Drivetrain

6104 topics in this forum

1. DRIVE SHAFT QUESTION FROM OKINAWA

   By Corzette, May 22, 2003
   • 1 reply
   • 753 views
   • 
   • randy 77zt
   • May 23, 2003

3. replaced r200 noise gone

   By Guest bobs302z, May 23, 2003
   • 0 replies
   • 636 views
   • 
   • Guest
   • May 23, 2003

4. Quaife group buy options

   By Forrest, May 16, 2003
   • 9 replies
   • 3.1k views
   • 
   • Forrest
   • May 23, 2003

5. Slave cylinder differences

   By jgkurz, May 20, 2003
   • 2 replies
   • 903 views
   • 
   • jgkurz
   • May 22, 2003

6. WTB: Quaife for r180 or R200

   By Guest Ian turbo240, May 20, 2003
   • 2 replies
   • 877 views
   • 
   • Guest
   • May 22, 2003

7. 3.36:1 R200

   By Trevor, April 25, 2003
   • 16 replies
   • 1.7k views
   • 
   • Guest
   • May 21, 2003

8. LSD question

   By Guest cowboy6280, April 30, 2003
   • 6 replies
   • 1.5k views
   • 
   • Phantom
   • May 21, 2003

9. cool trans/diff calculator

   By j260z, May 12, 2003
   • 3 replies
   • 862 views
   • 
   • Phantom
   • May 21, 2003

10. 88 3.7 LSD install

    By 240hoke, May 20, 2003
    • 2 replies
    • 1.3k views
    • 
    • Phantom
    • May 21, 2003

11. r200 LSD and Non LSD gear set compatability????

    By stony, May 18, 2003
    • 14 replies
    • 3k views
    • 
    • RB26powered74zcar
    • May 21, 2003

12. Turbo Clutch in N/A ?

    By Guest EnthuZiast, May 21, 2003
    • 0 replies
    • 594 views
    • 
    • Guest
    • May 21, 2003

13. shoulda studied harder in math

    By stony, May 20, 2003
    • 6 replies
    • 926 views
    • 
    • stony
    • May 20, 2003

14. Gear Ratio questions

    By Guest angryAJmonotone, May 19, 2003
    • 2 replies
    • 711 views
    • 
    • j260z
    • May 19, 2003

15. Needed lsd for my 86 300zxT

    By Guest 1SickZ, May 19, 2003
    • 1 reply
    • 630 views
    • 
    • BRAD D
    • May 19, 2003

16. OK, Ford Vs. Chevy T5's...

    By strotter, May 18, 2003
    • 2 replies
    • 934 views
    • 
    • Guest
    • May 19, 2003

17. Clutch Problem,This is Bad!

    By Guest Tom Scala, May 16, 2003
    • 2 replies
    • 723 views
    • 
    • VRJoe
    • May 17, 2003

18. tip on installing cv 280zxt shafts

    By 660Z, May 16, 2003
    • 0 replies
    • 690 views
    • 
    • 660Z
    • May 16, 2003

19. T-5 to replace 700R4, how hard?

    By JKDGabe, May 16, 2003
    • 2 replies
    • 637 views
    • 
    • Dan Juday
    • May 16, 2003

20. Short Throw Shifter for 79'Zx?

    By Guest Anonymous, May 11, 2003
    • 8 replies
    • 1.4k views
    • 
    • Guest
    • May 15, 2003

21. What is a good clutch and flywheel combo?

    By KG78Z, May 15, 2003
    • 1 reply
    • 729 views
    • 
    • fl327
    • May 15, 2003

22. Good tranny rebuild shop in Orlando for my nissan tranny ?

    By Guest 1SickZ, May 13, 2003
    • 3 replies
    • 714 views
    • 
    • 280Zen
    • May 15, 2003

23. 280ZX Clutch Options

    By Guest EnthuZiast, May 13, 2003
    • 0 replies
    • 596 views
    • 
    • Guest
    • May 13, 2003

24. making an L series z a 6 speed

    By zhins50, April 20, 2003
    • 4 replies
    • 989 views
    • 
    • Guest
    • May 13, 2003

25. R180 vs. R200 halfshafts

    By Clifton, May 13, 2003
    • 8 replies
    • 3.4k views
    • 
    • brokebolt
    • May 13, 2003

26. C-clips????

    By 660Z, May 11, 2003
    • 1 reply
    • 707 views
    • 
    • brokebolt
    • May 11, 2003