Jump to content
HybridZ

wickiewicked240z

Members
 View Profile  See their activity

  • Posts

    403

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by wickiewicked240z

  1. wickiewicked240z
    As far as aftermarket parts no upgrades. haven't mess with the car much it's running pretty good. Got it tune 265hp @14 psi 322torque. Most of my time is going to my other build 1971 datsun 521 truck I'm swapping a 3sge beams engine.
  2. wickiewicked240z
    Which turbo where you running? I think they are standard gap for a l28et. Head is a stock p90a head other than solid lifters. Shawn from Church Automotive who is a well know tuner in southern California said I could go higher but he wouldnt recommend it on 91pump gas. He also said engine was running pretty good.
  3. wickiewicked240z
    Supra 440 injectors 265hp 322 lbft @14psi
  4. wickiewicked240z
    1971 240z with L28et, ms2,edis-6 coil on plug, intake manifold similar to the senza pari group buy one,stock t3 turbo,pallnet fuel rail. What guys think.... Pump gas 91 octane.
  5. wickiewicked240z
    Installed Talbot Yorck mirrors
  6. wickiewicked240z
    Just installed these Talbot Yorck mirrors on my Z
  7. wickiewicked240z
    So decided to go with edis-6 since my 12-1 diyautotune stock 82 turbo dizzy was having sync problems. Now so far is much better. Also went with coil on plug.
  8. wickiewicked240z
    Thanks Matt for the help. I all ready purchase most of the stuff to make the conversion to edis.
  9. wickiewicked240z
    So my ms2 is already wire for vr sensor. I would need to remove q16 and wire js10 to ign and make sure no other wire is at ign. Correct?
  10. wickiewicked240z
    Yes I bought it from diyauto tune but had it wired for direct ignition coil. But know I'm going to run edis with crank trigger wheel.
  11. wickiewicked240z
    is this the correct way to activate EDIs on a MS2 3.0 board The red is what needs to be done correct? On the wiring guide it says to jumper tach select to XG1(but theres all ready jumpered tachselect to vrin) do i add another wire from tach select to xg1 Jumper opto out to tsel But to wire the vr sensor it says to tachselect to vrin(which it is already) wire TSEL to VROUTINV on the other section of the guide it says to wire it to opto out
  12. wickiewicked240z
    Lower left corner on thermo housing
  13. wickiewicked240z
    Been busy with my z. Tried it again megasquirt this time around I made it work engine is running.
  14. wickiewicked240z
    $2.95 in sunny southern California
  15. wickiewicked240z
    .
  16. wickiewicked240z
    The wires connected to the l28et coil are a blue wire for rpm gauge I believe and black plug with a black n yellow wire. That plug goes on your ignitor thats bolted on your coil bracket.
  17. wickiewicked240z
    I'm going to give the Honda resistor box a try. Heading to the junk yard tomorrow to get 2.
  18. wickiewicked240z
    Someone said to use 10w 6.8ohm resistors. Jimwolf technology sells them
  19. wickiewicked240z
    Would these work?
  20. wickiewicked240z
    I'm building my megasquirt harness I'll be using stock l28et injectors. (82 l28et engine) Where did you guys buy the 6 ohm 25w resistors I can't seam to find them online.
  21. wickiewicked240z
    No its something I put together. I should get it polished.
  22. wickiewicked240z
  23. wickiewicked240z
    I know the actual person who makes the kit and controll arms for Datsun llc...his name is Juan krecs engineering great guy.
  24. wickiewicked240z
    Manny are you jorge's friend?who lives few blocks from me. I think he was talking to you on the phone when he was helping me out with myl28et swap.
  25. wickiewicked240z
    I got her to start not on all cylinders though.
×
×
  • Create New...