Jump to content
HybridZ

michez

Members
  • Posts

    21
  • Joined

  • Last visited

About michez

  • Birthday 09/18/1980

michez's Achievements

Newbie

Newbie (1/14)

10

Reputation

  1. Matt I have not had any luck with this thing. I am pretty sure that the problem is in the megasquirt. Would I be able to send it in to you guys to check it out. Michez
  2. I lived near wilkes barre, i recently moved to NYC for work but my 240 and 260z reside there tucked away in a garage, i often come in on the weekends and drive.

  3. tried moving jumpers with no luck. but I am missing c30, I desoldered c12 but the heat from my iron knocked it loose. waiting for a replacement from radio shack. should be in friday. Michez
  4. here is my MSQ it is a work in progress. 6-22-09 test.zip
  5. Attached to this file are pics of my megasquirt the only things that I have changed here are the jumpers on d1 and d2 and removed c12. I will have to run out to the garage to send my msq from my laptop.
  6. no rpm on the stim or at any time.
  7. This is how I have everything set up if anyone can read this and trouble shoot you are a god!!!!! Ms2 v3.57 jp1 set to 1 and 2 j1 set to 3 and 4 saw from pin 3 on edis to s5 terminal on the relay board pip from pin 1 on edis to tach on relay board edis module to dodge coil pack set up as ( r) -- +- (l) when holding the coil pack facing you from the proper pins on the edis module, I jumpered d1 and d2 to themselvs I removed c12 from the megasquirt as it says in the manual I don't get any rpm signal to the megasquirt with the stimulator attached, but i get spark to all plugs. I have set megatune according to the manual I have constant 12 volts to the edis, and megasquirt in the accy position and when cranking. Bolth the pip and saw are shielded, attached to the edis I believe pin7, wraped in aluminum tape and then put into plastic wire covering. every time I do "anything" I crank it over, switch the VR wires check voltages on pai and saw, and run the VR stim. always the same result. I have read an done Cygnusx1's write up for this problem and did what he said a few times with the same result I keep reading and reading, as far as I can tell it is all set up properly but no rpm signal to the megasquirt any ideas welcome. Michez
  8. I usually don't come crying for help, I can usually figure it out from reading the manual or threads/stickies. Any help at all will be greatly appreciated. Michez
  9. I believe so, it has been over a year since I ordered it. I asked Justin at Diy and he said that my unit can run edis without modifications. Michez
  10. the only thing that I have found from double checking everything is that the 25uf is not on my coil power. also reading in the manual it says not to install d1 but to put a jumper in, on my board d1 is there and also d2. I don't know if this matters. Michez
  11. yes, I get good spark with the stim hooked up I went in to megatune and double checked all of the settings and they are correct, as in the manual Michez
  12. first of all my setup 83 turbo motor edis megasquirt 2 ms2357-c set up by DIY auto tune running a map by cygnusx1 Relay board what I have done checked and double checked all connections, they are right getting 1.54 volts to the trigger sensor the coils fire when I run the audio stimulator from my laptop the pip and saw are going to there correct terminals I have switched the wires on the sensor When using the stimulator still no rpm showing I believe that the problem is in the software. Any help would be greatly appreciated, it is driving me nuts. Michez
  13. You got a great deal and you are in the right place for what you are looking for. There is a lot of knowledge floating around here these guys know these cars like there kids. But the best way to learn is to search search search and learn on your own... GOOD LUCK. Michez
  14. I was searching for a nice turbo header for my zxt and an idea came into my head, is it possible to modify a n/a 6 to 1 header to accept a t3 or t4 turbo flange and wouldn't it be far superior to the stock exhaust manifold. I had a few beers and they may be talking right now but I think it would work. Michez
  15. I have a 75 280z damper, does anyone know if it will fit the zx motor. I am not using the a/c, or power steering, only the alternator. if it fits then I could use the parts correct ?
×
×
  • Create New...