Jump to content
HybridZ

Search the Community

Showing results for tags 'springs'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Technical
    • FAQs
    • Model Specific
    • V8 Z Forums
    • 6 Cylinder Z Forums
    • Other Engines
    • Engine Components
    • Body Kits & Paint
    • Windtunnel Test Results and Analysis
    • Brakes, Wheels, Suspension and Chassis
    • Drivetrain
    • Fabrication / Welding
    • Interior
    • Miscellaneous Tech
    • Trouble Shooting / General Engine
  • General
    • Announcements
    • Non Tech Board
    • New Members Forum
    • Members Projects
    • Motorsports / Events
    • Buy / Sell / Trade
    • Group Buys
    • Vendor's Forum
    • Links
    • Site Support

Blogs

  • Blog 7794
  • Blog 7796
  • Blog 7797
  • Blog 7801
  • Blog 7810
  • Blog 7821
  • Blog 7850
  • Blog 7876
  • Blog 7900
  • Blog 7903
  • Blog 7918
  • Blog 7945
  • Blog 7995
  • Blog 8097
  • Blog 8113
  • Blog 8124
  • Blog 8199
  • Blog 8217
  • Blog 8223
  • Blog 8239
  • Blog 8335
  • Blog 8424
  • Blog 8478
  • Blog 8501
  • Blog 8644
  • Blog 8751
  • Blog 8853
  • Blog 9074
  • Blog 9088
  • Blog 9095
  • Blog 9152
  • Blog 10389
  • Blog 10579
  • Blog 10681
  • Blog 10929
  • Blog 10956
  • Blog 11195
  • Blog 11737
  • Blog 11794
  • Blog 11853
  • Blog 12120
  • Blog 12435
  • Blog 12884
  • Blog 13129
  • Blog 13159
  • Blog 13200
  • Blog 13472
  • Blog 13567
  • Blog 13587
  • Blog 14207
  • Blog 14439
  • Blog 14625
  • Blog 14703
  • Blog 14909
  • Blog 14919
  • Blog 14975
  • Head Gasket for 3.1 liter stroker engine
  • Blog 15298
  • Blog 15393
  • Blog 15520
  • Blog 15602
  • Blog 15654
  • Blog 15717
  • Blog 15865
  • Blog 16224
  • Blog 16227
  • Blog 16485
  • Blog 16662
  • Blog 16809
  • Blog 16878
  • Blog 16923
  • Blog 17059
  • Blog 17103
  • Blog 17116
  • Blog 17333
  • Blog 17402
  • Blog 17506
  • Blog 18026
  • Blog 18084
  • Blog 18466
  • Blog 18819
  • Blog 19188
  • Blog 19475
  • Blog 19671
  • Blog 19685
  • Blog 20165
  • Blog 20200
  • Blog 20239
  • Blog 20330
  • Blog 20345
  • Blog 20475
  • Blog 20568
  • Blog 20611
  • Blog 20767
  • Blog 20885
  • Blog 21113
  • Blog 21316
  • Blog 21355
  • Blog 21400
  • Blog 21541
  • Blog 21630
  • Blog 21672
  • Blog 21712
  • Blog 21925
  • Blog 21950
  • Blog 22036
  • Blog 22272
  • Blog 22312
  • Blog 22331
  • Blog 23034
  • Blog 23042
  • Blog 23220
  • Blog 23246
  • Blog 23322
  • Blog 23406
  • Blog 23570
  • Blog 23700
  • Blog 23718
  • Blog 23737
  • Blog 23762
  • Blog 23794
  • Blog 23917
  • Blog 23956
  • Blog 23959
  • Blog 24064
  • Blog 24131
  • Blog 24139
  • Blog 24205
  • Blog 24221
  • Blog 24240
  • Blog 24430
  • Blog 24435
  • Blog 24495
  • Blog 24576
  • Blog 24643
  • Blog 24722
  • Blog 24770
  • Blog 24833
  • Blog 24848
  • Blog 24853
  • Blog 24872
  • Blog 25030
  • Blog 25248
  • Blog 25289
  • Blog 25373
  • Blog 25396
  • Blog 25527
  • Blog 25674
  • Blog 25853
  • Blog 25886
  • Blog 25922
  • Blog 25986
  • Blog 26129
  • Blog 26181
  • Blog 26217
  • Blog 26240
  • Blog 26247
  • Blog 26299
  • Blog 26401
  • Blog 26440
  • Blog 26559
  • Blog 26735
  • Blog 26736
  • Blog 26831
  • Blog 26844
  • Blog 26883
  • Blog 26884
  • Blog 27002
  • Blog 27028
  • Blog 27169
  • Blog 27260
  • Blog 27267
  • Blog 27307
  • Blog 27345
  • Blog 27400
  • Blog 27428
  • Blog 27452
  • Blog 27558
  • Blog 27622
  • Blog 27707
  • Blog 27735
  • Blog 27877
  • Blog 28049
  • Blog 28070
  • Blog 28199
  • Blog 28214
  • Blog 28234
  • Blog 28308
  • Blog 28320
  • Blog 28475
  • Blog 28476
  • Blog 28494
  • Blog 28657
  • Blog 28671
  • Blog 28814
  • Blog 28880
  • Blog 28923
  • Blog 28943
  • Blog 28945
  • Blog 28982
  • Blog 28993
  • Blog 29008
  • Blog 29036
  • Blog 29168
  • Blog 29412
  • Blog 29467
  • Blog 29618
  • Blog 29710
  • Blog 29759
  • Blog 29832
  • Blog 29868
  • Blog 29922
  • Blog 29950
  • Blog 30009
  • Blog 30027
  • Blog 30175
  • Blog 30182
  • Blog 30287
  • Blog 30302
  • Blog 30339
  • Blog 30443
  • Blog 30461
  • Blog 30474
  • Blog 30517
  • Blog 30556
  • Blog 30654
  • Blog 30729
  • Blog 30758
  • Blog 30773
  • Blog 30842
  • Blog 30872
  • Blog 30886
  • Blog 30989
  • Blog 31027
  • Blog 31048
  • Blog 31073
  • Blog 31109
  • Blog 31116
  • Blog 31138
  • Blog 31251
  • Blog 31307
  • Blog 31343
  • Blog 31378
  • Blog 31393
  • Blog 31432
  • Blog 31495
  • Blog 31507
  • Blog 31592
  • Blog 31626
  • Blog 31643
  • Blog 31692
  • Blog 31717
  • Blog 31760
  • Blog 31768
  • Blog 31777
  • Blog 31826
  • Blog 31851
  • Blog 31877
  • Blog 31907
  • Blog 31942
  • Blog 32009
  • Blog 32051
  • Blog 32073
  • Blog 32094
  • Blog 32111
  • Blog 32142
  • Blog 32169
  • Blog 32198
  • Blog 32250
  • Blog 32256
  • Blog 32259
  • Blog 32262
  • Blog 32291
  • Blog 32371
  • Blog 32417
  • Blog 32463
  • Blog 32515
  • Blog 32519
  • Blog 32562
  • Blog 32678
  • Blog 32695
  • Blog 32725
  • Blog 32981
  • Blog 33294
  • Blog 33517
  • Blog 33612
  • Blog 33734
  • Blog 33993
  • Blog 34018
  • Blog 34140
  • Blog 34452
  • Blog 34586
  • Blog 34855
  • Blog 35117
  • Blog 35378
  • Blog 35742
  • Blog 35956
  • Blog 36022
  • Blog 36030
  • Blog 36711
  • Blog 36997
  • Blog 37069
  • Blog 37070
  • Blog 37103
  • Blog 37166
  • Blog 37257
  • Blog 37645
  • Blog 37818
  • Blog 37954
  • Blog 38369
  • Blog 38569
  • Blog 38681
  • Blog 38923
  • Blog 38945
  • Blog 39122
  • Blog 39441
  • Blog 39494
  • Blog 39529
  • Blog 39575
  • PSL_240z's Blog
  • Phlebmaster's Blog
  • dhp123166's Blog
  • miguel240zcruz's Blog
  • dsalni's Blog
  • dsalni's Blog
  • beon's Blog

Categories

  • Configuration File Sharing
  • Drawing Files, Templates
  • Manuals, Diagrams, Guides
  • Software, Calculators
  • Other misc files

Product Groups

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 18 results

  1. I have found a few threads on this issue, but no real resolution. The front sits noticeably higher (over 1") after the installation... it appears the front didn't even drop a millimeter from stock. Springs: Eibach Lowering Kit Shocks: KYB Checks: 6305.001 springs are on the front. 6305.202 springs are on the rear. The label and part number are right-side up so you can read them. The springs are seated properly. The control arm bolts/nuts were tightened with the load of the car (not on jack stands). Does anyone have a clue as to why the front did not lower? Seems basic enough...
  2. hey guys I have a '83 280zx pretty much stock everything except for the engine stuff (turbo and intercooler). My car drives like a bowl off jello, and I wanted to buy new shocks and springs. and I'm cheap, so no super cool expensive coilover sets (beside the car doesn't run well, so I won't shell out money on a car that, after 4 years of screwing around in, still won't run well) and I don't want a car that too low for very daily driving. I found out that KYB shocks are everywhere, there is some Gabriels as well on some sites. so I guess, for basic, stock like performance, i'm covered for shocks.. but the only springs I could find is an eiback lowering kit (1 inch lower) for a lot of money ( https://www.thezstore.com/page/TZS/CTGY/classic20c01 ). if anyone aware of stock like (or mild drop) springs available anywhere? There are some AC delcos listed in a few place, but back order everywhere.. thanks! seb
  3. The springs: https://zcardepot.com/products/coil-spring-set-stock-and-lowered-240z-260z-280z?variant=21384265269361 I'm planning on installing new springs and struts and I've found this option. I don't race my car and my suspension is totally stock so far, I feel my springs and struts are fine I'm just looking to lower it. I want a 1.5 or 2" drop, I like that the springs I've linked seem linear and not progressive. They don't give much of a description of who makes these springs or where they come from though. Has anyone used them? Would you recommend them? I like the amount of drop some people get with the Tokico springs but we all know they're discontinued. I don't think I'll go the eibach route because I've been reading that they don't drop the ride height much. Also if anyone's running other brands like vogtland or STAGG etc. let me know what you think about them.
  4. As I've mentioned briefly here before, I'm nearing completion of my electric conversion on a 1977 280Z. The conversion has resulted in a significant change to the car's weight balance, and I need advice on suspension adjustments to go along with this. In lieu of the ~500 lbs L28, there is now a 120 lbs electric motor: And where the spare tire well/gas tank once was, there is ~300 lbs of batteries and battery housing: As a result, the ride height is quite high up front: The rear looks fine to me though: This car will be a daily driver around town and on freeways. I have no plans to track/autocross/etc (and would need to do a major overhaul of my battery pack to set it up for that). So I'm looking for a way to lower the front while keeping the ride comfortable for daily driving. It's been suggested that I just cut the springs up front, but others have warned that's a horrible idea. I'd rather not spend big money on a fancy setup with a ton of adjustment meant for racing that I'll never use, so is there something in between that might work better for me?
  5. Full set of BC Coilover springs for sale. One pair is 62.220.006, never installed. One pair is 62.180.005, lightly used. $50 per pair, shipped anywhere in the U.S; or $90 for all four springs shipped anywhere in the U.S. Thanks for looking.
  6. Hey guys, I just started installing my Eibach ProKit springs on my 240z. I brainlessly painted over the part numbers on the springs so I had to do a lot of research to figure out which one was which. The longer non-progressive spring is 6305.001 and goes in the front, I believe, and the progressive shorter spring is 6305.202 and goes in the rear. This is correct yes? I installed the longer non-progressive spring (what I believe to be 6305.001) on one of the front struts last night and the spring looks to be slightly bent out sideways -- i.e. it's not straight up and down. You can also see that it's not straight because the piston rod is not visibly centered within the spring. I'm not sure if it's just not seated properly or what. I did notice the spring coil ends are in the little groves in the strut cap and strut base. See the pictures below and see what you think.
  7. Hi, I'm looking for a set of springs for my 1981 280zx Turbo. I would really prefer Tokico but would consider other brands. PM or email guku416 at yahoo. Thanks
  8. I need new springs, my old (25+ year Tokicos are sagging in the rear. About all I can find to replace them are the Eibach progressive rates or the Vogtlands. Somebody please give me some pros and cons. The car is mostly street driven, LS2 powered, and a little heavier on the rear axle than the front. Thanks, Mike
  9. Hey all, I took my 240Z to the track last weekend, and because it was a bit wallowy at high speeds and had a lot of body roll, I'm now looking into changing up my spring rates. Current setup: 200 lb/in front springs 22mm front sway bar 250 lb/in rear springs no rear sway bar pretty thin RCAs on the front (18.5mm) lowered somewhat but not a ton 205/55R16 bridgestone RE-11s Koni yellow single-adjustable (rebound only) race shocks -2.0º camber front and rear 2.5º caster (can't run more until I modify bodywork or relocate strut mounts rearward) 0 toe front 1/16" total toe in rear Next steps I was initially thinking of: put thicker (30mm) RCAs back on increase spring rate to 300 front, 350 rear (or even 350F, 400R) add a rear strut brace (front has a triangulated strut brace already) However, I was reading about tender + main spring setups and they seem really interesting (To be clear, I'm using the same terms Eibach is here: helper springs: soft, just keep main springs seated at full droop. tender springs: have sufficient spring rate to impact driving under other conditions; I've noticed that some people use these terms the other way around). It sounds like it could provide a good compromise between a car that corners fairly flat and doesn't move around to much on load transitions, but still has higher ability to absorb bumps well. One setup I was thinking of was: 350# main springs in the front, with #300 tenders, yielding an ~160# effective rate until the tenders reach coil bind. And something similar in the back. But, I also see lots of downsides: it seems like with the simple shocks I'm using, you'll only be valved decently for either the soft or the firm part of the range. it seems like this setup would actually be worse than my current setup for high speed stability by reducing the effective rate in those conditions. the bump absorbing ability would only be improved when the suspension isn't already compressed, so it does nothing to help when cornering near the limit and hitting some uneven pavement, i.e. conditions where you actually want this. the sudden transition from 160# to 350# spring rate after an inch or so of compression sounds like a great way to unsettle the chassis. Anyone here have any experience experimenting with a setup like this? It sounded good on the face of it, but I'm not convinced it can work. But if it can't, then why does these setups exist? Is it just another compromise between comfort and handling, or are there actual rear-world handling benefits from a setup like this? My goals for the car are: 1: fun to drive on back roads, and okay to drive on regular streets and highways. and that performs well enough on the track that it's fun to push it to its traction limit (which it wasn't really with the high amount of roll and floatyness I got last weekend) doesn't have be super comfortable on our pothole ridden California highways, but I do want to be able to drive it fast-ish on less than perfect surfaces, so it should be compliant enough for tires to remain in contact with the road most of the time. Some pics to show the amount of roll:
  10. Like many people with the tokico lowering springs have the issue of the front binding. The first photo is the red tokico 5020F that has less than one inch of bump travel. It rode worse than solid Pogo stick. So I looked far and wide for a fix. The rear end of the car is fine, tons of travel. I got the dimensions and the tokico springs and the spring rates. I found out a few springs that fit and found that MOOG 80099 fit. But they need to be cut to match the 140lbs/in rate of the tokicos. I cut the first dead coil and 2 active coils. And if my math is right the rate is close. I will update it when it settles after a nice long drive. (11,250,000*Wire diameter^4)/(8*numberofcoils*meancoildiameter^3)=spring rate first photo: old wornout tokico 5020F second photo: side by side moog spring and tockico third photo: cut moog spring fourth photo: on the car
  11. I just installed a set of Vogtland springs, and they lowered the car an even 2". Its a little lower than i would have liked, but its alright. But i am concerned about the amount of travel it took away from the suspension. It looks like there is only about an inch left of travel before bottoming out. Is this normal?
  12. Hi, if anyone has a set of these (preferably uncut) let me know, found out Dave doesn't make these anymore!
  13. I just installed vogtland springs and stagg struts on my 71 240z the front shocks are all the way up against the bump stop I thought the VA part number was supposed to go to the front and HA was supposed to go in the back the back I can't tell if they're up against the bump stop because of the boot.
  14. I recently received a set of the new coilovers BC Racing has developed with JPN Garage. I know a few of you are anxiously awaiting yours so here are a few pictures of mine. Please note: I received mine as part of a sponsorship with the website I run which is why I have mine a bit earlier. Enjoy!
  15. I am looking to buy lowering springs for my 280Z that is riding high since it went on a diet and shed some weight. email me: jminer84@gmail.com
  16. So I have a really loud and awful sounding squeaking noise coming from my rear suspension. it is happening only when I either go over a large bump, or I accelerate. It is BY FAR worse when accelerating, its almost constant squeaking/metal on metal? screeching sound. I'm having a lot of trouble trying to narrow down what could be causing it because I recently replaced all my bushings with urethane bushings, and replaced the struts. I have tried spraying my bushings with silicone spray, but that doesn't really help. I have tried having a passenger crawl back there and see if they can narrow down the problem area while I was driving but met with no success that way. I've tried taking out all the rear interior and driving with the hatch open but that did nothing. I've tried pulling the driver's side LCA (I'm convinced its on the driver's side... at least mostly) and re-greasing and sanding down the bushings to make them fit better, but that did nothing either. What could be causing a squeak under acceleration? Which bushings should I look at? Is it possible its the springs scraping the spring perch? Is there supposed to be some kind of pad between the two? Its SO BAD when accelerating, even like 1/8th gas it will do it. But cruising and braking it is silent. Any insight would be much appreciated. I apologize if this is in the wrong section, but I figure that since I have a 280z, this issue would be specific to that car, Mods please move if this is in the wrong section.
  17. Hello from the UK! I've started to restore my rusty Datsun 206Z and having done a lot of research about suspension and coilovers I am in a bit of a pickle. Now from my understanding there are several ways of getting the Z lower. I've read through numerous threads about strut sectioning and also info on the 'screw on' McKinney (there are others) set up. However it doesn't seem to clarify how low you can go and level of adjustment with each set up. I would like to know the height adjustment and capabilities of each set up please. I plan to fit a 1JZ circa 400bhp in future but in the meantime will be running triple webers. Does this effect what front springs i should go for? What set up do you suggest? Do I get the McKinney Sleeves and camber plates then get some other coilovers to screw in? Not a fan of Meguns. We have these in UK that a lot of the drift boys use - http://www.hsdcoilovers.com/ I want my car to go this low but not this low all the time - http://www.speedhunters.com/2012/05/the-peoples-choice-sunnys-240z/ I dont know how much higher this can be adjusted from how it sits now. Using the car the odd weekend for fast road, drift and maybe the odd track day. Maybe even Nurburg. Thanks in advance
  18. Hi there, I am looking for a set of lowering springs for a 76 datsun 280z. Something that gives me a 1-1.5" drop. Eibach, Tokico etc. If anyone has some for sale or knows of where I can purchase (in stock)...please let me know. Thanks! Rich
×
×
  • Create New...