Jump to content
HybridZ

Search the Community

Showing results for tags 'Stronger transmission'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Technical
    • FAQs
    • Model Specific
    • V8 Z Forums
    • 6 Cylinder Z Forums
    • Other Engines
    • Engine Components
    • Body Kits & Paint
    • Windtunnel Test Results and Analysis
    • Brakes, Wheels, Suspension and Chassis
    • Drivetrain
    • Fabrication / Welding
    • Interior
    • Miscellaneous Tech
    • Trouble Shooting / General Engine
  • General
    • Announcements
    • Non Tech Board
    • New Members Forum
    • Members Projects
    • Motorsports / Events
    • Buy / Sell / Trade
    • Group Buys
    • Vendor's Forum
    • Links
    • Site Support

Blogs

  • Blog 7794
  • Blog 7796
  • Blog 7797
  • Blog 7801
  • Blog 7810
  • Blog 7821
  • Blog 7850
  • Blog 7876
  • Blog 7900
  • Blog 7903
  • Blog 7918
  • Blog 7945
  • Blog 7995
  • Blog 8097
  • Blog 8113
  • Blog 8124
  • Blog 8199
  • Blog 8217
  • Blog 8223
  • Blog 8239
  • Blog 8335
  • Blog 8424
  • Blog 8478
  • Blog 8501
  • Blog 8644
  • Blog 8751
  • Blog 8853
  • Blog 9074
  • Blog 9088
  • Blog 9095
  • Blog 9152
  • Blog 10389
  • Blog 10579
  • Blog 10681
  • Blog 10929
  • Blog 10956
  • Blog 11195
  • Blog 11737
  • Blog 11794
  • Blog 11853
  • Blog 12120
  • Blog 12435
  • Blog 12884
  • Blog 13129
  • Blog 13159
  • Blog 13200
  • Blog 13472
  • Blog 13567
  • Blog 13587
  • Blog 14207
  • Blog 14439
  • Blog 14625
  • Blog 14703
  • Blog 14909
  • Blog 14919
  • Blog 14975
  • Head Gasket for 3.1 liter stroker engine
  • Blog 15298
  • Blog 15393
  • Blog 15520
  • Blog 15602
  • Blog 15654
  • Blog 15717
  • Blog 15865
  • Blog 16224
  • Blog 16227
  • Blog 16485
  • Blog 16662
  • Blog 16809
  • Blog 16878
  • Blog 16923
  • Blog 17059
  • Blog 17103
  • Blog 17116
  • Blog 17333
  • Blog 17402
  • Blog 17506
  • Blog 18026
  • Blog 18084
  • Blog 18466
  • Blog 18819
  • Blog 19188
  • Blog 19475
  • Blog 19671
  • Blog 19685
  • Blog 20165
  • Blog 20200
  • Blog 20239
  • Blog 20330
  • Blog 20345
  • Blog 20475
  • Blog 20568
  • Blog 20611
  • Blog 20767
  • Blog 20885
  • Blog 21113
  • Blog 21316
  • Blog 21355
  • Blog 21400
  • Blog 21541
  • Blog 21630
  • Blog 21672
  • Blog 21712
  • Blog 21925
  • Blog 21950
  • Blog 22036
  • Blog 22272
  • Blog 22312
  • Blog 22331
  • Blog 23034
  • Blog 23042
  • Blog 23220
  • Blog 23246
  • Blog 23322
  • Blog 23406
  • Blog 23570
  • Blog 23700
  • Blog 23718
  • Blog 23737
  • Blog 23762
  • Blog 23794
  • Blog 23917
  • Blog 23956
  • Blog 23959
  • Blog 24064
  • Blog 24131
  • Blog 24139
  • Blog 24205
  • Blog 24221
  • Blog 24240
  • Blog 24430
  • Blog 24435
  • Blog 24495
  • Blog 24576
  • Blog 24643
  • Blog 24722
  • Blog 24770
  • Blog 24833
  • Blog 24848
  • Blog 24853
  • Blog 24872
  • Blog 25030
  • Blog 25248
  • Blog 25289
  • Blog 25373
  • Blog 25396
  • Blog 25527
  • Blog 25674
  • Blog 25853
  • Blog 25886
  • Blog 25922
  • Blog 25986
  • Blog 26129
  • Blog 26181
  • Blog 26217
  • Blog 26240
  • Blog 26247
  • Blog 26299
  • Blog 26401
  • Blog 26440
  • Blog 26559
  • Blog 26735
  • Blog 26736
  • Blog 26831
  • Blog 26844
  • Blog 26883
  • Blog 26884
  • Blog 27002
  • Blog 27028
  • Blog 27169
  • Blog 27260
  • Blog 27267
  • Blog 27307
  • Blog 27345
  • Blog 27400
  • Blog 27428
  • Blog 27452
  • Blog 27558
  • Blog 27622
  • Blog 27707
  • Blog 27735
  • Blog 27877
  • Blog 28049
  • Blog 28070
  • Blog 28199
  • Blog 28214
  • Blog 28234
  • Blog 28308
  • Blog 28320
  • Blog 28475
  • Blog 28476
  • Blog 28494
  • Blog 28657
  • Blog 28671
  • Blog 28814
  • Blog 28880
  • Blog 28923
  • Blog 28943
  • Blog 28945
  • Blog 28982
  • Blog 28993
  • Blog 29008
  • Blog 29036
  • Blog 29168
  • Blog 29412
  • Blog 29467
  • Blog 29618
  • Blog 29710
  • Blog 29759
  • Blog 29832
  • Blog 29868
  • Blog 29922
  • Blog 29950
  • Blog 30009
  • Blog 30027
  • Blog 30175
  • Blog 30182
  • Blog 30287
  • Blog 30302
  • Blog 30339
  • Blog 30443
  • Blog 30461
  • Blog 30474
  • Blog 30517
  • Blog 30556
  • Blog 30654
  • Blog 30729
  • Blog 30758
  • Blog 30773
  • Blog 30842
  • Blog 30872
  • Blog 30886
  • Blog 30989
  • Blog 31027
  • Blog 31048
  • Blog 31073
  • Blog 31109
  • Blog 31116
  • Blog 31138
  • Blog 31251
  • Blog 31307
  • Blog 31343
  • Blog 31378
  • Blog 31393
  • Blog 31432
  • Blog 31495
  • Blog 31507
  • Blog 31592
  • Blog 31626
  • Blog 31643
  • Blog 31692
  • Blog 31717
  • Blog 31760
  • Blog 31768
  • Blog 31777
  • Blog 31826
  • Blog 31851
  • Blog 31877
  • Blog 31907
  • Blog 31942
  • Blog 32009
  • Blog 32051
  • Blog 32073
  • Blog 32094
  • Blog 32111
  • Blog 32142
  • Blog 32169
  • Blog 32198
  • Blog 32250
  • Blog 32256
  • Blog 32259
  • Blog 32262
  • Blog 32291
  • Blog 32371
  • Blog 32417
  • Blog 32463
  • Blog 32515
  • Blog 32519
  • Blog 32562
  • Blog 32678
  • Blog 32695
  • Blog 32725
  • Blog 32981
  • Blog 33294
  • Blog 33517
  • Blog 33612
  • Blog 33734
  • Blog 33993
  • Blog 34018
  • Blog 34140
  • Blog 34452
  • Blog 34586
  • Blog 34855
  • Blog 35117
  • Blog 35378
  • Blog 35742
  • Blog 35956
  • Blog 36022
  • Blog 36030
  • Blog 36711
  • Blog 36997
  • Blog 37069
  • Blog 37070
  • Blog 37103
  • Blog 37166
  • Blog 37257
  • Blog 37645
  • Blog 37818
  • Blog 37954
  • Blog 38369
  • Blog 38569
  • Blog 38681
  • Blog 38923
  • Blog 38945
  • Blog 39122
  • Blog 39441
  • Blog 39494
  • Blog 39529
  • Blog 39575
  • PSL_240z's Blog
  • Phlebmaster's Blog
  • dhp123166's Blog
  • miguel240zcruz's Blog
  • dsalni's Blog
  • dsalni's Blog
  • beon's Blog

Calendars

  • Community Calendar

Categories

  • Configuration File Sharing
  • Drawing Files, Templates
  • Manuals, Diagrams, Guides
  • Software, Calculators
  • Other misc files

Product Groups

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 1 result

  1. So i finally blew up my 2nd T5 transmission. This time locking it up solid while doing a 5th gear pull on the highway. So i figured now would be a great time to do the 240sx transmission swap I've seen from different articles. I referred alot to the following http://zhome.com/ZCMnL/tech/240SX5spd/transmission.htm Unfortunately this write up is for the S30 chassis, and not the S130 chassis like I have. DISCLAIMER, This swap was done on a 83' 280zx Turbo Couple. It will be slightly different on the Non-turbo, and will definitely be different on the 2+2, but only in the aspect of different driveshaft flanges and lengths. As far as the machining and transmission build aspects of this, it is exactly the same. Where it starts to differ however is once you get the transmission bolted to the engine block. I will explain all of that here. So once you've got all of your machining work done, which I chose to machine my non-turbo Z bell housing to fit the 240sx countershaft bearing size, since a bigger bearing, better load distribution, etc. etc. etc. Of course while I had it all apart, I found the center plate bearing for the countershaft was shot, so I went ahead and replaced both the main shaft and countershaft bearings in the center plate. I got lucky for $75, it only needed 1 bearing in reality, and all of the synchros were in great shape along with all of the gears as well. Once you get it all bolted back up to the motor, here is where there are some slight differences in relation to the S30 The S30 requires some cross member modification to allow the transmission to mount to it, as it is 2" longer. However on the S130, you do not need to drill any holes anywhere. Remove the 240sx transmission mount, and bolt the 280zx transmission mount to the tailshaft housing. Now bolt the rear cross member up and let the transmission down. It lines up perfectly. Next is going to be the driveshaft With this being a turbo car, the T5 output shaft spline is bigger and completely different than the 240sx and non turbo Z output shaft spline. The other thing is the turbo R200 differential flange is different from a non-turbo R200. Now you could just swap the non-turbo R200 flange and have the non-turbo drive shaft shortened, but you still run into the issue of non-replaceable U-joints, and the diameter of the non-turbo drive shaft is smaller than the turbo drive shaft. I was in a pinch at the moment, and did not have a line on a non-turbo differential flange, nor did I want to wait to get one in. So what I ended up doing was having a completely new driveshaft built. It has HD replaceable and greaseable U-joints, and is the same diameter of the turbo driveshaft, and can be lengthened or shortened with ease at any time should I ever need it. My driveshaft guy can get brand new yokes with the proper output shaft splines, and can get the proper matching differential flange as well. So now I have a completely serviceable driveshaft. If anyone else here is interested in them, I will be marketing them for direct bolt in applications with no fabrication needed, especially if you are considering this swap, this will provide the least amount of headaches. Also with my calculations, we got the driveshaft length just right So once you have the driveshaft issue solved, you can move onto shifter clearance. As you can see, since the transmission is 2" longer, it moves the shifter back quite further. It was actually hitting the top of the transmission tunnel. It also now makes the stock shift boot insulator no longer line up, as well as the shift boot trim ring. If you put the shift boot trim ring in its proper orientation, the shifter will hit it when going into 2nd, 4th, and reverse and not allow proper gear engagement. So this has to be rotated 180 degrees. For now I was able to make it fit. It is a very tight fit, but with a little bit of ingenuity, you can get it in there without having to cut or sand down anything. So to make room for the new shifter clearance, you need to remove a 1" by 4" piece of metal from the top of the shifter hole in the transmission tunnel. I also took this time to install a short throw shifter. I just bought some off-brand from ebay, and so far with about 100 miles it has taken my abuse and not given up at all. Feels great as well! The stock shifter is VERY sloppy, and has ALOT more throw than the stock Z transmission shifters. The shifter also sits a few inches higher than the stock Z shifters do, but to me, it is not enough to be bothersome, I actually thing it's a little better being higher up. So back to the shift boot insulator issue. I cut a secondary hole in the stock shift boot insulator to compensate for the offset of the new shifter. I then sourced a shift boot insulator from a 92-02 Chevy Camaro, which seemed like it would get me close enough to what I was trying to achieve. I'm sure there are better options out there, but for my time constraints, I was able to make this work quite well. For proper fitment, this shift boot insulator will require some minor modification. First off, the shifter hole needs to be expanded just slightly. The shifter hole needs to be elongated slightly, enough so that it fits seamlessly over the expanding part of the shifter. All I had to do was remove the very top ring of rubber around the hole, and it fit perfectly. This can be done with a pair of very sharp scissors, or tin snips. The other issue you will run into is the Camaro insulator is a little wider than the Z transmission tunnel This causes the carpet to bow out on the sides, and also doesn't allow the center console to seat properly over the entire thing, it will sit about an inch above the mount holes. Not pictured, but if you flip the Camaro shift boot insulator over, you will see a ridge which is what would ride in the shifter hole on the Camaro and seal against the body. This ridge is what seals against the Z trans tunnel as well, so anything protruding past that on the left and right sides, can be trimmed down. A little bit of trimming with a saw-zall or a cutting wheel will do the trick. Just trim along the sides and the carpet will now sit in a better position, and also allow the center console to sit lower and be able to bolt it down as well. Because of the new offset, and the different size shifter, you will not be able to retain the Stock Z shift knob or shift boot. They were long overdue for replacement, so I got a leather shift boot on ebay, and got a weighted shift knob with the proper thread for the 240sx shifter. Bolt it all down and go for a test drive. It doesn't sit 100% flush like factory, but it will sit flush enough to not move, creak, or look like crap. Overall I'm pretty satisfied with the results. The 240sx transmission definitely feels ALOT better than the crap T5 that I had. It is built ALOT better than what they had in the 70's and early 80's. As I said earlier in this write-up, I will be offering completely serviceable bolt in drive shafts for all swaps. Whether you are doing a turbo, non turbo, 2+2, whatever it is, I can get it made and shipped to you for $500 anywhere in the Continental US. International orders will be a case by case basis. I also will offer to build your transmission so its ready to bolt in as soon as you get it back from me. If you source me a Z bell housing, and 240sx transmission, I will get all of the machine work done, and bolt it all together if it doesn't need any hard parts starting at $600 plus shipping costs back and forth. If you need me to source the transmission and bell housing for you, and other parts, it will be $1200. I am located in Texas should anyone be interested. I'd like to make this swap as easy and bolt in as possible, given the T5's are getting very hard to find, and the non turbo 5 speeds are laughable at best when you're putting down a decent amount of power. Hope this encourages more of you all to consider and possibly go through with this swap. I wish I'd have done this years ago.
×
×
  • Create New...