Milenko2121 Posted June 30, 2016 Share Posted June 30, 2016 (edited) Just an update Had these for close to a year and a half now. Shocks still feel the same, car is still the same height as when i last posted in july last year. Feel nice on canyon roads and over bumps too. Edited June 30, 2016 by Milenko2121 Quote Link to comment Share on other sites More sharing options...
CarolinaTZ Posted August 29, 2016 Share Posted August 29, 2016 (edited) Thanks guys....this thread has been helpful. I want to order the Vogtland springs for a late 260Z/280Z from Brandcarparts. I assume the photo on their website is incorrect (smaller at one end and progressive wound). http://brandcarparts.com/1975-1978-nissan-datsun-280z-vogtland-lowering-springs-kit-1-25-drop.html The picture on this ebay listing looks correct (no taper and linear wound). http://www.ebay.com/itm/VOGTLAND-GERMAN-LOWERING-SPRINGS-fits-NISSAN-DATSUN-260Z-280Z-1975-to-77-1978-/400786161518?fits=Make%3ADatsun%7CModel%3A260Z&hash=item5d50b77f6e:g:-uQAAOSwDN1UNiMy&vxp=mtr Are these the ones Brandcarparts send even though their web picture is different? Can any of you 280Z Vogtland spring owners confirm? Also, I plan to buy struts.....would Tokico Illuminas be worth the added cost as opposed to HPs? Edited August 29, 2016 by CarolinaTZ Quote Link to comment Share on other sites More sharing options...
Milenko2121 Posted August 30, 2016 Share Posted August 30, 2016 The springs are linear. Ebay has correct photo. Quote Link to comment Share on other sites More sharing options...
CarolinaTZ Posted August 30, 2016 Share Posted August 30, 2016 Great...thanks! Quote Link to comment Share on other sites More sharing options...
mnmleitch Posted October 18, 2016 Share Posted October 18, 2016 I purchased the full kit from brandcarpart for a 1975 280z and the rear struts were to short to install. The springs seem fine but will need to get back to you on how the struts go. I am hoping they send me the correct struts. The drop was perfect on my Z but I have the old struts in the back. Quote Link to comment Share on other sites More sharing options...
PseudoSport Posted October 28, 2016 Share Posted October 28, 2016 I purchased the full kit from brandcarpart for a 1975 280z and the rear struts were to short to install. The springs seem fine but will need to get back to you on how the struts go. I am hoping they send me the correct struts. The drop was perfect on my Z but I have the old struts in the back. Sounds like they sent you 240Z shocks for the rear. What part number did you get? Below should be the correct ones. #552205 240Z rears #552206 260-280Z rears Quote Link to comment Share on other sites More sharing options...
juxsa Posted November 7, 2016 Share Posted November 7, 2016 Did they ship you the correct rear Struts? I'm going through the same thing. I got them about 2 weeks ago and didn't have time until yesterday to mess with it but saw that the rears didn't fit. Looking at this thread it looks like they sent me the 240 rear Struts Quote Link to comment Share on other sites More sharing options...
NewZed Posted November 7, 2016 Share Posted November 7, 2016 You can just add a spacer (from a piece of pipe) to make up the distance on the rear strut. That's what Tokico does. Same strut on all four corners, two use a spacer. Seems like the distributor in this case just never got their database right and now they're screwed up forever. One of the downsides of the new technology age - mistakes tend to be permanent. There's a company out there advertising CV axles for 240Z's because somebody assumed and put it in to a database. Quote Link to comment Share on other sites More sharing options...
PseudoSport Posted December 2, 2016 Share Posted December 2, 2016 Did they ship you the correct rear Struts? I'm going through the same thing. I got them about 2 weeks ago and didn't have time until yesterday to mess with it but saw that the rears didn't fit. Looking at this thread it looks like they sent me the 240 rear Struts Yes, I eventually got a hold of the vendor and they shipped me the correct rear struts and let me keep the other ones. I had already installed the 240Z struts with a piece of pipe so i kept them in the car and did 3 races on those before swapping in the correct ones. Only reason I swapped in the correct ones is because I had the rear suspension apart anyway. Over all I'm happy with the setup and its held up well. Quote Link to comment Share on other sites More sharing options...
AdreView Posted August 8, 2017 Share Posted August 8, 2017 (edited) Going to bump "stop" this nearly a year later with my results having recently installed them on a 240Z. As one can see, the set is two different designed springs, not the similar looking ones used on the 280s. I installed the VA in the front and the HA in the rear (not entirely certain this is correctly labeled by whomever manufactured them) as specified by previous posts. On the ground the Z looks level and has even gap front/rear and rides very well, not jarring, not bumpy, smooth and quite comfortable. The measured drop from oem springs to these is approximately 1.6" in the front and .75" in the rear with the drivers side being 0.125" higher than the passenger side to accommodate drivers weight. The one area of concern is with the front coils being near coil binded throughout the entire length, which makes for only an inch or slightly more (not actually measured) of actual travel...I was wishing for more as I don't need to be this low. I understand its due to the design of a progressive spring including coil bind as a "helper" but why even design a spring to be this compressed with such a short travel? With the sheer lack of info on the manufacturing run of these through Vogtland and the added lack of info from any vendor which sold these I'm really wondering if the springs need to be swapped front to rear as similarly reported over the years with users of Eibach getting all confused as the F/R stampings changed from Eibach to MSA through their change-over. I haven't measured the actual spring rates of these other than accepting the data originally posted by JohnC (The 240z rates are 152 fronts and 170 rears), but I'm wondering how the balance and handling will be affected by the swap if done??? It's too bad there are such few options remaining for Z lowering springs on the market today. With most going the coilover route I can see why, but for those who don't want to go that route it's tough to find a well balanced solution. Vogtland Kit: Vogtland Front w/vehicle weight: Vogtland Rear w/vehicle weight: Another discontinued lowering spring option was Tokico, very similar results to above. Tokico Front w/vehilcle weight: Tokico Rear w/vehicle weight: Edited August 8, 2017 by AdreView Quote Link to comment Share on other sites More sharing options...
AdreView Posted August 8, 2017 Share Posted August 8, 2017 Just an update Had these for close to a year and a half now. Shocks still feel the same, car is still the same height as when i last posted in july last year. Feel nice on canyon roads and over bumps too. Interested in knowing if you installed them as VA in the front and the HA in the rear? Quote Link to comment Share on other sites More sharing options...
Milenko2121 Posted August 8, 2017 Share Posted August 8, 2017 Interested in knowing if you installed them as VA in the front and the HA in the rear? Yeah, that's how I installed them. Still working pretty well. Just tracked them in January and felt great. Tight course meant for gokarts. Quote Link to comment Share on other sites More sharing options...
AdreView Posted August 9, 2017 Share Posted August 9, 2017 Yeah, that's how I installed them. Still working pretty well. Just tracked them in January and felt great. Tight course meant for gokarts. Considering you have a 280, do you have the coil binding as I do in the front? Quote Link to comment Share on other sites More sharing options...
Milenko2121 Posted August 10, 2017 Share Posted August 10, 2017 Considering you have a 280, do you have the coil binding as I do in the front? I could not say, never visually tested the full travel of suspension. I haven't felt a bind myself. Quote Link to comment Share on other sites More sharing options...
AdreView Posted August 12, 2017 Share Posted August 12, 2017 I could not say, never visually tested the full travel of suspension. I haven't felt a bind myself. Just peek into the front wheel well with a flash light when you have a chance and report back if you can, I'm interested in knowing if it looks like the photos I posted above. Thanks Quote Link to comment Share on other sites More sharing options...
hatepotholez Posted February 12, 2018 Share Posted February 12, 2018 Any updates on this? I'm looking at the same kit. Thanks! Quote Link to comment Share on other sites More sharing options...
hatepotholez Posted March 5, 2018 Share Posted March 5, 2018 bump! Quote Link to comment Share on other sites More sharing options...
torynich Posted March 23, 2018 Share Posted March 23, 2018 So I tried ordering a set of shocks and springs for my early 260 off eBay today and my order ended up being cancelled and my money returned due to no stock. I tried contacting brandcarparts off their website also but never got a response. Is there any other affordable solution to springs and shocks without going coilovers? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.