kcambron

I just scrapped every small piece of undercoating off my 73 240 and I am going to just put 3 to 4 coats of Zerorust back under it. My car will only be driven in good weather and if it gets wet I'll put a fan under it untill dry. The reason I am not putting undercoating back is I want to see rust when it first starts and it will be easier to fix without all of the "tar" under there. I'll let you know in 20 years how it went!

I need front and rear, left and right seat supports for my 73 240z. Thanks, Kevin

Hello, I need front and rear seat brackets (both sides)for my 73 240z. They can just be rough cut out with a sawzall and I can clean them up.Thanks, Kevin

I started reassembling my suspension and noticed some different heights on my coil springs. I pulled the manual out and noticed the RIGHT side coil is supposed to be about 1/2" longer than the LEFT. With the driver on the left this sounds wrong. Any thoughts or info? Thanks, Kevin

I had my coil springs separated but somehow they got mixed up(one of many moves). Is there any difference front to back side to side? These all come from the same car but one is slightly longer?Any suggested lengths? Thanks, Kevin

I can't remember if my struts had the rubbers "bellows" to protect the strut cylinder. Is this needed? I notice some have them, some don't? Thanks, Kevin

Thanks, Kevin

My computer crashed and I lost most of my links, I'm looking for the essembly order for the rear stub axle. I think I'm straight except for the copper washer. Thanks, Kevin

Help! I thought I done my homework. I bought new 1981 Maxima rear Caliper brackets, 1981 280zx rotors and 1981 280zx calipers and hangers. I had the rear axle was off so I didn't need to cut the mounting bracket, fits fine. The 1981 280zx calipers do NOT fit my brackets. I read about 15 post that said they would? Thanks for the info, Kevin

I have a tank from a 1975 EFI car. It is very solid with only light rust,has sending unit, It will need to be boiled out, about $40 locally. i would take 100 or trade even for a 1973 tank. Thanks, Kevin

I'v heard how well the 75 tank fits in a 1973 z, but mine hangs down way to low and just fits poorly in every way,I'm sure it's a 75, tank could it have been an option tank that fits different?

I'v read most of the posts on fuel tank options for the l28et engine in older z cars(1973 240z).I was looking at a very clean tank I have from a 1981 zcar and think it will work if it is sectioned, remove about four inches from one side opposite of the entry hole. The strap indentions are about 1/2" to 3/4" off from my 1973 but I can work with that. Has anyone gone this route,taken any dimensions? I have a 1975 tank but it looks like the 81 tank will not hang as low(a plus to me). Thanks, Kevin

I currently have some 70's era aluminum slotted mags, but may go with the original steel wheels/caps. Thanks, Kevin

I'm starting essembly of my springs/struts and wondered if the small rubber "snubber" is neccesary on the spring? Thanks

I've spent quite a bit of time reading up on this conversion but have one question, will this combo clear my 14" wheels? 1981 Maxima brackets 82 rear rotors 81 280zx caliber Thanks, Kevin

There's a several ways that work ok, I used a high speed air drill with a 1/8" drill bit and made a series of holes around the edge of the rubber and then knocked it out with a few light blows of a hammer. The small amount of rubber that was left was cleaned up with a high speed rotary tool. I thought it was cleaner than burning them out.

I'm putting poly bushings in my mustache bar, will I need to use the original top and bottom bushings also? The ones I am talking about have small v shaped ridges on them. Kevin

Looking for a front right spindle for a 1973 240z. I'm at a stand still in my project, bail me out guys!Thanks, Kevin kcambron@semo.net

Are you looking for the rear hatch or interior trim piece? I have the rear hatch for $40 plus shipping or pickup, no rust and good condition.

Tity wity, these things don't HAVE to come out! I had mine attached to a 15,000 lb tractor and the other end to a telephone pole and almost pulled the pole down, the strut cartridge was still stuck! No joke. Good luck!

Thanks, did you use your existing front mount or the later model? Is the rubber part of the front mount the same?What about the rear cross link brace, it looks very similiar?

I found a 75 with the r200 rear end and pulled the required parts for installation in my 1973. I have done a lot of reading but am suprised to see no difference in the 1975 parts, the mustache bar seems to be the same,bolt pattern and bends,I can see no difference in the rear traverse link and the front mount looks the same as mine. Yes my car (1973)does have the 180 rear end and the 1975 car did have a r200 diff in it. What gives? Thanks, Kevin

I need a front right spindle for 1973 240z, any takers? Prefer no strut cartridge I am exausted from wrestling my other three out.

Thanks Guys, I've read tons about this subject but get lost sometime. What does the IIRC mean?Kevin