Jump to content
HybridZ

RedNeckZ

Members
  • Posts

    281
  • Joined

  • Last visited

  • Days Won

    3

RedNeckZ last won the day on September 7 2010

RedNeckZ had the most liked content!

About RedNeckZ

  • Birthday 05/31/1955

Contact Methods

  • Website URL
    http://www.geocities.com/daydreamer1002001
  • Yahoo
    Daydreamer1002001@yahoo.com

Profile Information

  • Gender
    Male
  • Location
    Fayetteville, NC
  • Interests
    SCCA - road racing and autocross

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

RedNeckZ's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. If you still need a L28 block and head? I have 5 blocks and 4 heads, blocks are all L-28's and heads are a mixed bunch. You would have to come here (Fayetteville, NC) to pick-up. Also have some 5 speeds (if needed). Just let me know if you do.
  2. Have to ask. Did you remove the pressure valve in the rear of the car? It sounds like if you still have it on the car. I had to remove it to get enough pressure to the rear brakes to work. I am running the 300zx brakes on the front and the 280zx brakes on the back. If you have, the things they ask you to do should have worked. I also have racing brake lines on the front and Nissan stock brake lines (rubber) on the rear. Some people have added an adjustable brake reg. devices on it. Because some times, without it you can lock the rears up faster then the fronts. If you have already done this, just disregard this message.
  3. For front fitment if you can not find parts to replace it. You can cut out the bad section and have a replacement part made for it (welding shop can help make it) and weld it in. Then seam seal everything and paint it. Good Luck with the problem. They can make it out of any material you want. Or find a replacement part for it at a pick and pull or at parts yard. I did most of my own repairs after going to a auto body course and did all of the work myself.
  4. Do you want to keep it stock or do you mind modifying it for tire fitment. I had the same problem with my car. But I was racing it in SCCA B street prepared. I did this for bigger tire fitment. What you can do, if you want to modify it, is buy a stainless steel wheel cover off of a car trailer. You can get them from a farm sales place or even a place like Lowes. You have to cut the cars wheel well along the seam between the two halves and undo the outer wheel well seam (spot welds). After you get it out, you fit (cut to fit) the stainless steel wheel to fit that half of the wheel well. Take your time and weld it in. After that you seam seal every thing both inside and out. Then paint it to seal it and keep it from rusting again. If you want to stay stock, I hope someone can answer that one for you. One other thing you should do is to make sure to put the rim of the stainless fender against the outer fender and seam sealer it to the outer fender, do not weld it. Also a good time to seal the wheel well from rust as the Datsun did not come with any type of this. Good Luck! This is for rear fitment? You didn't say front or rear wheel well.
  5. If you can come to NC. I have 5 of them in storage. Will not send to you. Have both models You can pick the one you want.
  6. The 280Z struts are wider (bigger shock) and a small amount longer. The 240Z struts are shorter and smaller in diameter. I have been told you can cut the tubes off the 280z and weld the 240z tube on the mount and save some weight. The 280Z springs are longer then the 240Z's. They are the springs to use if you rally or race offroad. I have gotten a 240Z with the 280Z springs on it and had to remove them. They had to put spring clamps on them to bring them down to the 240Z ride height. If you get most weld on struts like Arizona Z car, they have you cut the strut and weld on another section to replace it. It is up to you and the way you go with it.
  7. Thanks for the info. I do have a set of z32 calibers in the garage. Will give them a try.
  8. I am starting to put my second Z together. I am putting a AMC 401 (stroked) into a 1971 240Z. I will be adding 300ZX turbo brakes on both the front and rear of the car. I need some help on what caliber would you recommend on this mod? I have done the 300ZX front brakes with the s12W calibers (first Z). I know I will have to make mounting plates to use this combo. It will be mostly a track car. About the AMC 401, I have two of them from my old mud truck and I want the chance to see if I can make it work. Thanks for any help you can give.
  9. I am running the 300zx up front and 280zx early model calibers with later model rotor (short hat) on the rear. I moved the rear brake pressure (above the rear axle) over and reattached to the brake line. I run stainless steel brake hoses on the front and standard rubber brake lines on the rear. On the street I run a semi-metal on the front and standard organic pads on the rear. I do not have a adjustable valve on it. I track it a lot and haven't had a problem with it overheating on me. It gives me a very neutral feel with the brakes. So try to run a better pad up front and a lesser pad on the rear. With the old brakes (stock) I would come off the track with no brakes at all. I would have to bleed them before I could go back out on the track. Your front brakes take up most of braking action, so do as much as you can to cool them (brake cooling duct). I got my info for this a few years back from the old president of the texas club. He gave a paper out on this subject during a Z car convention. About the rear hand brake, what I did was moved the brake cable to each other side and attached. I then added a small section of small round pipe to the adjustment area, it went between the adjusting nuts and the adjusting rod. If you need a copy of that paper, just contact me and leave a address to send it to. Good Luck with it, Rich.
  10. The 300ZX rotors needed the spacer, because of the hat size. The Toyota calibers come in several different sizes. You can use the S-12W, S-12-8 or the S-13W calibers to make it work. Just check this site for the big message about it. I have them (S-12W) on my Z car right now. I have it setup more for street then track. I have semi-metal pads in the front and stock pads (280ZX Setup in rear) in the back. I have removed the bais bar (above the rear axle) in the rear and have not added a pressure adjuster in the back. I use racing hoses up front and stock hoses in the rear. It has a very neutral feel to it and I like it. I run this in Solo II and on race tracks like Second Creek in Colorado and haven't had a problem with it. With the stock setup I would come off the track with no brakes (boiling point). I like it a lot. Can not afford the more expensive setups out there. Good Luck.
  11. Look at the floor boards and frame rails the most. Depending on your skill at body work, most every thing else is fixable. Or see if you can take some classes on the subject and see if they will let you work on it in the class. Also check for any crash problem that maybe hidden from view (frame rails and frontend crushed areas). You need a straight frame to start with. From there, all it will take is time and money to get it to what you want. Some people have spent a lot of time and money on their rides. Rust is aways there. They never came with rustproofing on it. How you want it to be (stock or modified) is what you have to ask yourself. They are a fun car to work on and modifiy. So good luck and keep us informed on how it goes
  12. I have a E-31 head that has been ported and polished. It also has bigger valves in it. Running 45mm DCOES Webers on it with a header. It is on a L-28 block with flat tops. Have a Schneider cam #270-80f in it right now. It runs pretty good on the street. Haven't had any problems with it in that area. Did have some problems with gas and sitting for a time. Had to replace the gas tank and blow out the lines. So you shouldn't have any problems with it on the street. I wish you luck with it. Rich.
  13. Thanks, Roger, Got the new IMSA kit today. Was very impressed with the fenders and spoiler. More like show quality over racing quality. If anyone needs to know if he is good or his kit is for real, feel free to contact me. I will strongly recommend him to you. It is a good kit to have. Rich Jerabek (redneckZ).
  14. How complete is the kit? and do you have the space to do it in? Other then that, go for it. Would love to see it after you get it done. I am still working on a 1999 Dodge Dakota for now. Where are you located? If you need help. I will see what I can do. Good Luck, Rich.

  15. Hey, jagster here. I bought a 250 GTO body, and have a 78 Z as a donor. Do you have any thoughts or advice on this? thanks Ron

×
×
  • Create New...