subtle_driver Posted May 28, 2013 Share Posted May 28, 2013 Here is something I made to extend out from my custom made downpipe with recurculated wastegate, when installing an rb26det into a 260z at work. it sounds amazing, and looks subtle. full 3" turbo back system with dynomax strait-through muffler. takes just one minute to install or remove, full v-band mounting etc. Quote Link to comment Share on other sites More sharing options...
stony Posted May 28, 2013 Share Posted May 28, 2013 If you have access to ordering from kakimoto, this exhaust is badass and bolts in. I used it in my original rb set. It was easier to modify a pre built exhaust vs building a custom one. Kinda pricy at 900 US but if you are going to have someone make an exhaust for you this may be cheaper. I'm considering this route myself when i upgrade my current exhaust. http://www.kakimotoracing.co.jp/01-01-01_n1.html#S30 I believe the kameari header has the same header flange that the kakimoto exhaust has. http://forums.hybridz.org/topic/76006-kameari-exhaust-stainless-header/ The kakimoto JDM header will not fit USM cars. フェアレディーZ 2シーター 〈S30〉 エンジン型å¼ï¼šLåž‹ å¹´å¼ï¼š69/11～76/7 シリーズ 希望å°å£²ä¾¡æ ¼(ç¨ŽæŠœæœ¬ä½“ä¾¡æ ¼) 商å“コード ä¿å®‰åŸºæº–ç‰ å‚™è€ƒ 詳細 HYPER 80 レーシング ï¿¥94,500(ï¿¥90,000) NR013 競技専用å“(一般公é“使用ä¸å¯) ※1,4 詳細・在庫 エã‚ゾーストマニホールド ï¿¥99,750(ï¿¥95,000) NH003 競技専用å“(一般公é“使用ä¸å¯) ※2,3,4 詳細・在庫 ã€å‚™è€ƒå†…容】※1)柿本改 タコ足 TYPE 3 専用。(別売ã®ã‚¨ã‚ゾーストマニホールド(NH003)ã¨ã‚»ãƒƒãƒˆã§ç„¡ã‘ã‚Œã°å–付ä¸å¯ã€‚)※2)HYPER 80 レーシング 専用。(別売ã®HYPER 80 レーシング(NR013)ã¨ã‚»ãƒƒãƒˆã§ç„¡ã‘ã‚Œã°å–付ä¸å¯ã€‚)※3)å–付時ã«ã‚¯ãƒªã‚¢ãƒ©ãƒ³ã‚¹ãŒç‹ã„部分ãŒã‚ã‚‹ãŸã‚ã€å–付時ã«ã¯åŠ å·¥ãŒå¿…è¦ãªå ´åˆæœ‰ã‚Šã€‚ Quote Link to comment Share on other sites More sharing options...
noelawinslow Posted May 28, 2013 Share Posted May 28, 2013 How do some of these setups sound? I'm about to build my exhaust system but I am aiming for a high pitched scream instead of a deep rumble. Quote Link to comment Share on other sites More sharing options...
surfer.tech Posted May 29, 2013 Share Posted May 29, 2013 If you have access to ordering from kakimoto, this exhaust is badass and bolts in. I used it in my original rb set. It was easier to modify a pre built exhaust vs building a custom one. Kinda pricy at 900 US but if you are going to have someone make an exhaust for you this may be cheaper. I'm considering this route myself when i upgrade my current exhaust. http://www.kakimotoracing.co.jp/01-01-01_n1.html#S30 I believe the kameari header has the same header flange that the kakimoto exhaust has. http://forums.hybridz.org/topic/76006-kameari-exhaust-stainless-header/ The kakimoto JDM header will not fit USM cars. フェアレディーZ 2シーター 〈S30〉 エンジン型å¼ï¼šLåž‹ å¹´å¼ï¼š69/11～76/7 シリーズ 希望å°å£²ä¾¡æ ¼ (ç¨ŽæŠœæœ¬ä½“ä¾¡æ ¼) 商å“コード ä¿å®‰åŸºæº–ç‰ å‚™è€ƒ 詳細 HYPER 80 レーシング ï¿¥94,500 (ï¿¥90,000) NR013 ç«¶æŠ€å°‚ç”¨å“ (一般公é“使用ä¸å¯) ※1,4 詳細・在庫 エã‚ゾーストマニホールド ï¿¥99,750 (ï¿¥95,000) NH003 ç«¶æŠ€å°‚ç”¨å“ (一般公é“使用ä¸å¯) ※2,3,4 詳細・在庫 ã€å‚™è€ƒå†…容】 ※1)柿本改 タコ足 TYPE 3 専用。(別売ã®ã‚¨ã‚ゾーストマニホールド(NH003)ã¨ã‚»ãƒƒãƒˆã§ç„¡ã‘ã‚Œã°å–付ä¸å¯ã€‚) ※2)HYPER 80 レーシング 専用。(別売ã®HYPER 80 レーシング(NR013)ã¨ã‚»ãƒƒãƒˆã§ç„¡ã‘ã‚Œã°å–付ä¸å¯ã€‚) ※3)å–付時ã«ã‚¯ãƒªã‚¢ãƒ©ãƒ³ã‚¹ãŒç‹ã„部分ãŒã‚ã‚‹ãŸã‚ã€å–付時ã«ã¯åŠ å·¥ãŒå¿…è¦ãªå ´åˆæœ‰ã‚Šã€‚ I'm not quite sure if that will fit the Kameari header. The Drag header comes in 45 and 48mm the flange is a straight cut that flows under the firewall. If the exhaust is straight then maybe, also the Kameari is divided pipes. Depending on the length of the kakimoto exhaust it could either be too long or too short. Japanese headers are different legnths depending on brand. Quote Link to comment Share on other sites More sharing options...
subtle_driver Posted May 29, 2013 Share Posted May 29, 2013 How do some of these setups sound? I'm about to build my exhaust system but I am aiming for a high pitched scream instead of a deep rumble. your gonna want smaller dual pipes, or one pipe with no resinator and just a glasspack at the end. Quote Link to comment Share on other sites More sharing options...
Timecode Posted May 29, 2013 Author Share Posted May 29, 2013 (edited) Thanks for the response guys. I'm leaning toward stuff like this. I like the twin tip but want to see how bigger tips would like on the 240z. #2 is a S2000 but the pipe size is right. Examples: Edited May 29, 2013 by Timecode Quote Link to comment Share on other sites More sharing options...
duragg Posted May 29, 2013 Share Posted May 29, 2013 your gonna want smaller dual pipes, or one pipe with no resinator and just a glasspack at the end. Yup. That is what I have for today (going away tomorrow). 6-1 headers with MSA Twice Pipes and glass packs, nothing else. Raspy higher pitched tone that gets many compliments. Tj Quote Link to comment Share on other sites More sharing options...
noelawinslow Posted May 30, 2013 Share Posted May 30, 2013 Yup. That is what I have for today (going away tomorrow). 6-1 headers with MSA Twice Pipes and glass packs, nothing else. Raspy higher pitched tone that gets many compliments. Tj I'm running turbo, so that might change the dynamic a bit. Quote Link to comment Share on other sites More sharing options...
redlinevo7 Posted June 27, 2013 Share Posted June 27, 2013 (edited) I went twin outlet for my rb motor, had to run a fuel cell for it though. Here is my setup... Twin turbo 2.5" into 3" Flex into Single 3 to twin 2.5" muffler out with 2.5" and HKS tips. All stainless. My first muffler job and was no picnic especially working less than 2' off the ground. Edited June 27, 2013 by redlinevo7 Quote Link to comment Share on other sites More sharing options...
CarJway Posted July 1, 2013 Share Posted July 1, 2013 Got this done at Mandrel Bending Solutions in MD. Straight through Vibrant muffler sounds crisp/deep at all RPMs. These pictures are very old so don't mind the dirt/grime on the car. Quote Link to comment Share on other sites More sharing options...
mattb3562 Posted July 2, 2013 Share Posted July 2, 2013 I'm sorry to be sidetracked, but what are those lights out of Redlinevo? Badass! Quote Link to comment Share on other sites More sharing options...
LanceVance Posted July 2, 2013 Share Posted July 2, 2013 They look like Nissan Cube tails. I've read a few posts talking about using them, never seen until now. Looks much better than I had imagined! Quote Link to comment Share on other sites More sharing options...
ZT-R Posted July 3, 2013 Share Posted July 3, 2013 (edited) 4" oval pipe and 4" vibrant with 45 tip. 2,600 rpm antilag http://www.flickr.com/photos/54638216@N07/7046498645/in/set-72157625579848540 Exhaust Note without a throttle return assist spring. http://www.flickr.com/photos/54638216@N07/8284304459/in/set-72157625579848540 Edited July 3, 2013 by ZT-R Quote Link to comment Share on other sites More sharing options...
redlinevo7 Posted July 3, 2013 Share Posted July 3, 2013 @Mattb, Lance is right. Don't want to distract from op topic but my build is in the Rb engine forum. Quote Link to comment Share on other sites More sharing options...
BLOZ UP Posted July 3, 2013 Share Posted July 3, 2013 4" oval pipe and 4" vibrant with 45 tip. 2,600 rpm antilag http://www.flickr.com/photos/54638216@N07/7046498645/in/set-72157625579848540 Exhaust Note without a throttle return assist spring. http://www.flickr.com/photos/54638216@N07/8284304459/in/set-72157625579848540 What's at the front, up near the downpipe area? Is that just a collector or some type of resonator? Quote Link to comment Share on other sites More sharing options...
ZT-R Posted July 4, 2013 Share Posted July 4, 2013 In that picture its just the way the pipe is bent and all. Now i had a resonator made in 4" oval and it is right under the drive shaft. It sounded sooooo good without the resonator but it was just to loud for the streets here. Every 4th car is a cop... Quote Link to comment Share on other sites More sharing options...
9rider Posted July 6, 2013 Share Posted July 6, 2013 Here is mine - Wicked Flow. Don't laugh please , I gather all the junk part from my friend junk yard and put in my Z. Don't really think to start the project yet. I wouldn't change if it wasn't rust thru. Quote Link to comment Share on other sites More sharing options...
mattb3562 Posted August 5, 2013 Share Posted August 5, 2013 Loved the look, so I had to steal it....sorry BLOZ UP. Lol Quote Link to comment Share on other sites More sharing options...
Reverend Posted August 13, 2013 Share Posted August 13, 2013 (edited) I dont know if thread already exists but it would be awesome to hear your custom exhaust notes.. Edited August 13, 2013 by Reverend Quote Link to comment Share on other sites More sharing options...
BLOZ UP Posted August 13, 2013 Share Posted August 13, 2013 Loved the look, so I had to steal it....sorry BLOZ UP. Lol Eh? Yours looks like someone else's more than mine? Plus, I've fixed mine so it has legit hangars and hugs the body now. Don't seem to have pics. I dont know if thread already exists but it would be awesome to hear your custom exhaust notes.. Maybe someone should start a thread. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.