Jump to content
HybridZ

hunterzed

Members
  • Posts

    66
  • Joined

  • Last visited

About hunterzed

  • Birthday 04/28/1975

Profile Information

  • Gender
    Not Telling
  • Location
    NSW Australia

hunterzed's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. I don't know for sure but I'll ask him about the camber and offset and get back to you. I do know that he still used spacers to fit +40 offset 18"x8" rims. Not sure how big but they look like 25mm spacers. Steve
  2. Go to a toy shop that sells plastic models that you put together yourself and buy the red translucent paint that they sell. Paint it on the inside and it'll look like new. I've done this a few times when I've restored cars in the past. Works a treat.
  3. The S13 stub axle bolts straight on if you don't want to weld. I posted some pics of a mates car that he did the conversion on earlier in this thread. Gives you different choices for brakes as well.
  4. Could you do something like the LD28 intake with a water/air intercooler as part of that and would the cross member stop you using a centrally located dump pipe?
  5. I like how they have done the door handles as well. Couple of nice touches. Plenty of thought went into that car. That one of the better 280zx rear ends that I've seen done. I like it.
  6. Those last 2 are from this guy in Europe. http://speedfreak.nu/forums/gallery2.php?g2_itemId=38678 Some very clean fab work.
  7. Ducati have changed their engine from a screamer configuration to the 'BIG BANG' setup that everyone is talking about. It has to do with the balance of the bike in relation to getting the power to the ground when leaning over in the turns. As you can probably guess there is a very fine balancing act for motorbikes between when and how the power is delivered compared to the lean angle of the bike. If you can get the power down smoothly then you can start to power the bike up earlier when exiting corners. Ducati are going back to the double pulse configuration which is like having 2 V-twins bolted togeter with 2 cylinders firing at the same time as each other but I don't know about the spacing between firing of opposing pairs. There are benefits for something that is as light as a motorbike where just pushing your leg out to the side changes the roll center. However they are not doing this to gain more torque or power. They are only doing this to change the way the power is delivered and as Paul has said there are no tangible benefits to doing this in a vehicle as heavy as a car where the engine alone is nearly as heavy as a complete motorbike. Just my 2 cents.
  8. I'd be interested but only if they did a version in Kilometers as well for us guys that know how to count in metric.
  9. Well I said they just look like it. Its hard to tell when you can't actuall see how the strut attaches to the hub. I see what you mean by the rear hubs. Is there a reason (other than availability maybe) that you would just use the Z31 rear hubs?
  10. It might be an old tread but perfect timing. Thanks guys.
  11. They just look like S13 front struts with the vented disc and the Z31 rears. Thats all you need to do the conversion.
  12. I own 3 280zx's. 1 x 1980 (reciprocating ball) and 2 x 1982 (power rack and pinion). One of the later cars is off the road for a full rebuild but I have recently driven both the other cars hence can do a back to back comparison. I'm not a professional driver by any means and both of the running cars have not been freshened in the suspension for a few years. I bought all 3 cars around September last year and both running cars were tram-lining over undulations in the road surface and would wander on a straight section of road as well as being twitchy and unpredictable in the corners. Definately not like you'd expect from these cars. All I did to fix the problem was to correctly adjust the front wheel bearing pre-load and now they both drive and handle beautifully. I didn't adjust either car very much to get a big change in attitude through the steering. I checked that the rest of the steering was in good order as well. I don't notice too much difference between the two types of steering for the type of driving that I do which is as a daily driver on the road but I would say, that the rack and pinion seems to give a more confident feel through the steering wheel. This of course could be as much to do with the suspension in each car which is not identical as it has different brands of shocks but still have factory springs in each. So the test really is inconclusive unless I spend the time to change suspension on each car to get a better comparison. Not likely to happen though. If you like I can get some dimensions of the moving parts like the diameter of the main shaft and tie rod ends etc so you can compare it to the earlier S30 racks or to other racks. I won't be able to do this until I get home on Tuesday.
  13. Will these sumps fit a 81-83 280zx as well with the steering rack at the rear of the cross member?
  14. Good work guys. It'll be well recieved. Especially if you include a 280zx version of the kit too.
  15. If you're on a fairly tight budget for this then you could try something like Wax did on his RB30Dett build and get a nissan patrol sump and do a mild modification like he did. I'm sure you could get some of these over to the states for not too much and they are cheap cheap cheap here in OZ. http://forums.hybridz.org/showthread.php?t=154593
×
×
  • Create New...