Jump to content
HybridZ

Apex944

Members
  • Posts

    63
  • Joined

  • Last visited

  • Days Won

    1

Apex944 last won the day on April 24 2012

Apex944 had the most liked content!

About Apex944

  • Birthday 07/18/1989

Contact Methods

  • AIM
    nightkd
  • MSN
    apex944@hotmail.com

Profile Information

  • Gender
    Male
  • Location
    Sacramento, CA
  • Interests
    Mechanic

Apex944's Achievements

Newbie

Newbie (1/14)

-2

Reputation

  1. Last I saw it was reported stolen... I believe it was about 4 or 5 months ago, maybe longer. Something about it being built to look like it does here in Sacramento and then a guy in Chico bought it which is probably the starter of this thread. The starter of this thread probably got tired of it so they sold it to someone back here in Sacramento and then a few months after the new owner bought it it was stolen. Whomever it was made a craigslist post about it being stolen, I don't know if it was found or not though. Here's a link to another thread where they were talking about it... My link
  2. Thanks for the link, I'm actually watching those as a back up in case I can't find a set for cheaper as that's a little much for a set of rails. For $90 I could buy a set of seats with the rails attached here locally and get the seats as a bonus. Still looking for the rails if anybody has a set. I have some part's I could trade if anyone's interested.
  3. Looking for a set of driver and passenger side seat rails from a 240Z. I can get by with just a passenger side set for now but would prefer both driver and passenger sides. Please either PM me or post here. Also please be reasonable with the prices. Thanks
  4. Might want to search some foxbody and SN95 forums to find the differences between your '95 engine and fox 85'-93' engine's. Only difference engine wise that I know of is they have cast hyper pistons compared to the fox car's forged pistons. If going to a T5 trans you will need to research and makes sure you know which trans will bolt to your engine as 85'-93' engines cannot use 94-95' transmissions due to the 94'-95' car's using a different input shaft from the trans so I am fairly sure that the 94'-95' car's cannot use the earlier 85'-93' transmissions. Brian's subframe for the 302 engine is a really great piece, it's what I'm using to put an '86 5.0 HO ( not my first choice engine but was practically free with low miles ) engine into my '73 240Z.
  5. Perhaps the last one Les will make out of carbon, he didn't want to bother with it much because of the little pay off from what he told us but I've got my body guy making a few carbon one's off of the scoop I got with some improvements to the mounting design ( mount's being part of the mold and not clips or globs of resin holding the studs in random locations like mine) and a few other thing's...
  6. To help clarify the pricing, my girlfriend bought a fiberglass one for me from Les back in November as a secret Xmas gift. Said she paid $250 plus shipping for it which was $275 total. ( Corrected by her ) Guess Les changed his mind and will be making them to order as RB240ZDET has posted below. I'm having my carbon guy make me one out of carbon fiber as the last Les told us was he wasn't going to make anymore at all when we talked to him.
  7. It just so happens that while I was at SEMA in Vegas this past week there was a new product out that does exactly what you are looking for, it adapts to the end of the red spray tube that you stick into the nozzle of your normal spray paint can. You can feed it into the body cavity that you need to seal and it sprays 360 degree's of whatever you want to spray it with. The rep suggested their weld through primer with zinc similar to what 240zip said as it allows you to weld and not have to be sprayed with a sealer as it doesn't burn. It's basically an extension that slips over the red spray tube that is flexible with a special spray tip on it that spray's in a circle form to coat the surrounding area as you slowly pull the tube back out of the cavity. Unfortunately I have stacks of information I brought back with me that I need to search through to find the company's name but some google searching should turn something up about it. I'll try to go through the pile of stuff tonight and edit this post with the name of the company and the tool.
  8. Ran into the same issue with the AZC springs being NLA myself not to long ago. Located in the FAQ's section... Installing Tokico 280Z HP Springs in 240Z The 280Z spring's are the one's you want NOT the ZX springs. They are linear for a fact as I have a set of them on my '73 240Z and are the same diameter as the 240Z springs so they are a direct fit. The 240Z tokico springs are progressive front/linear rear which is why people use the 280Z linear front and linear rear springs instead which are 185 lb front 200 lb rear spring rates. The tokico springs are currently the only option if wanting a drop in replacement, otherwise you'll have to do a coilover setup using the threaded sleeve's and aftermarket springs from QA1 or other similar spring manufactures to get anything higher than a 200 lb rate spring. I have not yet driven my car but they should be stiff enough for good handling and a comfortable ride for my 302 HO powered Z. Quick search will show other V8 Z owners that use them and like them as well even with a heavier small block chevy 350 in the car. If you still have the L6 they should be enough spring rate for your liking.
  9. Looking for an MSA type 1 fiberglass front air dam for my 240Z, can pay for shipping if needed. Located in Elk Grove, CA 95624 Feel free to offer other 240Z air dam's though as I currently don't have anything on the front of my car. Thanks
  10. AZC told me they won't be making anymore of the heavy duty springs for the 240Z for a long time if ever when I called them about a month ago....had a pretty rude tone over the phone as well I might add. I instead purchased a set of the 280Z tokico springs from beta motorsports and according to their spec's they are the same spring rate's as the AZC springs. Seem to work quite well for me but I've yet to drop the small block ford into the car and see where and how well it sit's... Perhaps the tokico's will work for you?
  11. Looking for either new or lightly used stock 240Z or MR2 Tokico HP/Illumina shocks as well as Arizona Z Car springs or something similar. Figure I would see if anybody had anything laying around before buying another new set as they are only temporary anyways. I'm located in Elk Grove, CA 95624 Please PM me with offer's. Thanks
  12. I've got a set of Enkei 92's with center cap's that I just posted in my sale thread. 15x7 0 offset 4x114.3 I'm located in Elk Grove, CA 95624 Can ship all 4 for about $550 OBO Let me know, thanks
  13. Looking for a cheap 280Z tachometer, hopefully in the $20 - $35 shipped range if at all possible. Not looking for anything perfect, housing damage is ok as I only need the gut's from the gauge. Also looking for a 280Z fuel level/voltage gauge in decent shape. I live in Elk Grove, CA and will use verified paypal for payment. Thanks
×
×
  • Create New...