Drivetrain

6103 topics in this forum

1. Driveshaft/ Propeller shaft

   By abes, August 29, 2009
   • 7 replies
   • 1.4k views
   • 
   • Ineptitude01
   • September 1, 2009

3. Gear Shift Lever issues with 71' 5-speed swap

   By NCZZZ, September 27, 2009
   • 7 replies
   • 1.3k views
   • 
   • MAG58
   • September 29, 2009

4. Halfshaft a failsafe?

   By 7MGFORCE, October 12, 2009
   • 7 replies
   • 1.1k views
   • 
   • 7MGFORCE
   • October 14, 2009

5. ACT clutch part numbers?

   By Sparks280zt, October 13, 2009
   • 7 replies
   • 1.1k views
   • 
   • cygnusx1
   • October 13, 2009

6. Loud "POP" then clackclackclack. Diff? U joint?

   By usafdarkhorse, October 27, 2009
   • 7 replies
   • 1.5k views
   • 
   • usafdarkhorse
   • November 17, 2009

7. 240sx tranny in 280zx-can I use stock driveshaft?

   By nosebleedZ, November 5, 2009
   • 7 replies
   • 1.6k views
   • 
   • nosebleedZ
   • November 8, 2009

8. R200 Side Seal

   By IdahoZ, November 21, 2009
   • 7 replies
   • 3.3k views
   • 
   • usafdarkhorse
   • January 16, 2010

9. Clutch pressure plate question/Flywheel idiocy

   By Lazyeye, December 28, 2009
   • 7 replies
   • 1.8k views
   • 
   • JMortensen
   • December 28, 2009

10. I think i understand pinion angle but I want to be sure.

    By Guest TurboHatch, January 21, 2010
    • 7 replies
    • 1.1k views
    • 
    • Guest
    • February 5, 2010

11. swapping LSD from one r200 to another open r200 question.

    By Guest TurboHatch, January 30, 2010
    • 7 replies
    • 1.2k views
    • 
    • lubu
    • January 31, 2010

12. Ron Tyler Diff Mount Question early 240

    By Dtsnlvrs, February 16, 2010
    • 7 replies
    • 2.7k views
    • 
    • ezzzzzzz
    • February 18, 2010

13. Gear swap

    By coolbeans, February 20, 2010
    • 7 replies
    • 1.9k views
    • 
    • z-ya
    • May 26, 2010

14. Kameari 3.15 Gear Set too Big?

    By rucus01, March 2, 2010
    • 7 replies
    • 1.3k views
    • 
    • rucus01
    • March 3, 2010

15. 85 300zx trans into a 75 280z

    By galloguy05, March 6, 2010
    • 7 replies
    • 3.6k views
    • 
    • F150toZ
    • September 18, 2010

16. Having a hard time.. Clutch or Torsen LSD?!

    By proxlamus©, March 25, 2010
    • 7 replies
    • 2.6k views
    • 
    • JMortensen
    • March 26, 2010

17. OBX gear flipping.

    By ModernS30, May 13, 2010
    • 7 replies
    • 1.6k views
    • 
    • cygnusx1
    • May 13, 2010

18. Troubleshooting failing clutch in 29176 280Z

    By PhilbertZ, June 7, 2010
    • 7 replies
    • 2.9k views
    • 
    • PhilbertZ
    • July 3, 2010

19. conversion u joints

    By emeraldlion, August 7, 2010
    • 7 replies
    • 1.6k views
    • 
    • deja
    • August 9, 2010

20. Correct Spec for Drive Shaft Bolts

    By LLave, September 1, 2010
    • 7 replies
    • 1.4k views
    • 
    • LLave
    • September 9, 2010

21. Lowest Geared Open R200

    By Meph, September 12, 2010
    • 7 replies
    • 1.9k views
    • 
    • 350zdriver
    • October 11, 2010

22. R200 Q45 Ring Set Question

    By redleg, September 15, 2010
    • 7 replies
    • 2.4k views
    • 
    • Snailed
    • October 18, 2010

23. Can u please help me ID this diff

    By Guest ttoude, October 4, 2010
    • 7 replies
    • 1.2k views
    • 
    • Tank
    • October 6, 2010

24. 300ZXT VS 300ZX CV axles

    By Zfan1, October 11, 2010
    • 7 replies
    • 3.9k views
    • 
    • kj280z
    • May 10, 2011

25. tranny options

    By Guest enzo210, December 11, 2010
    • 7 replies
    • 1.7k views
    • 
    • Guest
    • December 13, 2010

26. Should my clutch fork have tension on it after pulling the slave cylinder?

    By FiveSeventyZee, January 11, 2011
    • 7 replies
    • 8.2k views
    • 
    • FiveSeventyZee
    • January 31, 2011