Jump to content
HybridZ
SeanD

Stainless steel headers, exhaust and JDM twin-pipe rear muffler

Recommended Posts

Hi.

 

a) Overall length from the top of the longest exit pipe to the beginning of the entry pipe is 670mm.

 

B) From mounting point to point is 420mm from the exterior of each mounting nut/point (400 when measuring from the inside of each point to point).

 

c) Muffler itself length is 380mm.

 

1mm = 0.0393701 inches (1" = 25.4mm) and therefore :

 

a) = 26.38"

 

B) = 16.55"

 

c) = 14.96"

 

Any further questions, please don't hesitate - happy to help.

post-26030-0-19667200-1497935617_thumb.jpg

post-26030-0-72056200-1497935637_thumb.jpg

Share this post


Link to post
Share on other sites

Latest (2017) prices attached.

 

I continue to evolve the parts and develop the range available and those parts marked '" * " are already being produced and will be available later in the year.

Hi.

 

A little bit of news and an update of my prices.

 

Unfortunately, with the way the € is performing against foreign currencies, I’ve had to readdress prices with an inevitable but modest (2.5-ish %) increase.

As a good gesture, anyone with the intention to buy can do so now (against an August delivery) and pay using the previous prices !

 

I have some parts still in stock – the rest will be available from mid-August.

 

Included now on the list are my new 280ZX parts and extra S30 rear silencer options.

 

In 2018, I’m hoping to offer a choice of S30 downpipes and also an L28ET header and downpipe.

 

Kind regards,

 

Sean

post-26030-0-87914800-1498920779_thumb.jpg

post-26030-0-20157200-1498920793_thumb.jpg

post-26030-0-97959200-1498920804_thumb.jpg

post-26030-0-10081400-1498920817_thumb.jpg

post-26030-0-91642700-1498920824_thumb.jpg

Share this post


Link to post
Share on other sites

I haven't mentioned this before but.......goodies !

 

There is no profit in this - it's just for fun so here is the range :

 

Lanyards $4

 

Iron-on embroidered patches $6 (images to follow)

 

Leather, laser-cut key-rings (choice of two shapes) $12

 

100% cotton T-shirts $14

 

Grill badges (printed resin on s-steel) $30

 

All with postage on top (if not ordering with a header/line/muffler) but I'll get them out as cheap as poss. normally no more than $12

post-26030-0-39544600-1502554960_thumb.jpg

post-26030-0-57746900-1502554973_thumb.jpg

post-26030-0-17148600-1502554983_thumb.jpg

post-26030-0-33030100-1502554991_thumb.jpg

post-26030-0-13875600-1502555023_thumb.jpg

Share this post


Link to post
Share on other sites

Hi...or theirs looks very close to mine, Fujitsubo also......or we've all gone donc the same path....! :D

 

Without knowing the bore sizes and the placing of the three bolt-holes, I can't confirm.

 

However, I can share with you what my Street-sport header flange is like for you to compare if you have the Trust header already.

post-26030-0-85598100-1502821362_thumb.jpg

post-26030-0-73924100-1502821396_thumb.jpg

Share this post


Link to post
Share on other sites

Hi guys.

 

Been a while and I'm sure that you've been as busy as I have elsewhere.

 

The last batch in August sold out within 2x months and the latest has just arrived meaning that my garage once again becomes a rich 'dump' of cardboard and stainless-steel !

 

If anyone is interested, not all was pre-paid and reserved - prices remain the same.

 

Kind regards.

003.JPG

011.JPG

019.JPG

002.JPG

024.JPG

023.JPG

026.JPG

025.JPG

014.JPG

Share this post


Link to post
Share on other sites

Hi and which do you mean ? The first two are round at 150mm and 380mm long.

 

The Street is oval :

 

Dimensions :

Entry pipe = 63mm / 2.5’’ diameter (with 67mm sleeve) 110mm long

Box = 350mm long and 240mm wide x 110mm

Exit pipe = 1x63mm / 2.5’’ diameter (200mm long)

Total length = 660mm (front of entry pipe to upper end of exit pipe)

038.JPG

Share this post


Link to post
Share on other sites

Gosh - I haven't seen this year go by - so busy.

Next batch available in January and a lot pre-sold with the current -15% discount.

I've done some tweaks here and there for better fitting, finished the Fast-Road header and produced a limited run of stainless-tubular L28ET headers.

I still haven't got around to finishing the S30 downpipes between the stock manifold and my exhaust line - that's next !

 

I did finally sit down and produce a map of clients - not too much detail as I don't want anyones' car stolen but a fun way to see how well you know your neighbours 😄 , here it is up to date* :

 

https://www.mapcustomizer.com/map/Zstory exhaust customers

*however, I might I have some of you - if so, please contact me via an PM.

Share this post


Link to post
Share on other sites

Zstory wishes all its past, current and future customers, families and friends a Happy and, above all, healthy 2019 !

I have some disappointing news to annonce – my next batch won’t be available until end-February and I’ve had to postpone production of my new L28ETurbo manifold for flange compatability issues which cost me some delays, not helped by the Christmas and New Year holiday shutdown.

I sincerely apologise for this delay of a month and invite anyone, for whom this presents a problem to contact me via PM.

Please rest assured that once they arrive, I will do my very best to expediate tham asap.

Best regards and once again, my apologies.

Sean

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×