Jump to content
HybridZ

Cruzzar

Members
  • Content Count

    21
  • Joined

  • Last visited

  • Feedback

    0%

Community Reputation

0 Neutral

About Cruzzar

  • Rank
    Newbie

Profile Information

  • Location
    Visalia, Ca

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. I ordered two sets of rotors. One pair for the stock '75 Z font end and one pair for the rear Nissan Maxima upgrade. When I opened the boxes I grabbed my rear drive axles that I had apart to replace the carrier bearings and made sure the rotors fit the stud pattern. The rotors for the back fit just fine when I lined up the studs. The stock rotors for the front did not fit over the studs as I had thought they should. What I did not know is that the rotors bolt on the front hubs and do not fit over the studs as most conventional rotors do. As I posted earlier I am slowly rebuild the brake syste
  2. '82/'83 280zx non turbo, I already have them and they do fit the drive axles.
  3. I am installing the MSA/Nissan Maxima kit hence the use of rotors for the rear.
  4. I have the rear hubs apart so the stub axle is available and it definitely does not fit into the 4 holes in the rotor. The centerline distance between the opposite holes where the lug studs goes is too short ! My measurement indicates about 4 1/16". Lowrider, thanks for the clarification, I have not taken the front end apart as I have just gotten this Z from a friend who has had it stored since '94 and am replacing all the brake workings. I just jumped the gun in assuming that they fit in the conventional method. Do I have enough egg on my face?
  5. Just venting here----and trying to help out anyone else trying to order some stock, disk brake rotors for a '75 Z (or any other '70-78 plus Z). I tried ordered online stock replacement rotors for my '75 z from Rock Auto and what they sent was a rotor with a bolt circle diameter of 4.055 9 4 1/16"). The box was marked with the part number from Centric that matched their online listing number for a '75 Datsun 280z. So to return them I had to answer several questions one of which was does the part number on the box match the description that is posted online, so I went back and studie
  6. I've recently purchased a very clean 75 280 z. I want to touch up the underside of the car but I am not sure what color to use. It appears that the bottom sheet metal was painted the same as the exterior but it looks like some of the areas are black. The car's color is bronze metallic which is seen on various areas underneath (above the gas tank for example). Were the cars painted the same color top and bottom as they went down the paint line? I suspect the suspension and drive parts that are bolted onto the car after paint were a satin black. How about the wheel wells, exterior color or bla
  7. Grannyknot, sorry for the delayed response. I have been out of town and did not see your request for a supplier of EPS parts. The one that comes to mind is ePowerSteering.com – Adapting Electric Power Steering in Your Vehicle. These guys have couplers, brackets and other various parts for making installations easier. I can't recall the other company that had various parts at the moment. If it comes to me I will post it.
  8. I have the Saturn VUE eps and the Bruno controller in my other ride. I have really no complaints with the entire system. Easy wiring diagram from Bruno. I put my eps into a GM tilt column. There are several companies that now carry the correct splined couplers that help in the adaptation. I have done all the work myself and have less than $90 in the whole electrical system with a $75 swap meet column. The return to center in not particularly a problem and I get used to it after a few miles of driving. This is with the power assist turned turned down low. It is nice to be able to dial in the
  9. Here is some additional reading regarding various EPS units that may provide you with some additional information. https://www.vintage-mustang.com/threads/electric-steering-with-fail-safe-no-ebay-module-needed-pics-videos.1008722/
  10. I don't know what EPS unit that you will be using but it appears that in many adapted EPS applications the owners complain that the after installation handling or specifically the 'return to center" is not as good as was previous to the change. In various domestic applications some have even gone to 4 and 5 degrees of caster with some luck. I have a Saturn VUE EPS in my other car (53 Studebaker with aftermarket front suspension and R&P steering) and I dialed in 3 1/2 degrees of caster and I still have to manually return the wheel after going around a corner. You might want to ask if anyon
  11. So I am better informed what year did the Z go to the bubble flare.
  12. You indicated that the new stainless lines come with a double flare, are you trying to install these onto the original fittings? The original fittings are set up to receive a 'metric' iso bubble flare or am I wrong or missing something?
  13. I don't know if this is solid mount to the trans or does is use the rubber/steel isolator and if so which isolator-- the 240sx or the 280z's.
  14. I have not been able to find the specifications for the distance between the two bolts on the bottom of my 240sx transmission's rear mount. I will be putting this in my 75 280z after doing the machining operations for the front bell. I know that I will have to move the rear trans mount back but what I don't know is will the 75z's rubber/steel isolator bolt up the the Fs5w71c's two bottom trans mount bolts? I don't have access to the car for a few weeks so I can't measure the bolt centerlines on the 4 speed that is in it now.
  15. Madkaw. Does Megasquirt have the capabilities to run a knox sensor to back off the timing or does it need to with the aluminum head at 10.5 compression?
×
×
  • Create New...