed and supplied by Nigel White (Thanks Nigel) It will be getting installed shortly so my update will include what I think of the kit:

 

 

P1000822.jpg

 

 

 

P1000825.jpg

 

 

 

 

Painted up:

 

P1000898.jpg

 

 

 

The pad will leave this with a nice clean edge:

 

P1000894.jpg

 

 

 

Wilwood 1" Master Cylinder, reservoirs can be remote mounted but I won't be:

 

P1000788.jpg

 

 

 

P1000792.jpg

 

 

 

 

Brake Bias valve:

 

P1000750.jpg

 

 

 

 

Good quality fluid:

 

 

P1000751.jpg

 

 

 

And so they can fit under my wheels, some new wheels, will run these until I fit arch flares and then I'll move to wider Watanabes. They don't fit yet, but they SHOULD once I have my coilvers installed:

 

 

P1000768.jpg

 

 

 

P1000775.jpg

 

 

 

 

P1000774.jpg

 

 

 

 

My door pulls looked really bad, so I had to sort that:

 

P1000881.jpg

 

 

 

Much better:

 

P1000883.jpg

 

 

 

And finally a boring one, changed my thermostat yesterday:

 

P1000895.jpg

 

 

Thats most of the parts that arrived, still a few more to come also, including my new custom built alloy fuel tank.

Edited by EF Ian
Link to comment
Share on other sites

Changed my crappy old alternator for a more powerfull one with an internal voltage regulator, its a much better job, my interior and exterior lights now work better and brighter and I've got rid of the ugly external regulator:

 

Old One

 

P1010008.jpg

 

 

 

New One:

 

P1010010.jpg

 

 

 

Conversion Plug:

 

P1010012.jpg

 

 

 

Gets rid of this thing:

 

P1010015.jpg

P1010016.jpg

 

 

Also changed my sump gasket, oil and filter:

 

P1010033.jpg

 

 

And some more parts arrived with the sump gasket, bushes for the front anti-roll bar, new ball joints and a SS braided clutch line

 

P1010037.jpg

Link to comment
Share on other sites

Had a rather nice item turn up today.

 

 

 

[P1010066.jpg[/url]

 

 

 

 

My custom built Alloy Fuel Tank, built for me by Pro Alloy. Fits in the same as the original, I have it setup for use with carbs while I'm still running carbs but its also setup for a fuel injection setup and should be good to flow enouth for 600HP. Its got a proper intenal collector, baffles and is also filed with tank foam so I won't need to run an external surge tank. Its got a DeatschWerks DW300 fuel pump installed which can flow more fuel than I'll ever need.

 

 

P1010073.jpg

 

 

 

P1010076.jpg

 

 

 

 

P1010077.jpg

 

 

 

P1010078.jpg

 

 

 

 

P1010090.jpg

 

 

 

P1010079.jpg

 

 

 

P1010085.jpg

 

 

 

Had to change my fuel sender type, this should be more accurate and takes up less room but also means my stock fuel guage won't work so I will use this:

 

P1010096.jpg

Edited by EF Ian
Link to comment
Share on other sites

Love the fuel tank, why is it limited to 600? only a 8an feed?

Thanks. The tank itself is obviously good enouth for more than 600hp, but after 600hp I would likely need to add a second fuel pump.

 

 

Feeds are big enouth, did some checking up and even -6 should be enouth for more HP than I'll ever have, no point in going bigger as the outlet size from the pump is smaller so I didn't think there would be any point in going bigger than this.

Link to comment
Share on other sites

My Nardi Steering Wheel turned up today  :D  Along with a few fancy bolts:

 

P1010101.jpg

 

 

 

P1010103.jpg

 

 

 

This is actually nice to drive with, but it just hasn't got the looks of the Nardi:

 

P1010120.jpg

 

 

P1010127.jpg

 

 

Matches my red stiched gear gaiter perfectly

 

P1010126.jpg

 

 

7fab7165-c59d-4246-972a-0846dbaceb47.jpg

 

 

P1010136.jpg

 

 

e5ac0015-4dff-49c4-a23b-d303d8832279.jpg

 

 

 

Also since my new rubber arrived yesterday I went and got it fitted to a rim so I could test fit it on the car, using Toyo R1R's in 225/45/16. Test fitted it up and they fit the rear fine, doesn't fit the front yet but it will with the new coilovers so I've ordered another 3.

P1010108.jpg

 

 

 

P1010109.jpg

 

 

 

P1010113.jpg

 

 

 

P1010147.jpg

 

 

 

P1010139.jpg

 

 

 

Quite a cool looking tyre:

 

P1010155.jpg

 

 

 

Definitly looks better than the old rubber:

 

P1010142.jpg

Link to comment
Share on other sites

Been busy doing the wiring for my new fuel guage, takes a while to locate the correct wires and then do a neat job of running the wiring. One of the pistons on the drivers side caliper was sticking on, so I ordered up a new seal kit, took it out and gave it a good wire brushing, should do until I get my new setup on.

 

A few more parts have arrived:

 

 

New dust boots for my TRE's and new wheel nuts in 12x1.5 size to fit the new wheels and new wheel studs:

 

P1010182.jpg

 

 

 

Switch for the fan, a few wiring connectors and crush washers and the fittings for my fuel tank. New clutch slave cylinder also as no sooner than I fixed my brakes than my clutch went, seemed it had been leaking for a while but only failed completly when I ran out of fluid, so got a new one ordered and fitted:

 

P1010193.jpg

 

 

 

ARP Extended wheel studs for the front Hubs:

 

P1010187.jpg 

 

 

 

These fittings allow me to use 5/16 fuel line for the carb setup, once I start using the pump I will use braided SS AN type lines.

 

P1010196.jpg

 

 

 

Installed and wired in switch for the Manual override for the electric fan:

 

P1010204.jpg

 

 

 

Nothing too exciting there, but she is off to the bodyshop tomorrow, going to be a busy day and likely a busy two weeks, got lots to do.

Edited by EF Ian
Link to comment
Share on other sites

I made some progress today:

 

 

 

Got the fuel Tank out, didn't get round to fiting the Pro-Alloy tank as I am going to get some stainless tank straps made up:

 

P1010223.jpg

 

 

 

Got the engine out:

 

P1010224.jpg

 

 

Front end is mostly stripped:

 

P1010228.jpg

 

 

P1010225.jpg

 

 

 

Won't be using most of this stuff again:

 

P1010232.jpg

 

 

 

P1010230.jpg

 

 

 

How I left her at the end of today:

 

P1010233.jpg

 

 

 

Still loads to do, but its a start.  :D

.

 

 

 

 

.

Edited by EF Ian
Link to comment
Share on other sites

Bay is completly stripped and all unwanted brackets cut off;

 

P1010262.jpg

 

 

 

Removed the battery tray as I have something much neater planned but also because its a well know place for rust, just as well I did as that was one of two places where I have a rust problem:

 

P1010264.jpg

 

 

 

End of the day, on trailer ready to be taken for blasting tomorrow:

 

P1010268.jpg

 

 

P1010265.jpg

 

 

 

Engine is looking a bit cleaner also:

 

P1010269.jpg

 

 

P1010270.jpg

 

 

 

 

Managed to find time to polish an Evo X also, came out nice:

 

P1010275.jpg

Link to comment
Share on other sites

The car is away getting media blasted today, will either be back tomorrow or on monday.

 

 

 

I finished cleaning up the carbs, they are not great, but better than they were. Did a bit more work with the engine, the block seems to have changed color.

 

P1010295.jpg

 

 

P1010291.jpg

 

 

P1010290.jpg

 

 

P1010289.jpg

 

 

 

I took the steering arms, balljoints, brakes, discs and backing plates off the hubs ready to fit my coilovers, none of which will be going back onto them:

 

P1010284.jpg

 

 

 

Got the new threaded tubes welded onto my hubs:

 

P1010286.jpg

 

 

P1010285.jpg

Link to comment
Share on other sites

Possibly, I was planning to go with the Mckinney mounts as from all the mounts I've looked at they seem to mount them engine the furthest back in the bay while still allowing the stock shifter position to be used and also come with a gearbox mount. If I could get alloy mounts that mount it in the same place then I'd probably go with them instead.

Link to comment
Share on other sites

I have their 240 mounts, although the engine mounts are ok, the trans was a joke. I had to make a custom one to hold that kind of weight. Yes it fit but the weight at the given moment was just not a bolt on solution. The trans mounts on the 260 and 280 are different maybe they are better. Matter of fact i think i have a trans mount for one.

Link to comment
Share on other sites

Which style of mount did you get with the Mckinney mounts? From what I see they do two, one looks a bit like the stock mount style and the other seems to bolt throguht the chassis and bends round under the transmission tunnel.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...