Jump to content
HybridZ

mjfawke

Members
  • Posts

    126
  • Joined

  • Last visited

  • Days Won

    1

mjfawke last won the day on January 30 2007

mjfawke had the most liked content!

Profile Information

  • Gender
    Not Telling
  • Location
    Canberra, Australia

mjfawke's Achievements

Newbie

Newbie (1/14)

2

Reputation

  1. Is still alive!

  2. XC Falcon. Haven't tried it myself. And I have a 260Z radius rod sitting in my shed that is bent 90 degree in the middle from a crash.
  3. First, check the computer for error codes. Then check the fuel pressure. Then look for an air leak. FWIW, having had two MAF's fail, they tend to go intermittent rather than give bad values. Although I have heard of them giving incorrect readings.
  4. No plan at this point. Car is coming off the road shortly for some new parts - diff, gearbox, flywheel, turbo, possibly some GTR cams. While the engine is out (broken exhaust stud), I'll R&R the rad and IC, seal all of the openings, then pull out the cardboard for a mock-up. Still trying to find the time to do a CAD/CFD mockup. There was also a good article in a recent Racecar Engineering mag showing differences in flow and pressure distribution through a radiator with ducting - the radius on the entry is very important... And yes - cobwebs. It's summer and the spiders are in full swing. There's a redback (black widow for you guys) or two under the spoiler as well.
  5. Finally - a pic of the front. Dual ducts are out, there is no need, as the feed can be taken from above the front bumper. Yes, the car is in serious need of a wash and a cut/polish.
  6. There is a big difference between downforce generation and reducing lift.
  7. Not sure where you got this idea from - we're talking about restricting airflow into the nose of the car (efficiently, otherwise the full radiator area won't be used). Yes, bonnet vents can work - but look at the air entry size and then think about how big the vents would have to be to vent that much airflow. At best, it's part of the solution. Ducting from the rad to bonnet vents is, I think, unlrealistic - there just isn't enough space to build proper ducts (certainly not in MY engine bay).
  8. I'm sure I could waste a lot more time building things which don't work... If I had known the Z had such a problem with trapped air in the engine bay, I would have used an air/water cooler instead of sticking the IC in front of the radiator. Or had the engine moved back to the firewall and routed the pipes differently so I had clearance for the factory fan. Hindsight...
  9. I haven't had time to grab pics from the front of the car yet, but just to clarify a bit, the IC sits in the opening in the radiator support panel, and there is a gap below the bottom tank of ~ 2cm. I'm thinking 2D CFD to look at the interaction of the front bumper, ducting, IC & radiator. Maybe even create a 2D CAD of the centreline of the car to play with front panel work etc. Linux -> Blender (CAD) -> Gerris Solver & Viewer. Here is a pic of the engine bay...
  10. No space for a V-config without removing the rad support panel and a major rework of the coolers. My thinking on the two ducts is that it will a smaller overall entry path into the intercooler/radiator than a single duct with only a slightly smaller entry than the intercooler size anyway. Besides which, the bumper sits right the middle and must cause turbulent flow anyway. Less air in a diverging duct should slow the air and make it work more effectively - shouldn't it? And reduce the pressure build up in the engine bay (with appropriate undertray). As background - my car overheats once air temp goes over 32C. Was 28C before I moved the number plate down onto the front spoiler and removed the grill. Main problem is I only have space for thermofans, and they just can't flow enough air. Two years ago I did water manometer testing and the only high-pressure areas were in front of the intercooler and the 2cm gap in front of the radiator below the intercooler. I've been sitting on the issue for two years, because I haven't had time to do anything constructive about it, and didn't want to blow $1KAu on a custom alloy rad. And I cycle to work in summer anyway... I'll dig some pics out later...
  11. A duct is an enclosed entryway to the radiator/intercooler, and in the case of what we are all looking at, needs to be smaller at the entry than the exit so that the air inlet area is reduced at the nose of the car but air still flows evenly through the core. Both your and Zr8ed's work aren't ducts, they are just blanking plates around the nose area to stop air leakage. Dragonfly has built an actual duct, but had the angles too steep with the first version and had overheating issues, so had to make the entry larger. 15 degrees is about the maximum divergence angle before flow separates on the walls... ten degrees is supposed to be safer. Two ducts with 15 degrees divergence in the walls will allow an overall smaller air entry area than one duct with the same divergence. I think you should look up the P51 radiator design and the Meredith effect if this is confusing.
  12. I'm looking at doing the reduced air intake, and a couple of thoughts. Any angle greater than 15 degrees on the duct is going to cause turbulent flow, which will reduce the effective size of the radiator as the turbulent air around the edges will have trouble going through the rad (actually, intercooler in my case). Given the space limitations, the best solution would appear to be to have two ducts, one feeding from above the front bumper, and one below, both tapered at a max of 15 degrees, and feeding the upper and lower halves of the intercooler/radiator. That way I can have the smallest air inlets without losing out on intercooler/radiator area due to turbulent flow. Thoughts? Note : this is just from eyeballing the front end, I still need to check angles from above/below the front bumper.
  13. Hi Pete! Yes - it's called 'children'. The twins are now two, so I'm starting to have a life again.
  14. I'm thinking hood (bonnet) and the lower panel. Anything higher than 10-15 degrees causes flow separation and turbulence, and according to Carrol Smith, not having a radiused entry the the air inlet duct significantly increases the chances of flow separation. Other food for thought - The Electromotive 280ZX turbo had pretty large changes in angles on the radiator inlet duct, but had internal flow guides. Subaru WRX intercooler in stock form doesn't have flow over the front of the IC core without additional flow guides.
  15. Link here. It's a paper looking at aerodynamics of the SSI Airline Saloon (1934-1935) and 260Z.
×
×
  • Create New...