fast-datsun Posted February 23, 2010 Share Posted February 23, 2010 (edited) We just got our first new H.D.YOKES for the 350Z/G35/PU 6spd trans NOW we can make drive shafts for the VQ swaps. Up to this point you had to always use the used Nissan Yokes that were hard to find or $$$$$. The first few we will need some measurments for you to make them...MACK Edited February 24, 2010 by fast-datsun Quote Link to comment Share on other sites More sharing options...
proxlamus© Posted February 27, 2010 Share Posted February 27, 2010 We just got our first new H.D.YOKES for the 350Z/G35/PU 6spd trans NOW we can make drive shafts for the VQ swaps. Up to this point you had to always use the used Nissan Yokes that were hard to find or $$$$$. The first few we will need some measurments for you to make them...MACK Pricing sir? Quote Link to comment Share on other sites More sharing options...
Pharaohabq Posted March 1, 2010 Share Posted March 1, 2010 Pricing sir? Yeah, and Price for you to make the shaft if I provide my nissan Yoke and measurements: center of ujoint/center of ujoint. Phar Quote Link to comment Share on other sites More sharing options...
fast-datsun Posted March 1, 2010 Author Share Posted March 1, 2010 Yeah, and Price for you to make the shaft if I provide my nissan Yoke and measurements: center of ujoint/center of ujoint. Phar All new parts a shaft is $525 If you supply the Yoke $325 Our new Yoke take the RACE quality 1360 u-joint which is larger the the standard H.D. 1310 u-joints Call with your measurments we try to ship in 3-5 days or less...Please call with any questions.. Quote Link to comment Share on other sites More sharing options...
Jared Posted March 1, 2010 Share Posted March 1, 2010 All new parts a shaft is $525 If you supply the Yoke $325 Our new Yoke take the RACE quality 1360 u-joint which is larger the the standard H.D. 1310 u-joints Call with your measurments we try to ship in 3-5 days or less...Please call with any questions.. Is that for steel or aluminum? Quote Link to comment Share on other sites More sharing options...
Pharaohabq Posted March 22, 2010 Share Posted March 22, 2010 Is that for steel or aluminum? I would hope aluminnum because I can have a shaft made locally for half that price using steel. I don't think the ujoints need to be upgraded either since even boosted 350z's are fine on the stock ujoints. On my rock crawler I did upgrade the yoke and joints over stock, but I'm running 35's on that. Phar Quote Link to comment Share on other sites More sharing options...
fast-datsun Posted March 23, 2010 Author Share Posted March 23, 2010 Yes its STEEL, 1018 steel special drive shaft tubing 2.75" with high speed balance. Yes! you can get cheaper ones, but not better ...aluminum is about the same price but has to be a 4" tube to have the strength... Quote Link to comment Share on other sites More sharing options...
MadZcar Posted February 6, 2012 Share Posted February 6, 2012 (edited) This is my first post here at this forum (starting a VQ35DE swap to 77 280). I knew that this was going to be a custom drive shaft but figured I could just have a shop cut and re-balance the one out of my parts car. Is there an issue with having that done? Edited February 7, 2012 by MadZcar Quote Link to comment Share on other sites More sharing options...
Zman0690 Posted February 7, 2012 Share Posted February 7, 2012 As far as I'm aware, due to the carbon fiber DS, you can only cut the yokes and have them welded to a custom shaft. Any DS shop should be able to do this fairly quickly. Quote Link to comment Share on other sites More sharing options...
MadZcar Posted February 7, 2012 Share Posted February 7, 2012 (edited) Thanks. Yeah, I found that as I was digging deeper into EMWHYR0HEN's thread. Crappy post for me as a first sorry. Edited February 7, 2012 by MadZcar Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.