Jump to content
HybridZ

S30/240z Wide Flares


240zach

Recommended Posts

Thanks been searching around for a while I've heard some mixed reviews about zforce so I'm wanting to avoid going down that track.

 

Marugen Shoukai looks pretty good, heard good things about them. I can't seem to find anything on mizuno work flares though?

Edited by 240zach
Link to comment
Share on other sites

I also had great dealings with Justin at Z force. In my case, I bought a G nose which is a little more complicated obviously.  It's a great piece and it came at a great price. He's checked in with me a number of times since I purchased the G nose to make sure I like the nose still.  I would have gotten his "BAMF" flares as well but had already gotten some that were wider than standard off ebay for cheaper.  

Link to comment
Share on other sites

I'm in Australia and purchased from Oscar at jdmflares.com based in the US. Very happy with the flares and service.Good quality and fit. Resonably priced at $300 and look almost the same as your first picture but with the front flares just as wide.

 

Zforce productions never ever replied to my facebook posts, messages or emails so i wouldn't recommend them.

Link to comment
Share on other sites

I can't seem to find anything on mizuno work flares though?

http://www.mizuno-works.com/parts/index.html

The front is integrated with their g nose. I like the look of the rear flare, but can't say I'm a fan of the front. I don't know of anyone state-side that imports this kit. Try looking at some JDM importers online, I now RHD Japan can sometimes get other items if you email them. They are the ones that sell the Marugen Shoukai kit.

Link to comment
Share on other sites

Do you have any pictures of the jdmflares ones installed?

Fits like a glove. A couple of them had a chip/blister/pinhole that i just smeared some bondo into but otherwise they are perfect. Its made from a fleece instead of matting which i think makes it less brittle aswell.

post-18567-0-69546500-1391212116_thumb.jpg

post-18567-0-57958400-1391212153_thumb.jpg

post-18567-0-01255400-1391212190_thumb.jpg

Link to comment
Share on other sites

The width on the jdm flares by Oscar looks good, not so keen mizuno flare they wrap too far under the guard for me.

 

Does anyone have an image of the wide Marugen Shoukai flares on a 240z? It's hard to see how they will sit with just the flare alone.

 

 

Marugen Shoukai flares:

 

http://www.rhdjapan.com/marugen-shoukai-wide-over-fenders-zg-wide-type-nissan-s30-s31.html

 

http://www.rhdjapan.com/marugen-shoukai-rear-wide-over-fenders-standard-type-nissan-s30-s31.html

Link to comment
Share on other sites

You might just try building them yourself!

I have a 72 240Z with 6 liter LS2 and T56 6 speed.  After the engine/trans install (by Dave - (Viperredls1z), we did a 4 wheel Willwood disc brake setup from Arizona Z Car and while I was doing that, I opted for the package with 5 x 4.5" lugs which gave me the option for larger tires and wheels.  I got a set of wheels (11x17 rear and 9x17 front) and mounted Michelin 335-35/17 rears and 275-40/17 fronts.  The car originally had hand built flares, but they were poorly done and in any case did not cover the larger tires.  This gave me the perfect opportunity to do some paint and bodywork that I have been putting off.

The car is in Ralph Garza's Body shop in Roseburg, Oregon for complete body work and paint.  Check my facebook page: Datsun V8Z.

The first big project was fender flares.  I made templates out of 1/2 inch plywood that would be the outside opening of the flares.  The template radius is 1 1/2 inches larger than the tire radius.  I located the center of the template 1" above the center of the wheels/tires, allowing for a bit more suspension travel.

This weekend, Ralph and his buddy John from Portland (who has done SEMA class winners) started mocking up the flares.  They are using rigid styrofoam blocks and spray foam to construct a workable surface, then filing and sanding down to a final shape.  Hopefully this will be done this weekend, and the fiberglassing can begin.

I have included a few pictures, and there are a lot more on the Datsun V8Z facebook page.

Good luck!

 

post-855-0-20028700-1391987744_thumb.jpg

post-855-0-29350400-1391987768_thumb.jpg

post-855-0-27063300-1391987798_thumb.jpg

post-855-0-16595600-1391987838_thumb.jpg

post-855-0-80676800-1391987892_thumb.jpg

post-855-0-16137500-1391987927_thumb.jpg

Link to comment
Share on other sites

@d-philip

Do yo know if your body guys would be willing to make a mold and reproduce these flares?  I would like to see the finished product as I am looking for flares now.  I will also have the same wheel sizes on my car and most likely the same tire sizes.  I will be powered by a S/C'd LS3 that is on its' way into the chasis now. 

Link to comment
Share on other sites

@d-philip

Do yo know if your body guys would be willing to make a mold and reproduce these flares?  I would like to see the finished product as I am looking for flares now.  I will also have the same wheel sizes on my car and most likely the same tire sizes.  I will be powered by a S/C'd LS3 that is on its' way into the chasis now. 

I don't know.  I should see Ralph sometime this week and will ask him.  I'll let you know

Link to comment
Share on other sites

Please do.  I am interested to see what they turn out like.  It looks like you are keeping the Datsun lip on the fender that so many just put a rolled edge on. 

 

I talked to him today, and he didn't say he wouldn't do it, but he thinks (and I agree) that there is a pretty limited market for 240Z flares for 335/35-17 (or similar width) tires.  If he decides he will consider it, I'll let you know and put you in touch with him.

Link to comment
Share on other sites

Fits like a glove. A couple of them had a chip/blister/pinhole that i just smeared some bondo into but otherwise they are perfect. Its made from a fleece instead of matting which i think makes it less brittle aswell.

 

 

Fits like a glove. A couple of them had a chip/blister/pinhole that i just smeared some bondo into but otherwise they are perfect. Its made from a fleece instead of matting which i think makes it less brittle aswell.

 

Tell me about your wheels and tires... They're exactly what I'm looking for!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...