Guest Brian260ZT Posted August 13, 2004 Share Posted August 13, 2004 Well, after 3 years of storage in the garage it's time to roll the Z out and clean it up. I wash off the layers of dust to find to my horror that there's white overspray all over the blue car. The overpray is from rattle-can paint on some furnature about 2 years ago. I can polish/buff the paint out... lots of elbow grease. My question is how to get the paint off the glass? I don't want to scratch my glass, so I 'm seeking advice. Thanks, Brian Quote Link to comment Share on other sites More sharing options...
Tim240z Posted August 13, 2004 Share Posted August 13, 2004 White vinegar, or a razor blade.... Quote Link to comment Share on other sites More sharing options...
blueovalz Posted August 13, 2004 Share Posted August 13, 2004 Steel wool works well too, but do not use a scotchbrite pad as I believe it will actuallly scratch the glass. Quote Link to comment Share on other sites More sharing options...
BillZ260 Posted August 13, 2004 Share Posted August 13, 2004 Yes, scotch brite scratches glass! Story associated, won't get in to it Quote Link to comment Share on other sites More sharing options...
Drftn280zxt Posted August 14, 2004 Share Posted August 14, 2004 steel wool works real good, just make sure it fine steel wool (small fibers). You'll be scratching for hours with a razor blade, don't take that route. AS for the body your gonna have to buff it/wet sand it maybe. Quote Link to comment Share on other sites More sharing options...
Drax240z Posted August 14, 2004 Share Posted August 14, 2004 I disagree, razorblade is about the fastest thing around for this job. Go to anyplace that sells paint supplies and pick up a razor blade in a handle. Simple windex and a razorblade will do any panel of glass on the Z in about 5 minutes. Quote Link to comment Share on other sites More sharing options...
Guest Brian260ZT Posted August 14, 2004 Share Posted August 14, 2004 Thanks for the suggestions... I'll try both and report in Brian Quote Link to comment Share on other sites More sharing options...
Guest Brian260ZT Posted August 5, 2005 Share Posted August 5, 2005 My apologies zed friends, I do have an update and great solution for this. I tried the razor-blade and windex on the windows, it was slow going since I don't want any scratches in the glass. I stopped using this method after one window. I did some digging around and picked up a bar of clay and quick detailer from Mequiars. This stuff totally cleaned up the whole car, very quickly. All overspray on the glass, trim, everywhere.. is now gone. The clay was very easy to work with. I would venture a need to add this to a FAQ somewheres. Thanks for the suggestions! Brian Quote Link to comment Share on other sites More sharing options...
Nismo280zEd Posted August 5, 2005 Share Posted August 5, 2005 yes, a razor blade will scratch the glass, my front windshield has some scratches from exactly that. I would recomend the lacquer thinner route or extremly fine steel wool. They also make glass refinishing kits at JC whitney if you need to go that route. As for the body, some wet sanding with 1500 grit should take care of it and then polish it up again. -Ed Quote Link to comment Share on other sites More sharing options...
Guest Brian260ZT Posted August 5, 2005 Share Posted August 5, 2005 All that you mention will work, but it's harsh to the car. The clay is not harsh at all, it's actually very easy to use, and took off all the overspray on the body, glass, and rubber. Anyways, I was just posting my results from my initial inquiry. Thx, Brian Quote Link to comment Share on other sites More sharing options...
datsunlover Posted August 5, 2005 Share Posted August 5, 2005 I used a razor blade w/windex and had no problems with scratching on the glass.. you have to get a feet for it and hold it just right, but it will work... cool that you found another way though! Quote Link to comment Share on other sites More sharing options...
mom'sZ Posted August 7, 2005 Share Posted August 7, 2005 Hi folks I just want to say the clay block is the bomb for overspray removal. And not just on glass, it works on the painted surface also. Like datsunlover said, you can use a razor, held in your hand, you develop a feel for it. Use the Windex as kind of a lubricant. But you could still easily gouge the glass if not super careful. Don't try it with a holder. Or like racerX said, use only super fine steel wool. These were the traditional ways to remove overspray from glass for years that I was in the business. Then one day a paint rep brought me the clay block kit. They are available now in most auto supply stores (Discount) in the car detailing area. It comes with a spray (much like windex) that simply lets the clay slid more easily over the surface. The clay block is then rubbed on the surface. It works GREAT! Buffing removes paint, you buff too hard you can go through the paint. Razors and steel wool can scratch. The clay block is totally safe. It works great for removing bugs off the front! I love it and highly recomend it. One note, don't drop the clay block. Sand and dirt will stick to it and scratch the paint next time you use it. If you do drop it, try to cut the surface that hit the ground off with a razor. And the clay block will come in a little plastic box or bag, keep it in there when not in use or a zip lock baggie or it will dry out. After you use it on a area, run you hand over it, you will be amazed how smooth the surface feels. Quote Link to comment Share on other sites More sharing options...
skipzoomie Posted August 7, 2005 Share Posted August 7, 2005 Mom'sz is absolutely correct. If you guys haven't heard of the clay block you need to investigate it. It's the greatest thing since cleaning compounds were invented. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.