Jump to content
HybridZ

ZMONSTR

Members
  • Posts

    24
  • Joined

  • Last visited

Profile Information

  • Gender
    Male
  • Location
    Ohio

ZMONSTR's Achievements

Newbie

Newbie (1/14)

1

Reputation

  1. I have a restored 260z with cut springs. The car bottoms out a fair bit and in general doesnt like bumps in the road. I am attaching a pic to let you see the current stance and cut springs I have the OK from SWMBO to upgrade a few things to the tune of 3k or so. So I am looking at coilovers and new seats. Based on reading here, it doesnt seem to matter what you buy for coilovers..you get about the same thing. My question is are coil overs going to improve the handling of bumps, or at least stop the bottoming out with the same stance? Thanks
  2. It's is a 5speed from a ZX! Please educate me some!
  3. This is why I posted.. the shifter and opening for ash tray dont quite line up. I would have to push the center console in..but then I get big misalingment with the lower console meeting the center. I went with this position becuase the shifter is not hampered, and a new shifter boot should cover. As for the ash tray, I intend to do something else with it.
  4. I am trying to limit my cutting into the carpet as I dont want it to be loose or a saggy. Right now its screwed into the carpet and padding and its holding very well actually
  5. Always.. your pic is reassuring! I tried in vain to find a pic with google but couldnt. As for holes, the previous rebuilt covered trans hump with carpet so I had to guess some. I have left the carpet, except for cutting some away for the proper redo of the choke and access to the dip for the ash tray. I do not intend to put an ashtray in the car, but some kind of cup holder
  6. Hello, My car was redone without a center console (not sure why). I have purchased one, put it in and would like thoughts on the alignment. Something is a bit off. I am attaching all the pics i took just to be safe. The problem I am seeing is that the shifter and dip in trans well for ash tray is a bit far foward compared to the opening(last pic). I placed the center console based on where i think it should allign with the console above it (1st pic). Its not pushed in very far, and I thought those elements should align. I can push more if I want, but ruins the alignmet of the bottom console with the middle. Thoughts?
  7. I will be getting BC coilovers soon, but would like to keep the same stance I have now. The current setup was achieved almost 10yrs ago with cut springs. I guess my real question is do I want the extra low springs or normal springs?
  8. One more question. The master cylinder is a NABCO 7/8. I roughly measure the brake booster between 8 and 9 inches diameter . Does this mean any 240 or 260 brake booster would be acceptable? Whats on there is an after market Bendix label, made by Master Vac. Part number is 285186.419240. Google is absolutely no help on this part
  9. Brake pedal is very hard to push. When the car is in idle and I push the brake pedal, it cause the idle to drop severly causing a stall or almost stall. There is also a hissing noise down near the brake pedal when its pushed. Thoughts?
  10. The Z store comes up, and I have checked there before, and all I find are Urethane, not rubber. Maybe I am not in the correct section?
  11. I have been looking at after marking tension control arms, and it looks like they remove the bushings and go with a more rigid setup that is adjustable. Does this improve the ride, or just the handling?
  12. I have been in my fair share of Z's but havent been in a classic Z for 20yrs at least. I took an hours drive, me driving, in a 370z Nismo.. and that is a stiff ride. The ride in the 260z just feels bumpy, not stiff. I may not be an expert, but I am pretty sure the current setup is designed for looks that than performance and/or feel. Right now, just a matter of understanding everything about coilovers vs say a Eibach progressive lowering spring and Tokico Illumina strut. I think that a spring and strut might raise the height of the car from what its currently at, but give me a much better ride. Plus the cost is more palatable.
  13. LOL. Really appreciate your concern and generous offer, but I am determined to make it right and learn something in the process
×
×
  • Create New...