[1971 240z restoration PICS]

As far as aftermarket parts no upgrades. haven't mess with the car much it's running pretty good.

Got it tune

265hp @14 psi

322torque.

 

Most of my time is going to my other build

1971 datsun 521 truck I'm swapping a 3sge beams engine.

[took the Z to get tuned.]

Which turbo where you running? I think they are standard gap for a l28et.

Head is a stock p90a head other than solid lifters.

Shawn from Church Automotive who is a well know tuner in southern California said I could go higher but he wouldnt recommend it on 91pump gas.

He also said engine was running pretty good.

[took the Z to get tuned.]

Supra 440 injectors

 

265hp

322 lbft

@14psi

[took the Z to get tuned.]

1971 240z with L28et, ms2,edis-6 coil on plug, intake manifold similar to the senza pari group buy one,stock t3 turbo,pallnet fuel rail.

 

What guys think.... Pump gas 91 octane.

[1971 240z restoration PICS]

Installed Talbot Yorck mirrors

[Side mirrors that don't suck]

Just installed these Talbot Yorck mirrors on my Z

[1971 240z restoration PICS]

So decided to go with edis-6 since my 12-1 diyautotune stock 82 turbo dizzy was having sync problems. Now so far is much better. Also went with coil on plug.

[Is this the correct way to wire for edis&vr sensor]

Thanks Matt for the help. I all ready purchase most of the stuff to make the conversion to edis.

[Is this the correct way to wire for edis&vr sensor]

So my ms2 is already wire for vr sensor. I would need to remove q16 and wire js10 to ign and make sure no other wire is at ign. Correct?

[Is this the correct way to wire for edis&vr sensor]

Yes I bought it from diyauto tune but had it wired for direct ignition coil. But know I'm going to run edis with crank trigger wheel.

[Is this the correct way to wire for edis&vr sensor]

is this the correct way to activate EDIs on a MS2 3.0 board
The red is what needs to be done correct? On the wiring guide it says to

jumper tach select to XG1(but theres all ready jumpered tachselect to vrin) do i add another wire from tach select to xg1

Jumper opto out to tsel

But to wire the vr sensor it says to tachselect to vrin(which it is already)
wire TSEL to VROUTINV on the other section of the guide it says to wire it to opto out

 

 

[Temp Sensor]

Lower left corner on thermo housing

[1971 240z restoration PICS]

Been busy with my z. Tried it again megasquirt this time around I made it work engine is running.

[Gas at 2.67 per gallon WOW]

$2.95 in sunny southern California

[L28ET Won't Start]

.

[L28ET Won't Start]

The wires connected to the l28et coil are a blue wire for rpm gauge I believe and black plug with a black n yellow wire. That plug goes on your ignitor thats bolted on your coil bracket.

[6 ohm 25w resistors where to buy.]

I'm going to give the Honda resistor box a try. Heading to the junk yard tomorrow to get 2.

[6 ohm 25w resistors where to buy.]

Someone said to use 10w 6.8ohm resistors. Jimwolf technology sells them

[6 ohm 25w resistors where to buy.]

Would these work?

[6 ohm 25w resistors where to buy.]

I'm building my megasquirt harness I'll be using stock l28et injectors.

(82 l28et engine) Where did you guys buy the 6 ohm 25w resistors I can't seam to find them online.

[she's alive .... L28et]

No its something I put together. I should get it polished.

[she's alive .... L28et]

[AZC vs Datsun parts LLC big brake kit]

I know the actual person who makes the kit and controll arms for Datsun llc...his name is Juan krecs engineering great guy.

[Whats wrong with my tune?]

Manny are you jorge's friend?who lives few blocks from me. I think he was talking to you on the phone when he was helping me out with myl28et swap.

[grounding locations for ecu.]

I got her to start not on all cylinders though.