Search the Community
Showing results for tags '6 Speed'.
Found 3 results
-
Thought I would actually post my build in the project section since this is a project. As the story goes my 1995 240sx was stolen on 10/21/12. Had SR20DET S15 with the S15 6speed, Nistune ECU management. Tomei 272/272 cams. 750cc injectors, Z32 MAF. AEM tru-boost controller. Ran the J30 dif with abs sensor that I used with a Digital decoder to convert signal for the speedo. Full gauge setup last tune done on the car in July put 305 HP to the rear wheels at 15lbs of boost. Car had working A/C. Fortune 500 coilovers, Isis rear adjustable suspension. Paint and body work done in July as well, Navan front bumper, side skirts and rear valiance. Here is a dyno pull!! http://s158.photobucket.com/user/melbellwood1/media/1995%20Nissan%20240sx/20110923_162204.mp4.html Here is a run at the track!! http://s158.photobucket.com/user/melbellwood1/media/1995%20Nissan%20240sx/20120113_185224.mp4.html The gray 240 is a friend of mines, He runs deep into the 11's at the track makes 390hp runs sticky drag radials all with A/C! Car was recovered 3 days later stripped. Did not have full coverage, my stupidity. Makes ya sick. Now onto the next project. Found thru the internet in Salt Lake City Utah. Car originally bought by person when living in California. Car was originally green and repainted in the early 80’s red. Late model 1974 260Z. Car had updated DGV carbs installed. Western Star wheels and headlight covers with a rear deck louver. Car ran great for short trips to work and out. But my first road trip to a car show about 60 miles away the car overheated on the freeway cruising at 70mph. So switched out for a new radiator and thermostat. First upgrades was a twin pipe exhaust through twin glass packs. Sound is awesome. Power is limited. I was originally going do a head swap, raise the compression and run triple 2 barrels. I wanted to get 200+ hp. After driving the car for 3 months and missing the pull of a turbo, I decided to do a turbo. Didn’t help that a close friend drives a Golf daily with 400+ hp to the front wheels and owns a tuning shop. I decided from research (not deep enough to add a turbo to the 260Z motor because I am over 4 times that cost so far and still counting). Looking it over I thought with intercooler and buying all the parts that I could do this with only about $1500 out of pocket and I would have a turbo driver! HAHAHAHA..... Plans are to be a driver with some track use. Here are some of my trips to time attacks and road course racing. http://s158.photobucket.com/user/melbellwood1/media/Tooquick260z/20130216_150116_zps0eee095d.mp4.html At the point of putting the parts together and driving my car some issues started happening to the 40 year old car. The transmission that worked flawlessly started being difficult to put in first gear (after removal realized it was the slave cylinder no pressure). It developed an exhaust leak, thought it was the new exhaust that I installed. During removal of the intake realized that the #6 cylinder exhaust bolts were gone, yeah missing. Also the head gasket was leaking. I found great deals on all the parts and put them together. Turbo, ECU, AFM, wiring harness etc. Look at the boxes of parts WOW! I located a P90 head and had it rebuilt and flycut. Bought some cam tower shims from Derek, member on hear from Ocala. I put new valves from the 75-78 head with some addition spring spacers got them lined up. Before.... After.... Bolted to the head with cam timing done. Cleaned the engine compartment and painted with a few coats of clear. Looks like a deep dark hole where all the money has gone. Who’s counting right! While this was going on my brother toasted his 1993 300zx by letting the timing belt break, can you say interference. With the tranny going bad(auto) and a/c problems and other issues he decided to part it out. So, I purchased a lot of the parts from him. Breaks, Diff, MAF, Master cylinder and booster, and drive shaft to put in my Z. To put all that stuff on I purchased the rear setup from TechnoToyTuning. Nice stuff. Rear Z32 diff mounts, coilovers with Tokico’s. Old and new clutch, I should hook now!!! Handle the projected 250 HP! So since I had a 6 speed in the stolen car I decided to go with the same tranny. S15 6speed. I researched and found a few people with attempted installs of this tranny but no one had a step by step build. I posted I wanted to do this and a fellow member Xnke (Jacob) said he could help. He said to send the 6 speed with an S30 bellhousing. So I purchases a 6 Speed from JDM Tech of Orlando put them on a crate and sent to Xnke. He then cut the S30 bellhousing and mated it to the S15 6 Speed. Jacob informed me that this is actually a Mazda MX-5 6 speed. he can source and work on these tranny's! Awesome. Here are pics of taking the S30 tranny out and apart. Then with the 6 speed back ready to be installed. Znke even machined the speed access hole for the S30 speedo cable. He got the 4.11 speedo gear that will work great with the Z32 4.09 rear diff. Tranny installed and mounted in Stock tranny mount! Street T installed to run the turbo oiling line. Electric fans installed,,,, Isis 12" fans Stay tuned for the process....... -
I haven't posted here in forever it seems like. A lot of you guys have yet to be introduced to the green Z unless you've seen it on Facebook. We picked it up actually to only rob the fenders from for the red one but I've ended up falling in love. It's a hardtop car whereas the red one has a sunroof. I attempted to make a new headliner for it where the factory one was torn up. After that not much else has happened except for locating all the rust areas which, on this car, aren't actually that bad. It has been garage kept for the last couple years that I know of which has led to mostly only the floor pans being shot. the rocker panels are decent but could use some patching and a few areas in the door jam area that need some attention. As far as engine goes I've resorted back to the 2jz I have sitting around. Still working on mounts for it and am currently gathering parts, or rather money to buy parts, to start rebuilding it. Nothing spectacular out of it but maybe some GTE internals If my engine builder friend has them. Stock head for now but maybe some day switch to either a 1jz for a 1.5jz build or straight to a non vvti 2jzgte head. These are all just dreams right now and I think I'll be more than happy with a stock 2jzge in a 2500lb car. As of now all I've done is painted the valve covers, clean the block a little, and have sourced some more of the parts I'll be needing. A crankshaft from an sc300 and also a wiring harness and ecu from an SC. After that all that's left is a rebuild kit with gaskets and bearings and such. Also gonna go ahead and replace the water and oil pumps while the engine is out. Suspension I'm leaning towards the T3 DIY coilover kit or maybe just some of the mr2 struts with stiffer springs. Wheels will be some of the diamond racing wheels for now but in the end is a secret . Let's just say I'll be looking into doing a 5 lug swap soon as well. Still looking into a cd009 transmission swap but I may just throw a w58 on the 2jz and get it in the car. Maybe I'll actually be able to provide updates for this thread pretty quick. I enrolled in my local technical college for their electrician/ commercial wiring class and will be done about summer time next year. I'm kinda excited about that but who needs eduaction when you have a Z car. LMAO. Thanks guys
-
So I saw youtube video of a guy with the diesel om606 motor in it, and after a lot of searching I cannot find a clean cut manual transmission swap. I did see someone on here was trying to swap in a 300zxtt tranny to the mercedes motor, can anyone help or have some insight as to how to go about getting a manual tranny on the motor. I'm sure eventually their will be more questions about custom engine mounts and all of that, but that will be far down the road.
