Jump to content
HybridZ

zthis

Members
  • Posts

    102
  • Joined

  • Last visited

Profile Information

  • Gender
    Not Telling
  • Location
    Newfoundland Canada

zthis's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. Yep Dana 60 with 4 link.This summer its been 11.3-11.4 on the motor so I'm normally getting about a second and a half
  2. I've been running NOS for a few years now I finally got around to adding a NOS fuel return line no more stumble of the line but now I have another issue to get around. See video link. 350SBC with 180 Shot NOS
  3. Those tires are big hope your planning on making some serious HP.
  4. our timing system only gives 660 ET that was 6.298
  5. LOL you were close ... just an unused air strip which is of a back road in the middle of nowhere.
  6. 11.75 to 1 forged pistons, crank and rods, edelbrock 64CC performer rpm heads, comp xtreme solid cam 288, roller rockers holley 750DP 350 tranny with TCI 3500 stall. Same day at the track I was running 11.30 on the motor
  7. Well I finally made it into the 9s 9.882@135.58mph with a 1.434 on a 210 shot of NOS theres more there yet heres a video of the pass http://ca.youtube.com/watch?v=DHNMeBd-10M
  8. I should also add the reason behind this post is that I ran too much NOS (210HP) into a SBC (which BTW grumpy had advised me not too in a previous post) anyway I think i lifted the head, overheated the engine, melted the strap of a spark plug and broke of a rocker arm stud all on the same run trying to better my newest personal best ET of 9.88. I'd like to change from a FEL PPO precompressed 1003 head gasket to a multi layer gasket but i'm not sure if i can do this as there's a slight ridge on the heads from the previous gaskets. I'm trying to make the motor strong enough for 250HP NOS runs.
  9. thanks grump can you tell me anything about "Undercut" studs are they worth the extra $$$
  10. I'm thinking about upgrading my after market head bolts to ARP studs. Can someone tell me what the advantage is to having the "uncut" stud version and if there is really any advantage to having 12 point nuts. thanks Curtis
  11. GrummyVette as always the voice of knowledge and reason.....oh well better go to the garage and squat all my 250+HP NOS jets with a hammer before I do something stupid. Thanks I guess
  12. Hey I have a 350 SBC gm forged crank, eagle rods and forged pistons 350 tranny . I'm setup with a Dual stage Big Shot Nitrous system. I've made one "bad" pass with some issues running a 150210 Shot that was a 10.004 at 135. After solving the issues I went to a 200 of the line switching to 275 Shot while still in 1st gear car hooked awesome BUT the timing system at the track failed and I got no time slip but it felt alot better than a 10.0. So my question is whats the limit of NOS on a motor of this size. I basically want to make a couple of 9 second passes a year and not every weekend. Curtis
  13. It cost me around $4000 I bought pretty much everything brand new except for the housing all top of the line gear strange axles, adjustable stocks, bears rod ends, chrome moly rods, drive shaft etc etc . All custom made roll bars and 2X3 frame rails things worked out really nice I lost alittle seat room (cross frame brace was centered over the old seat belt holes) but for the limited amount of street driving I can live with it. Car feels totally different leaving the line than with the stock rear end. Much more solid feel not to mention much less worries about breakage. Next weekend at the track i'm upping the NOS fingers crossed i'll get a 9.
×
×
  • Create New...