-
Posts
69 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Events
Gallery
Downloads
Store
Posts posted by swe_crazy
-
-
Have a few questions.
I have a 260Z with a Holley 390 carburetor with electric choke. I have previously only worked with dellortos and su, so Holley carburetors is new for me. Idle speed is 1500, is this normal? The engine stops below 1500. Found this post just want to have it confirmed if this is correct.My link
Do I need to replace the fuel lines/pipes all the way from the tank to the carburetor or does it work with the original size of the fuel lines/pipes?
Thanks.
-
-
Delete post, Thanks
-
Finally began to get my old car running. have done a lot of electrical wiring. The car has been standing still for 3 years but today I got it running. Had to put a damper/restriction?!? in the exhaust, want to continue to be the "good" neighbor. Sooo amazingly happy, soon it will be on the road again.
Is like music to my ears. (high idle i know)
-
Rear Disk Brake Conversion 240sx
Need help with metric bolts.
(A.) What type of bolt M10 1:25 pitch?
(B.) What type of bolt, length, fully threaded or not, what pitch???. Hope someone knows
All m10x30, 1.25
-
looking good!
Mongo
Thx
-
Rear Disk Brake Conversion 240sx
To be continued
-
Rear Disk Brake Conversion 240sx
Need help with metric bolts.
(A.) What type of bolt M10 1:25 pitch?
(B.) What type of bolt, length, fully threaded or not, what pitch???. Hope someone knows
-
I've had a pair on the front of my Z for the last 10 years. It's important you drill a hole in your control arms, and tap and add a zerk fitting so you can grease them on the car.
I think that's what has made mine last so long with out wearing out.
good idea, do you have pictures of it?
-
Has anyone tried these? From MSA
http://www.thezstore...ZS/PROD/23-4170
Edited your thread title. Please describe whats in your thread from now on.
thanks - j.
-
Has anyone tried these? From MSA
-
New springs front
10mm
approximately one and a half inches between the fender and tire
finally finished installing all the springs, first and last time I do this
Camera phone photos as usual
-
Yes.
Tire choice has little to do with springs. Run whatver tire you want and yes you can use spacer as long as you can get the lugs nut on correctly.
Thx
-
Has bought the Eibach springs and searched this forum and found this.
6305.202: REAR install right side up so part # 's and Logo are facing up so you-can read it Properly.
6305.001: FRONT Same as above.
Is it correct that the spring should be placed like this? larger gap between the coils down?
Have got hold of a set Riken rims 15x7 off-set 17mm ... which means that they are very close to the spring. Do use a spacer in the front (5mm). At the rear tire is 10mm from the spring so it works but I will have to have tire 205/15 all around. But the question is whether I should have 205/50/15 or 205/60/15? with Eibach springs?
Front
Datsun 260z (early)
-
Great work! Where in sweden do you live?
Malmö
-
Did get new wheels for my car, I hope now that the 240sx calipers and discs 300ZX fits. Beginning the installation next week. Riken 15x7.
Before
After
Made a new exhaust system.
-
-
Distributor from a 280zx...rebuilt
Muffler...left
-
-
-
-
Ishound, That looks awesome.
-
Throttle is working properly, some small adjustments left
Connecting electricfan.
-
Holley 390 questions.
in Trouble Shooting / General Engine
Posted
Before I start to disassemble the carburetor, Can a vacuum leak cause this?