Jump to content
HybridZ

Sanchez

Members
  • Posts

    195
  • Joined

  • Last visited

  • Days Won

    2

Posts posted by Sanchez

  1. I made the same mistake setting my L28 rebuild I did in high school. I realized my mistake and Corrected it after having some noise on the drive home. It’s an easy mistake to make. Check the lash semi-regularly too. For a while after break-in I had one valve that would lose adjustment slowly until about 1,000 miles on the engine when it finally decided to stay where I set it.

  2. On 12/5/2021 at 10:35 PM, Sanchez said:

    5702CD66-3DE5-4DFD-A484-ACBFCD71723A.jpeg

    @Gumiho3

    If you are referencing this picture then yes that is a green wire that supplies power for the PNP. In my case Hexa Garage never hooked up the wire running from my PNP to the ECU so I was powering that green wire at the plug but it never told to ECU to trigger a start signal and I had to borrow a snap-on diagnostic tool with Nissan protocols to see that, so you may want to bypass your PNP switch entirely and just run a signal directly to that pin on the ECU plug. I’ll check my FSM quickly and get that pinout for you. 
     

    It is pin #109 (marked it on the image). Remember this pin out is from the harness side so it is as if you are looking through the connector when the wire side is facing you.IMG_5351.jpeg.ad9b456799461eb862001905460a3257.jpeg

    • Thanks 1
  3. Sounds like it might be able to work both ways. I would assume with some additional chassis bracing it would be less likely to flex in that area, or the Z might be pretty rigid in that area already. It would be interesting to hear from a couple other people who have gone the sealant route and hear what kind of sealant they used (how hard/soft it is) and whether or not they had any sort of other chassis bracing done (stitch welds, cage, strut bars, etc).

     

    If I remember the Precision brand window gasket has an issue with gaps in the corner and I could see sealant being helpful in that case, but my 50yr old original gasket was still pliable with no leaks and held the chrome trim fine when I removed it (not a spot of rust in the windshield channel either).

     

    I think I remember a thread not too long ago about the possibility of “frenching” the windshield by having glass made a little larger in the dimensions and deleting the gasket entirely for sealant. It might have some more information about using sealant.

     

    If it turns out nobody is having an issue with using sealant than it’s probably just down to dealers choice.

  4. I asked a buddy of mine (he’s an auto glass maker for customs and does a lot of windshield repairs for insurance) when he brought over some tools to help pull my glass from the Z. His response was to do it exactly the way it was done from factory. That would be dry install using a quality window seal. His reason was that some of these older unibody vehicles are designed that they tend to flex around the pillars, and the heavy duty sealant that is used for glass install can be hardened to the point that when the chassis flex’s a bit it can crack the glass. Now depending on where you live or the cars purposes you may have flat roads all the time, but in the Midwest I can definitely see how some of these potholes on the road could easily cause that to happen.

  5. 16 hours ago, Gumiho3 said:

    Hey Sanchez, how the build going?

     

    My ECM decided to die on me and now I have a surging idle. I plugged consult in to do a idle relearn, but consult says I have a NG neutral switch. With it being this way I cannot start the relearn with consult.

     

    Where did you locate the neutral switch? Have you ever heard of a vq37 with a surging idle? It goes from 800rpm to 3000rpm. It drops as it warms up.  When I unplug the gas pedal the idle stays constant but higher than normal(2k rpm)


    The build is going slowly, work has been hectic, I’m buying a house, and family member health has me slammed. I still get a few hours of work in on Sundays and when the weather is nicer I can squeeze some time in on Mondays hopefully. I have nearly finished up the body work on the front half of the car since my last update. Just working on getting some crush sleeve installed at the sway bar mounts, then I should be ready to mock up engine and trans placement.

     

    I haven’t fired up my engine in a while, but when I did it didn’t have surging issues. When I got my wiring and ECU modified by Hexa Garage they never connected the wire from my neutral safety switch to the ECU, so I had to go into the harness and make that connection. However; that caused “no start” logic so the engine wouldn’t even fire until it was fixed.
     

    But I maybe able to help you diagnose with some knowledge I have from my RX8. When it gets cold and I haven’t driven the car in a while my idle surges at idle until I press the clutch and put the car into a gear. Then after some driving the trans warms up and the neutral switch stops sticking. Modern car logic has different idle speeds for different situations on cold starts, so neutral with clutch off it will high idle until up to temp, but once in gear it lowers the idle so you aren’t trying to shift into first at 1500rpm from a stop. The sticky neutral switch keeps pulsing the on/off signal to the ECU causing it to go from out-of-gear-fast-idle to in-gear-fast-idle. Add that to the fact you need to do an idle relearn and It makes sense why you are getting such a huge surge from 3000-800rpm.
     

    If I remember correctly the neutral switch (and clutch switch which could also be at fault, so try the test on both) are just voltage on/off switches, so try feeding a 5-12v signal to those wires going to the ECU using a power supply or spare battery and report back if anything changes.

  6. That Autozone grommet seems like a decent replacement. Though when mine came out it seemed like it was originally a hard plastic, and not rubber that turned hard over 50yrs. My plan was to turn one on a lathe out of a small puck of delrin. Now most of my linkage were so rusted and seized they had to be cut off, so if anybody has a line on reproductions or DIY solutions I’d appreciate a PM with the info.

  7. I don’t know exactly where you are located (I.e. sunny Florida or an overcast northwest state), but with polarized sunglasses being so cheap I never even use the visors in any of my cars. I just keep a pair of sun glasses in each one. That’s my money saving tip… on to an actual solution if you want them for the originality of the car.

     

    The Z sun visor I found basically ineffective in Florida. They are small and line up in way the sun would still peek through the top side. A modern retro fit could end up being harder to do than just finding them from part out and taking the visor off the swing-arm and making your own that fits better out of some aluminum, plexiglass, cardboard with a leather or vinyl cover. I plan on putting mine in because the lady likes to use it. I’ll add it to the list of things to make a how-to on when I get around to it.

  8. On 10/2/2023 at 11:06 AM, Nismospek said:

    Have you mocked up the headers on yours? It looks like I am going to need to get the stock ones modified since they point towards the firewall. 

    They do need to be chopped right at the down pipe flange and rotated to clear the transmission tunnel for any stock or stock-like aftermarket header. I may chop it and extend it to use v-band clamps instead. I still haven’t decided on it.

     

    I just got back to working on it after a few months break to focus on opening a new laboratory facility at work… but in that time I came across a series 1.5 for a steal and picked it up. The unibody is pretty tweaked, but it has some solid parts, perfect glass, and I’ll probably end up parting most of it out and use some parts for myself.

    IMG_5283.jpeg.abb0717205855788fb5447f2cfcd0768.jpeg

    IMG_5281.jpeg

    IMG_5282.jpeg

  9. So it’s been a while since an update. Progress stalled due a lengthy vacation followed by work being short staffed after I returned, followed by changing jobs which required opening and running a new facility, and finally an MG B that came to the garage for work that I ended taking on. A real whirlwind of stuff building up, but I’m ready to jump back on the Z now.

     

    Apex Engineered got me a new rear knuckle to fix the issue a bolt hole being unusable so I’m hoping we will get a video of the kit up on our YouTube soon.

  10. Realized it had been a minute since an update. Life and full time job getting in the way of doing serious work on the projects as you all are very familiar with. But I got some head way and updates.

     

    Engine:

    there is a company D&D Power Belts that makes a 31.75” outside circumference belt with 7 ribs that is a fit for the VQ37VHR with just an alternator and the stock tensioner. The part number is 310K7; however, they don’t have it in stock and it took 3 purchases from different suppliers who all sent me 315K7 instead before I finally got an answer that it would be a few months before they have it in stock. Would’ve been nice if they actually told me that before I had return multiple belts…

     

    Body:

    Driver front frame rail all welded in and started my cut for the patch on the passenger side. I’m going to do simple box tube to tie them together when done. Also started modifying the front front core supports to run the intakes for the engine up to the front out of the engine bay.


    Apex Parts:

    I’ve run into a few issues with the Apex Parts. They sent one of my rear knuckles which was welded to the coilover sleeve incorrectly causing the hub bolt to not clear. While they have been very responsive they still have not sent a working part out like they said they would. It’s been a bit frustrating, but I don’t exactly need the part at the moment and I understand they are busy fulfilling other orders… it just seems like this should’ve been sorted out a while ago and shouldn’t require me reaching out almost every week and still just hearing that they will get me a new one out.

     

     

    EF467E8A-2792-408D-B2D7-6F5761B11C48.jpeg

    1177B265-27B0-402C-9DEC-0A59DB326DD0.jpeg

    68E1E315-D7E1-41F7-A026-794FDAF99A34.jpeg

    9C30210F-6E8F-422D-B34E-D1D77584B944.jpeg

  11. So I tried to get some measurements but they are a bit more complex than some holes cut in a 90deg bend of metal. For some reason pictures I upload don’t turn out with great resolution, so it’s hard to see the detail I’m referring to. There’s some little lips here and there, and the slotted holes are angled. I’d definitely try to catch somebody parting one out cause it’s likely they’ll have them. If you want to make them it’s probably better to base it off one you have in your hand already than any measurements I could take.

    4959CF03-13AC-41F5-95DA-86E21810DD56.jpeg

    DA4E0CC1-69C9-41D2-AD33-451002A6458B.jpeg

  12. @fusion
    Zcardepot has reasonably priced reproductions available. Not sure how they compare to NOS or the more expensive reproductions I’ve seen, but they seem the same thickness as my original ones, which were in decent shape (unfortunately I forgot to remove them during sandblasting and don’t trust my original anymore).

  13. @Dat73z

    Thanks for info about the strap adjustment. Ideally I would like to avoid the tank sitting lower than factory. I probably should’ve done a few extra measurements while marking my cuts. I may be able to drop the plate I made another 2-3mm to make it work without using the adjustment in the J-bolt. Ideally this is only a temporary tank to get the car together and running first before I ditch it for a custom built aluminum tank, or I’ve even seen some companies making composite recreations of S30 tanks recently.

  14. Pretty much all of my suspension from Apex Engineered has arrived. Just waiting on the coilovers which are shipped separately by Riaction. All the parts are quality made, but the only issue I’ve run into is that they sent me a L/R outer tie rod instead of the R/R outer tie rod. I ordered 2 standard thread inner tie rods from Zcardepot, but they claim they have them for the left side as well… I don’t know if that’s true or not because I heard these RareParts tie rods are only for the right side. Can anyone confirm if Zcardepot was able to source a manufacturer of left hand inner tie rods? Apex has been amazing about responsiveness so I have no doubt they’ll fix the issue for me with a new part if needed. Second small bit of confusion is I ordered the rear 370Z single brake caliper mount that should allow use of the drum-in-rotor parking brake, but some quick test fitting looks like there might be clearance issues with the parking brake hardware. I will update after some more in depth testing.

    75AEE0D1-0579-4D28-B7C3-589C0BEE7D45.jpeg.fd8b616eeb625d335519c3c7a3f17db9.jpeg

     

    Still slowly getting my front frame rails together, taking my time to do it safely, strongly, and make sure everything is lined up very well. The Jeep CJ radiator looks like a great fit for a Z with a VQ in it. A little trimming to the radiator mounts that came on it and it will slip into place.

    A30AB426-C999-42C7-8510-52AC0E502FCA.jpeg.200b2b4c66eb1478eb96716ef4028674.jpeg

     

    Been working on the fuel tank too with a Holley Sniper return style in tank module. My measurements are a little off and the area I cut put the top of the piece in contact with the rear frame by 1-2mm but I think that can be solved with the adjustment in the straps and some slightly thicker rubber isolator pads. Can anyone confirm that there is some adjustment in the straps using the J-bolt? Also building a small swirl/hallway baffle box for the pump to sit in. I think my design should allow plenty of flow even at a 1/8 tank (if I ever let it get that low) while stopping any slosh from starving the pump.

    2439C3CC-0A07-452E-8B53-37D923F23DFF.jpeg.0d6a7313639d91e572a8658238781a4f.jpeg

     

  15. I know your struggle of owning a Z as teen and the learning as you go process. I’m now in the process of a full chassis up rebuild and engine swap 11 years after getting mine as a 16yr old. The wiring on these cars always gets messy. My suggestion is get both the Haynes wiring diagram and FSM diagram and compare both when doing stuff on it. The Haynes sometimes has circuits for optional stuff, and depending on how you like to look at multi switch diagrams the Haynes or FSM might be easier to read for you. I second going through and replacing all the fuses and fusible links even if they look good. I’ve seen fuses look good but not have continuity, and fusible links test out fine but not function for the load on a particular circuit because they melted just enough.
    If you have the money to spend now looking into the upgraded fuse boxes usual sold by Motorsport Auto is a good fire safety feature. Shorting across the old original hazard and flasher relays can kill them easily because they have shared circuits. take them out and bench test them, or just replace them with a modern Bosch style flasher relay. And check you multi switches for continuity too.

  16. Interesting… I can’t remember what year your Z is, but my late model year 73 240Z did not have any seals around the door switches. I was planning on doing away with them to simplify the wiring since we basically carry a flashlight built into our phones now, And living in the city I never felt like the courtesy lights made things brighter than the streets already are. It kinda looks like their purpose is to reduce shock to the plastic on the switch and keep it from fully bottoming out of the door is slammed. Maybe a good thick HNBR or Viton O-Ring glued around the perimeter would function similarly?

  17. Been a hot minute since an update. Progress slowed due to life coming up. I haven’t had a lot of time to do the welding needed to finish repairing the front frame rails and test fit the engine because we've been pretty busy at our garage doing repairs and getting ready for hosting Boeing’s Annual Car Show. I also ran into an issue with those little pocket to access the front cross member bolts on the front frame rail curtain. I swear they used to sell them individually but I can’t find them anywhere and they appear to be 16ga which my cheap metal brake won’t handle. Ran out of welding gas and my local AirGas was back logged because they are supplying gas to the construction team finishing up the new soccer stadium here. Lots of road blocks.

     

    What I have accomplished in this time:

    - Getting the fuel tank hot tanked this weekend and getting a buddy going on installing a Holley Sniper Return Module fuel pump hanger. It looks similar to the Aeromotive Phantom unit but $150 less and no foam baffle. But while I can make my own little metal baffle box for a few dollars.

    - Started welding some on the body panels, mainly rear hatch and the channel around it where some of the metal disintegrated.

    - Radiator. The inlet and outlet on the VQ37 is reversed from the L24 so the options are buying a 240Z rad and having the bungs cut and moved, or some crazy piping. After a lot of measuring and cross referencing I found the radiator from a 70’s-80’s Jeep CJ has bungs correctly placed, has a 24”x15.7” (LxH) core, so almost identical to the Mishimoto/Champion Z rad with a little taller core but same overall height. I’m going to purchase a cheap Amazon one so I can test fit it, then get a higher quality Champion rad later.

  18. Front frame rail moving along. Driver side ready to be tacked and tweaked after getting a liberal amount of 2k Epoxy primer in it. I’m thinking given this frame rail had to be welded after the crossmember I will need to do a bit of bracing with thick square either inside the rail and weld to it or some angle iron on the outside for support.

    FFE2B2AE-E97A-4FF6-B3A1-8C3446B02E47.jpeg.1e6930fa1b98715a48b6b1126c8c9339.jpeg

    43A2CEB7-0A28-40B5-A2BE-1D1B75A014B8.jpeg.ec2069a5bcd0896a4aa756faf62506b9.jpeg

    Ford Performance trak-loc arrived, the pumpkin in my 8.8 currently is being really stubborn so I might need to take it to an axle shop to separate it from the housing. And I’ll be ordering more suspension parts from Apex Engineered at the next payday.

  19. I’ve been looking into rim/tire combos recently and have settled on 17’s partially out of necessity, and partially out of trying to use as many easy to find parts for replacement in the future should I need so. I’m going to be using the Apex Engineered 8.8 subframe and front uprights which use 350/370Z brake parts very few 16” rims will clear and I need a 5x4.5 lug pattern. It’s looking like a set of Rota RK-R will be my choice 17x8.5 with -10 offset under marugen shokai flares and the new Apex coil overs. Should fit nice with lots of travel and flush looks. With VQ power I’d like to run 225/45r17 or 245/40r17 on all corners, again because staggered makes rotating tires a problem. A lot of the guys on here will tell you don’t go staggered for handling which I agree with especially if your suspension is staying mostly stock and you spend more time cruising than racing. Where I differ from some of people is that I think 17’s are a good look on the Z and modernizing the suspension even with heim joints instead of rubber bushings you can run a 225/45 or 245/40 tire without the ride being anymore harsh or fairly decent road/highways than a stock Z on taller tires.


    Compound and tread are more important for traction than width, and given you want 250hp I’m assuming a mild turbo L28 is your goal. You won’t have instant peak torque like a diesel or modern car with VVT-i, VVEL, etc. that will give 200lb-ft right off idle. Choose the rims you like for looks, the tire width you want for suspension travel and firmest, and then the tire compound and tread for performance. Depending on your hearing I’d bet you’ll be happy with 225/45r17 tires, and might actually like the look and the ability to not have to wait a few days for tires like you might have to for anything performance oriented that is 16” or less. My beater Altima got new basic fuel savers/daily 16” and I had to try 4 places in a major city before I found a place with the correct profile. 

  20. Yeah definitely sticky the video. It should be pretty helpful for those digging into the stock steering system or rebuilding it for originality or cost effectiveness. Now for those who have a really shot rack and pinion, TTT just released completely new reproduction complete and assembled steering rack. Price seems really on point too, so it may be a better option for some.

  21. Been a hot minute with work getting busy as more staff change over happens and finishing up the plumbing for the front of the garage building… oh and all the car shows which always happen on Sunday’s my one day off each week. Got the seal kit for the 8.8 and I’m waiting on the 3.7 ring gear and trak-loc to arrive. Just wanna get that all buttoned up and stuff it out of the way. And started on the front frame rails. My car suffered from rust at the sway bar bushing mounting points and those little pockets that allow you to reach the subframe bolts so I’m doing everything from the subframe mount location forward to the lower radiator core support new/custom. Still using 18ga and hoping that the car won’t fold in half at the weld when I hit a pothole. I did botch the channel in the photo by about a 1/4” on the top face so I’m gonna remeasure and try again to get it closer.

    398C304F-AF0C-4A26-AE53-F25B287BAA47.jpeg

    094E8941-3EC7-4B59-A104-FBF300C973C3.jpeg

×
×
  • Create New...