Jump to content


Photo
- - - - -

Spindle-Pin-Puller Loaner program


  • Please log in to reply
298 replies to this topic

#1 Dave

Dave

    Member

  • Members
  • PipPipPipPip
  • 347 posts
  • LocationPortland Oregon

Posted 29 August 2006 - 08:29 AM

The old thread was accidently deleted so we will just start a new one. To borrow a puller it will cost $20. The $20 is not a deposit, the money covers Priority Mail postage to you and prepaid postage to send the tool back.

All I ask is that when you request a tool that your ready to use it and it gets returned ASAP so others will have a chance to borrow it.

To return the tool all you will need to do is place the prepaid label on the Priority Mail box and set it out for the postman. There is no need to make a trip to the post office.

jtmny1999 has just used the tool and is sending it back. He said that it took a total of 10 ten minutes to pull both spindle pins. If all goes well it is a easy job, however some pins can be real nasty.

veritech-z was the last one to request a puller so the puller will soon be heading his way. At the moment this is the only loaner available unless some of the others start to turn up.

To request a puller just reply to this thread and send me a PM.
Dave....
V8-240Z Built Tuff
With Chevy Stuff
Posted Image

#2 veritech-z

veritech-z

    Mad Max Zed

  • Members
  • PipPipPipPipPipPip
  • 1600 posts
  • LocationTampa/Orlando, FL

Posted 29 August 2006 - 08:41 AM

I'm still interested, you've got PM.
-Max


www.maxacree.com
www.360ed.com

"I put on my robe and wizard hat.."




#3 nullbound

nullbound

    Rhymenocerous

  • Donating Members
  • PipPipPipPipPip
  • 828 posts
  • LocationRoswell, GA

Posted 29 August 2006 - 09:14 AM

I'm interested and ready to use it whenever its available.

#4 tah

tah

    Junior Member

  • Members
  • Pip
  • 15 posts

Posted 29 August 2006 - 09:39 AM

Which spindle are you talking about here....the rear pins? If so I need this soon.

#5 jtmny1999

jtmny1999

    Member

  • Members
  • PipPipPipPip
  • 397 posts
  • LocationLancaster, CA

Posted 29 August 2006 - 10:49 AM

Which spindle are you talking about here....the rear pins? If so I need this soon.


Rears.

Dave,

I sent it out today so it will be in you’re hands shortly and thanks for doing this it is really appreciated.

Jose
RB25DET 240z
Posted Image

#6 Dave

Dave

    Member

  • Members
  • PipPipPipPip
  • 347 posts
  • LocationPortland Oregon

Posted 29 August 2006 - 11:24 PM

I'm still interested

veritech-z your next in line and the puller should be here Thursday 08/31/06 and ready to send to to you the same day. PM me if a delivery date of Saturday or Tuesday will work since Monday the 4th is a holiday.
Dave....
V8-240Z Built Tuff
With Chevy Stuff
Posted Image

#7 Dave

Dave

    Member

  • Members
  • PipPipPipPip
  • 347 posts
  • LocationPortland Oregon

Posted 31 August 2006 - 12:31 PM

The puller is back and ready to send to the next member. veritech-z is the next in line followed nullbound. veritech-z needs to PM me ASAP or the puller will go to the next in line.
Dave....
V8-240Z Built Tuff
With Chevy Stuff
Posted Image

#8 Dave

Dave

    Member

  • Members
  • PipPipPipPip
  • 347 posts
  • LocationPortland Oregon

Posted 31 August 2006 - 08:15 PM

The puller is on its way to nullbound, he will post to the thread when the tool is on its way back.
Dave....
V8-240Z Built Tuff
With Chevy Stuff
Posted Image

#9 nullbound

nullbound

    Rhymenocerous

  • Donating Members
  • PipPipPipPipPip
  • 828 posts
  • LocationRoswell, GA

Posted 06 September 2006 - 05:07 AM

I got the puller over the weekend and should be pulling my pins this weekend. I'll post again when the puller is heading back. Thanks greatly for sending it so quickly.

#10 nullbound

nullbound

    Rhymenocerous

  • Donating Members
  • PipPipPipPipPip
  • 828 posts
  • LocationRoswell, GA

Posted 18 September 2006 - 06:17 PM

I finished with the puller tonight and will drop it off at the post office tomorrow. I pulled 4 pins with only the one issue. This tool worked amazingly well! And Dave has definitely been awesome to work with.

As for the issue I mentioned above, I had an issue with one of my spindle pins where one of the threaded ends was slightly bent. I had bought rear 280 suspension assemblies and the nuts on the pins were already removed. I didn't realize one of the threaded ends was slightly bent until it was too late. When using a wrench to start turning the end nut to pull the pin, the puller pulled through the threads on the pin. I had messed up the threads in the puller and on the pin itself...

I emailed Dave about it and he immediately sent replacement parts so that I could get the pin pulled. I was surprised at how quickly I got the replacement parts.

Thanks greatly, Dave!!

#11 denny411

denny411

    Member

  • Members
  • PipPipPipPipPip
  • 982 posts
  • LocationWapakoneta, Ohio

Posted 23 September 2006 - 12:14 AM

I am getting ready to section my struts, and could really use the pin puller. How soon will it be available?
Thanks,Denny
denny411@gmail.com
cell,419 773 9404
I do not think much of a man who is not wiser today than he was yesterday -Abraham Lincoln-

#12 Dave

Dave

    Member

  • Members
  • PipPipPipPip
  • 347 posts
  • LocationPortland Oregon

Posted 25 September 2006 - 12:56 PM

I have the spindle pin puller back and ready to send out. To borrow a puller it will cost $20. The $20 is not a deposit, the money covers Priority Mail postage to you and prepaid postage to send the tool back.

All I ask is that when you request a tool that your ready to use it and it gets returned ASAP so others will have a chance to borrow it.

To return the tool all you will need to do is place the prepaid label on the Priority Mail box and set it out for the postman. There is no need to make a trip to the post office.
Dave....
V8-240Z Built Tuff
With Chevy Stuff
Posted Image

#13 denny411

denny411

    Member

  • Members
  • PipPipPipPipPip
  • 982 posts
  • LocationWapakoneta, Ohio

Posted 25 September 2006 - 02:57 PM

Dave,
I will papal 20.00 to you later this evening.

BTW, I still need a top rear strut mount for my 75 280.
If anyone has one please let me know asap. I posted this request in the classifieds,but I`m not sure how many people check them regularly.


Thanks,Denny
denny411@gmail.com
cell,419 773 9404
I do not think much of a man who is not wiser today than he was yesterday -Abraham Lincoln-

#14 Dave

Dave

    Member

  • Members
  • PipPipPipPip
  • 347 posts
  • LocationPortland Oregon

Posted 28 September 2006 - 07:17 PM

I have the spindle pin puller back and ready to send out. To borrow a puller it will cost $20. The $20 is not a deposit, the money covers Priority Mail postage to you and prepaid postage to send the tool back.

All I ask is that when you request a tool that your ready to use it and it gets returned ASAP so others will have a chance to borrow it.

To return the tool all you will need to do is place the prepaid label on the Priority Mail box and set it out for the postman. There is no need to make a trip to the post office.


Just got a PM from Denny that he has his pins out and did not need the puller after all.

So the puller is still here and ready to send any time.
Dave....
V8-240Z Built Tuff
With Chevy Stuff
Posted Image

#15 jtmny1999

jtmny1999

    Member

  • Members
  • PipPipPipPip
  • 397 posts
  • LocationLancaster, CA

Posted 29 September 2006 - 03:52 PM

Here is the part # in case you need new ones.
Item # Desc. Price
55540-N3701 SPINDLE-LINK $21.21
RB25DET 240z
Posted Image

#16 Guest_beaddds_*

Guest_beaddds_*
  • Guests

Posted 04 November 2006 - 08:49 AM

Dave,

Thank you for pointing me in the right direction with regard to the spindle puller loaner program. I joined the site last night. You guys have a great deal to offer here. I would like to get on the list for the loaner program, but I am a little unsure as to the PM terminology. If you can clear this up for me, I would like to complete the transaction as soon as possible.

Thank you again for leading me to hybridz.

Regards,

Paul
BEADDDS

#17 Dave

Dave

    Member

  • Members
  • PipPipPipPip
  • 347 posts
  • LocationPortland Oregon

Posted 06 November 2006 - 11:15 AM

Paul,
Your next in line for the puller, I looks like Wednesday 11/8/06
it will be on its way to you. I will shoot you a E-mail when it
leaves here
Dave....
V8-240Z Built Tuff
With Chevy Stuff
Posted Image

#18 Just Jim

Just Jim

    Member

  • Members
  • PipPipPip
  • 98 posts
  • LocationSouthern California

Posted 13 December 2006 - 12:53 PM

Hey Dave,
Sent you a PM about borrowing the tool.
Thanks,
Jim
'72 240Z 302/C4 Junk Yard Refugee
'62 Falcon 351W "Just Falcon Around"
'58 Morris Minor 289/C4

#19 MarkM

MarkM

    Junior Member

  • Members
  • Pip
  • 7 posts

Posted 19 December 2006 - 06:00 PM

Hi Dave,

I'd like to borrow the spindle pin puller next go-round. Just sent you a PM.

Thanks,

MarkM

#20 Ledphoot

Ledphoot

    Member

  • Members
  • PipPipPipPip
  • 224 posts
  • LocationNC

Posted 19 December 2006 - 09:37 PM

Guys there is one on Ebay right now with 3 days left on the bid if you're interested. I saw it while searching z stuff http://cgi.ebay.com/...sspagenameZWDVW I dont know the seller and have nothing to do with this listing just FYI if anyone wants to buy one.....
LedPhoot Racing
Lo-Buck No-Buck Specialists
:banghead: " if it ain't broke...drive harder.."




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users