daryl_db

You can go to any drive shaft shop in your area with some measurements and they will build you one suit your application. I paid 230 for mine and they had it made in less than 3 hours.

Ive got the AZC 5 lug conversion. I went with 17X8.5 with a 25 mm offset and they fit great. I am getting some rubbing in the back but I haven't rolled my fenders yet. https://www.dropbox.com/s/vhj5bo8cbcdzs4y/2015-01-10%2016.38.05.jpg?dl=0

Thank you for the reply Nullbound.

I just installed the Arizona Z Car 5 lug brake kit on my 73 240z and now Im trying to figure out what rims to get. The car has coilovers installed. I'm looking at a set of 17 X 8.5 with a 25mm offset. Will this work for both the front and rear? Please let me know what you guys with the same setup are running. Thank you Daryl

I have a set of Tokico springs for a 240. 135 shipped.

The part number for the spring are 5020. If you send me an email address then I can send you some pictures. Im located in Woodstock ga.

I have a set of Tokico springs for a 240z. They have less than 2k miles. 135 plus shipping. Let me know. Daryl

I have a new set of aftermarket fenders that are primed and ready for sanding. I shaved the front turn signal holes on each of the fenders. I believe that I also have a headlight bucket too. I'm located in Woodstock Ga.

I sent you a PM. Let me know if you want some pictures of the fenders. Thanks, Daryl

I have a new set of aftermarket fenders that have been primed and ready for blocking. I shaved the front side lights on each of the fenders already. Let me know if you are interested. I think I also have a set of buckets too. I'm located in Woodstock GA.

What year and model Z do you have? The 240z and 280z uses a different pedal assembly. Let me know. I have one for a 280Z.

I'm using a Wilwood 1 inch master cylinder hence the reason that I only need the brake booster.

I am looking for a brake booster from a 79- 81 280zx. Send me a pm with a price shipped to 30189. Thank you

Looks great. Good job!

I basically had to recreate mine. I made mine straight from the front fender to the rear of the car. From the pictures that I have seen on the net they should be straight all the way.

Post a picture of your body line and I will see if it matches mine.

I’m not sure that I would completely strip the paint off the body. I would only do it if there are signs of body damage, body work, or tons of paint. Sand the material on the car. Block everything out then work on the body lines. This will save a lot of time and money. I went to bare metal on my z but there was evidence of poor body work and tons of paint. Spend the money on good sand paper. Don't be cheap. I would strongly recommend using 3m paper. It is the best I have ever used and it lasts a lot longer than anything on the market.

I use masking tape to mark the body line. Once the masking tape is applied sand all the way to the edge of the tape and then remove the tape and apply a new tape line at the bottom on the body line and sand to that edge. This will give you a straight well-defined body line. http://www.how-to-build-hotrods.com/body-lines-straight.html

I am looking for a r200 longnose LSD differential. Let me know what you have. Thanks, Daryl Please do not waste my time if you cannot answer simple questions like: What is the gear ratio and how much are you asking.

I would be very interested if someone wants to sell their old shorties.

I will take them. Can you please send me your paypal account and I will send payment. Thanks, Daryl

That's cool. I understand that they are a pain to pull. How much shipped to 30189? Thanks, Daryl

Looking for serious sellers only.

As title states I am looking for 280z stub axles - 27 spline. If you have a set or even just 1 please let me know. Thanks, Daryl

Dec 15, 2011 Car comes off the rotisserie. I installed all of the suspension before I took I off the rotisserie so I didn’t have to lay on my back to do it. Jan 8th 2012 I decided to go with a LS1 and a T56 combo. I just bought the engine and transmission for a sweet deal. I am planning on doing so work to the engine before I install it into the car. I bought a LS6 intake, valve springs, push rods, and trying to figure out the cam I want to go with. Jan 21th 2012 I am in the body work stage at the moment. I just laid down epoxy primer on the shell. Jan 22nd 2012 I just finished with the last rust repair. I hope to have all of the panels ready for paint in the next couple of weeks. It’s very hard for me to get motivated when it’s cold in the garage. I have a heater but I think Im just being a lazy ass.