Jump to content
HybridZ
Phib

SK racing carburetor 45 tuning... jets....

Recommended Posts

Hello folks,

 I searched and there is really not much info in regards with these carbs.

i picked up a set of these carbs. Installed the triple and tuned. Here is current setup.

 

E88 l28

N42

Cams

triple sk carbs 45

170 air

130 main f9

50 idle jet

45 accelerator pump jet

 

The problem is im running rich during cruising, yet in wot my afr is good and when leaning of coarse it's fine.

I believe only when cruising, in which my afr is like 10.5-11.

The car feels good, but it just im like i need to gas up everytime.

 

Do you guys know or any tips i can solve this problem?

 

 

Share this post


Link to post
Share on other sites

What's your idle AFR and what's the F# of your idle jet? Both the idle and main circuit affect cruise mixture strength. I've attached Keith Franck's white paper on tuning Webers (SK is essentially the same), it should explain some things about sidedrafts that none of the tuning books nor manuals talk about.

Weber_DCOE_Tuning_White_Paper.pdf

Share this post


Link to post
Share on other sites

Interesting, I'm not familiar with that naming convention. If we assume that the 50 is the fuel orifice and 100 is air, I'm surprised at how soggy your cruise is. How many progressive holes do these carbs have?

 

Do you have pin gauges or some way of measuring small orifices? Drill bits could be a good substitute, double-check with a caliper. See if you can measure the hole diameter in the idle jet (part with 50/100 engraved in it) as well as your progression holes.

 

Also measure your float level using Keith's method and let us know what you get.

Share this post


Link to post
Share on other sites
2 hours ago, Leon said:

Interesting, I'm not familiar with that naming convention. If we assume that the 50 is the fuel orifice and 100 is air, I'm surprised at how soggy your cruise is. How many progressive holes do these carbs have?

 

Do you have pin gauges or some way of measuring small orifices? Drill bits could be a good substitute, double-check with a caliper. See if you can measure the hole diameter in the idle jet (part with 50/100 engraved in it) as well as your progression holes.

 

Also measure your float level using Keith's method and let us know what you get.

 

Im going to get more info about that when i get home.. btw, where can I buy a float tool or the optical fuel gauge seen kn kieths guide?

Share this post


Link to post
Share on other sites

Keith sells all of his stuff here: https://www.webstore.com/user,pgr,82598,owner_id,other_items

 

However, I don't think he makes the optical tool anymore. You can make one yourself using polycarbonate rod stock (I think 1/4" should work but measure your e-tube well to be sure) and a plastic sleeve. Alternatively, I've also used the depth gauge of a caliper.

Share this post


Link to post
Share on other sites
Posted (edited)

If you plan to make your own, here is a quote from Keith:
 

Quote

You'll need for the optical level measuring tool 1/4" to 5/16" clear acrylic or polycarbonate rod. The ends need to be lathe face cut with a sharp toolbit and then flame polished.

 

Use polycarbonate, as acrylic will lose its transparency after enough contact with gasoline.

Edited by Leon

Share this post


Link to post
Share on other sites
Posted (edited)

Usually a rich cruise is due to fuel level set too high.  DO NOT follow the 25mm level Keith D. Franck states. It does not work for our cars. Also do not follow his 12.5 A/F across the board.

 

Weber Spec and SK Racing/OER Spec is 29mm.

 

F2 E-Tube is your friend.

 

This page will help you out: http://240260280.com/Tech/Carbs/Weber/DCOE Theory Operation and Tuning.html

 

post-26437-14150825750279.jpg.1e4b1b51b8619a9a5a80e621ee18bcf7.jpg

 

855295514_29mmFuelLevel.thumb.jpg.1641cc5a8bdb3e6dd10700a1cab42033.jpg

 

 

Edited by Joe King

Share this post


Link to post
Share on other sites

Cool,

 

Once I receive the jets and tool. I’ll update you guys.. thanks Leon, Ryan And Joe king. Very informative.

 

I may have to reach to you all in a week.

 

What do you guys recommend for wideband? 

Im still checking my Afrs via tail pipe.

 Is there a kit I can purchase?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×