Jump to content
HybridZ

240z and 280z parts


jkelly

Recommended Posts

I'm nearing the end of my build and have several parts I don't need. Prices include shipping unless otherwise noted. I'm located in Tehachapi CA. Local pick up is fine, too.

 

  • N47 intake manifold with EGR block off plates (from a '78 280z) - $100 + shipping
  • Urethane Spindle Pin Bushing Kit (rear LCA outer bushings only) -- $20
  • Energy Suspension polyurethane compression rod bushings -- $15
  • Red Interior Plastic Rivets, 70 - 73 240z - $5 per pack of 10 (4 packs available)
  • '76 - '78 280z ECU Kick Panel Cover - $30
  • '78 280z Restored License Plate Light - $50
  • '78 280z Relay Bracket $25
  • 280z Horn Relay (tested) - $25
  • 280z Fuel Pump Relay 25230-H7200 (tested) - $25
  • 280z A/C Relay 25230-H7200 (tested) - $25
  • 280z Inhibitor Relay 25230-H7200 (tested) - $25
  • 280z EFI Main Relay 25230-89970 (tested) $15
  • 280z Fuel Pump Control Relay 25230-89966 $15
  • 280z OEM Right Side Pillar Badge (New) - $40
  • 240z Tailight Chrome Trim - $20
  • Side Marker Lenses - $5 each + shipping
  • Rear Side Marker Light Housings - $5 each + shipping (inside has been painted white)
  • Front Side Marker Light Housing - $5 + shipping (inside has been painted white)
  • New Side Marker Rubber Seals - $20 for all
  • Side Marker Chrome Trim Pieces - $5 each + shipping
  • Front Park/Turn Signal Rubber Seals - $15
  • 240z Painted Front Sway Bar - $20 + shipping
  • 3D Printed Flexible Inner Mud Flaps - $7.50 each
  • 3D Printed Flexible 240z Steering Column Firewall Gasket - $10 each
  • 3D Printed Firewall Wiper Grommet - $5.00 each
  • Custom 3D printed grommets, seals, gaskets, inspection light lenses, chair slider knobs, seat mechanism covers, etc. Contact me.
  • 280z 2+2 NEW  sewn-molded, black, cut-pile 5-piece carpet kit - $100 + shipping (like this http://www.thezstore.com/page/TZS/PROD/classic08g06b/40-2564  )

 

20190325_192156.jpg

 

20190325_182416.jpg

20190325_182404.jpg

20190325_183533.jpg

20190325_184433.jpg

20190325_183508.jpg

20190326_151105.jpg

20190326_182014.jpg

20190325_182954.jpg

 

20190325_182446.jpg

20190325_182421.jpg

20190325_182851.jpg

20190325_182906.jpg

 

 

 

20190402_194837.jpg

20190402_194849.jpg

20190402_194905.jpg

_20190327_212104.jpg

20190331_172404.jpg

20190331_172357.jpg

20190331_172342.jpg

20190331_172337.jpg

20190331_172328.jpg

20190325_182606.jpg

Edited by jkelly
Link to comment
Share on other sites

On 3/28/2019 at 7:36 AM, Grog said:

I'll take the spindle pin bushings and side marker light rubber. 

PM sent. Let me know because I'm making a run to USPS, UPS, and FedEx tomorrow.

 

23 hours ago, theczechone said:

Pictures of the 240z chrome tail light trim?

A sale is pending, but here are some pics. The plastic studs on the back that fasten it to the tailight are broken off.

 

 

20190331_115601.jpg

20190331_115607.jpg

20190331_115556.jpg

20190331_115536.jpg

20190331_115541.jpg

20190331_115552.jpg

Link to comment
Share on other sites

  • 3 weeks later...
1 hour ago, Larry Mahanor said:

Looking for a 3 wire 240Z tachometer. Most of them are 4 wire type with a square white 4 prong connector. The 3 wire type has 3 threaded studs on the back. Larry

Larry, I'll get my old tach down tonight and take a look at it and get back to you. James

Edited by jkelly
Link to comment
Share on other sites

  • 2 weeks later...
  • 1 month later...
  • 3D Printed Flexible Inner Mud Flaps - $7.50 each 
  • 3D Printed Flexible 240z Steering Column Firewall Gasket - $10 each
  • 3D Printed Firewall Wiper Grommet - $5.00 each
  • Custom 3D printed grommets, seals, gaskets, inspection light lenses, chair slider knobs, seat mechanism covers, etc. Contact me.

Interested in The top 3. I'm unsure if I need the steering column firewall currently as my interior is gutted? I could also use quite a few interior items like the seat mechanism covers. Just any interior plastics besides the dash and glovebox really. Thanks

Edited by j1valverde
Link to comment
Share on other sites

  • 2 weeks later...
On 6/25/2019 at 12:46 PM, j1valverde said:
  • 3D Printed Flexible Inner Mud Flaps - $7.50 each 
  • 3D Printed Flexible 240z Steering Column Firewall Gasket - $10 each
  • 3D Printed Firewall Wiper Grommet - $5.00 each
  • Custom 3D printed grommets, seals, gaskets, inspection light lenses, chair slider knobs, seat mechanism covers, etc. Contact me.

Interested in The top 3. I'm unsure if I need the steering column firewall currently as my interior is gutted? I could also use quite a few interior items like the seat mechanism covers. Just any interior plastics besides the dash and glovebox really. Thanks

Hey,

 

I'll print those up for you this week if you're sure you need them. I opted to replace my steering column firewall gasket because the original was falling apart and I had the steering column off for rebuilding. I can also print custom firewall wiring grommet sizes. For example, the one I printed for the wipers has a center hole size of about 3/8 to 1/2 inch which fits my wires nicely.

 

I have a model for the seat covers. I will try to print some test ones this week and see how they turn out.

 

Let me know if you want to go ahead with the first three items and I will get those made for you.

 

Thanks,

James

Link to comment
Share on other sites

Hey thanks for responding. I realize now that I only need the steering column gasket, kick panel,  and one seat adjuster lever. I’ll hit you up on pay day since I just did a money dump on bolts a dash kit and leather items

Edited by j1valverde
Link to comment
Share on other sites

  • 3 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...