mas28O
-
Posts
660 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Events
Gallery
Downloads
Store
Posts posted by mas28O
-
-
what roll cage kit is this? I am looking for a 6pt roll cage.
Mike
-
what roll cage kit is this? I am looking for a 6pt roll cage.
Mike
-
What did everyone use for a surge tank? My fuel set up is next. My fuel line on my Lt1 are steel and the come out in the back of the motor, so I am just going to run hard line to the back.
Mike
-
my 95 Corvette motor had hard lines on it, no plastic.
-
niceguy678us, the front mount was not that hard to make. But someone should set up a install kit for the R230.
Mike
-
Let me know on cost. I would like to get this car done soon.
Thanks
Mike
-
I have the big 4L60e trans and I did not want to hammer too much.
-
The polly isolators are from a leaf spring truck (1987 Suzuki Samurai). Now I need som cv adapters, I hope Ross C is going to make them. This web site has been very helpfull for info.
Thanks
Mike
-
72 is what I am working on now, my old car was a 76 and 77
Mike
-
how do I make the pic large?
-
mount 1
[/img] -
My front mount is done, how do I post pics on here?
Thanks
Mike
-
what motor and trans do you have?
-
The 2004r should fit in the transmission tunnel the way that you have it. I test fit my motor 3 times before I had the transmission tunnel just right. I had a 77 280z before with a 2004r trans. I have a LT1/4L60e trans in a 72 and it fit without to much work.
Mike
-
Thanks Tim. Did you mount the diff center? or is it offset to the pass side?
Mike
-
I am working on the R230 for my car. I drilled the MB out to 120mm. The diff is now mounted. I need to make a new front mount for it. Does anyone have any pics of there mount?
Mike
-
I like my V8 Z-car but some of the Honda's are fast. I have a 92 civic with a 95 integra gsr motor and supercharger that made 245hp @ the wheels, runs 12.3@114 and gets 30mpg. But I like to run 10's in a Z.
Mike
-
Trace the wires back to computer and find out what plug # they goto. If you do this you can find out what they are.
Mike
-
Just use the one you got from him. It would be easy to find out where all the plugs go. I have the factory service manual if need some info.
Mike
-
I am now looking for a fuel pump on my LT1 240z. Any update on how the MSD 2225 pump is working? Or are there any other pumps to use?
Thanks
Mike
-
Ross do know when you will have the adapters? I hope you will make it like Mark's. I already have my axle cut the same as Mark's.
Thanks
Mike
-
does anyone have any info on what wires that they took out?
Mike
-
ross c, Let me know when you have the adaptors ready so I can send you some stub axles.
Mike
-
I used this info and the factory service manual to help me wire mine. I have all of the wires that I do need, but it would be nice to have some more info on what wires should be taken out. Right now my harness would work to start the motor. It only took about 2 hours, but I would like to take some of the wires out that I do not need.
thanks
Mike
Frame Replacement
in Body Kits & Paint
Posted
I just replaced my bad frame rails on my 72 240z, and at the same time I ran them all the way back. I also had to fix some holes in the floor. It looked real bad before I started but it only took 2 days and the car is alot stronger than stock now. I can now jack the car by the frame rails without bending them.
Mike