ZXRockie
-
Posts
235 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Events
Gallery
Downloads
Store
Everything posted by ZXRockie
-
Mechanical Speedo drive swap into RB25 Gearbox
ZXRockie replied to Mike Rowe's topic in Nissan RB Forum
so what was the conclusion on the topic... -
thanks brother, I'm in the search of a plate that allow the stock oil presure sensor, but not luck...
-
Nice work brotha! I notice that you are using an oil relocation plate, do you have the part number or model by any chance?
-
The gasket was a bid humid in that section, between #2 and the passenger side water gallery, compared to the rest of the gaskets and that was my theory. the rubber seals were gone and toasted. tomorrow is the day, i let you know how all went... thank you for your input.
-
sorry to burst your bubble, but it does. the front section ins like a bridge between both heads. I had replace the lower manifold seal, so wish me luck.
-
I found deposit of coolant right above my #2 cylinder intake valves. I've never seen anything like it, but I strongly believe it has to do with the lower intake manifold gaskets. what really causes this problem? because of it the #2 injector keep going bad and the car runs like it wasn't meant to. Please help me to determine the cause of this disaster, can't stand running in 5 cylinders and buying injectors is not fun.
-
what about MS, what did you used? which model?
-
I have and they do not keep the heater.
-
I know many of you have done the 240SX S13 dash into your Z. Does any one kept the heater or it is almost impossible. I'm in the middle of the proccess and I would like to see some examples, tips, recomendations or ideas. any input will help. Thank you
-
who can do the wiring around northern california? what shop do you guys recomend? I call Z car garage and they like doing the whole swap, I'm good with the mechanics I just like the electric to be done by the professionals.
-
Does anybody has pictures of the water lines in the RB25det after the greddy manifold is installed. that's what i need to see.
-
I thought you went to Venus auto in Sac. I'm half hour away from sac and I'm building a RB z.
-
I would loike some pics... Stealth-Z whre did you get you Cluster from?
-
My project has the z31 5 lug and the Modern Motor sports rear 5 lug. I bought a set of 1986 Z31 turbo / 16X7 20mm offset. since the front is push out 3/4 of an inch, on each side due to the z31 hubs I may not need spacers, but I'm debating as far as the rear wheels. has anyone use this wheels? or what offset does a 16X7 needs for the rear wheels. I just want to hear other opinons before making the move of buying spacers. pic od my little project...
-
If you are looking under 1500 try http://technotoytuning.com/ they have a killer set up, great for any daily/weekend warrior driver.
-
I'm in need of a 75-76 fuel tank. Looks like is impossible to obtain this item... can anyone guide me or does any of you has an extra laying around your garage. pm please.
-
I just took one to the junk yard on sunday... I need a 75 280Z fuel tank... badly... anybody...
-
Jonh, Do you have any pictures of an installation. how much do you ussually charge for it?
-
I bought a phone card and call them and used my "check card", again the best way. in person this guys get your order within a week to your house. -Jesus
-
your best bet is to give them a call and use your credit card... and check this site for set up...
-
throttle cable Q's for Greddy intake manifold
ZXRockie replied to streeteg's topic in Nissan RB Forum
I just said tranfers the TPS from the RB motor into the Q45 Throttle.. better...? -
throttle cable Q's for Greddy intake manifold
ZXRockie replied to streeteg's topic in Nissan RB Forum
I'm using the 240SX thtottle cable. the TPS Needs to be transfer from the RB motor. -
I'll second that... the whole set tranny and motor mounts fo around 300 bucks, very good quality. check out my gallery for pics.
-
I have a flywheel aswell, very good condition. I'll be down in LA this weekend if you want to pick it up. Just PM if interested... also I have a used stock Z32 clutch and presure plate, what else you need? PM if interested, AGain!!!
