Search the Community
Showing results for tags 'light'.
Found 3 results
-
Hello everybody I am currently swapping a 5.3 with a t56 into my ‘78 280z. This is my first engine swap I’ve ever done which means I’m learning as I go. I will be running a Holley terminator computer but I am now wondering how much of the old harness I can take out of the car. I plan on running speed hut gauges later down the line but my main focus is making sure my headlights, turn signals, and brake lights are working properly. I still want everything to work with the steering column but if there’s anything I’m missing please let me know.
-
So yesterday I was on my way home and my ABS light came on. This was disconcerting since it's NEVER come on before, not in the 17 years I've had the car. So I was looking into the symptoms and aside from the light, there's a hum of a motor coming from the back right rear of the car. Shutting off the car clears the ABS light temporarily, but it comes back on after a few minutes even at idle. I checked the ABS fuse and it's good, I pulled the fuse and the hum continues. I do still have brakes so that's good, but the motor noise continues even with the key off and out of the ignition. I was worried I'd run the batter down so I got a wrench and disconnected the negative cable. Today I read around a bit and it seems this is a fairly common issue we'll see more of. The ABS relay apparently can get old and get stuck. Tonight I will open the panel and rap on the relay then reconnect the power and see if the ABS pump still is humming. If so I'll pull the relay and it should from all accounts stop. If that's the case I'll order the $50 relay and be done with it. If a new relay doesn't fix the issue then it could be the wheel sensors or some other part. I'll have to break out the FSM to see how it's tested. Failing that it's a dealer diagnosis. I'd much rather do it myself than pay someone to guess at the issue. There are some savvy Z32 mechanics around, but even at Nissan, the newer mechanics have barely touched these older Z cars. I'll let you guys know what I find out and hopefully snap some pictures in the process. Phar
-
With my seating position, my small-diameter fat-ring steering wheel is blocking my tach view right in the key areas. OK for DD but already at the first autox I had to keep hunching over and was undesireably encumbered. So I'm looking to make a shift light/indicator for my 72 240Z. Still in the concept stages and any suggestions/resources/corrections are greatly appreciated; I've found a surprising lack of any information of this kind. Im aiming at passive electronics, but may consider Arduino. I'm comfortable with either but mostly just would like to figure out how such a shift light indicator would work when fitted to distributor ignitions - ie what that signal looks like coming off the coil, or similarly even just how a tachometer works in that sense. So really the key is confirming that it is a 12V square wave with frequency reflecting that of all spark plugs firing. I have a multimeter but no data collection hardware at my house. I presume its 12V at the positive terminal where the tach connects. I have a 3 ohm coil, no ballast resistor. I have an electronic dizzy but thinking about it as points seems viable and simpler, so my thinking that I'd like to verify (please correct if wrong): voltage builds in coil when the contact is closed then releases into plug when it opens. so i would think there would be 12V at the input terminal when the contactor is closed and goes to zero when it fires - thus spark signal could be considered a falling edge triggered event. Although necessary to make sure I'm thinking correctly, that level of detail isn't really functionally necessary as all we need is frequency of this signal. I could just determine the RPM I would like the light to go off at, then correct to 'revolutions per second' then multiply by 3 (inline 6 = 3 ignitions per revolution) and we have target cutoff frequency to design circuit for. Right? I havent thought through the circuitry too much yet but generally seems like it would just be: high pass filter (tweaked to frequency) --> inverter --> light (?) Arduino may have the advantage of multiple RPM set points without having to reassemble the circuit. Then just use whatever kind of light - maybe even under the windshield vents as a HUD As I said any recommendation / correction / resouce is welcomed. Thanks in advance. Ben
