Gen I & II Chevy V8 Tech Board

8917 topics in this forum

1. Engine Assembly Problem...HELP!!!

   By Guest butlersZ, May 28, 2004
   • 11 replies
   • 1.4k views
   • 
   • DaleMX
   • May 30, 2004

3. Chev V8 Tech

   By hanomon, May 29, 2004
   • 3 replies
   • 1.3k views
   • 
   • Dan Juday
   • May 30, 2004

4. SB engine plates or mounts for the z32

   By Guest NXRPERFORMANCE, May 26, 2004
   • 1 reply
   • 977 views
   • 
   • Guest
   • May 30, 2004

5. 280ZX starter question

   By Guest BillV, May 15, 2004
   • 11 replies
   • 1.9k views
   • 
   • 80LS1T
   • May 29, 2004

6. Engine/tranny alignment to differential side to side?

   By namz7791, May 28, 2004
   • 2 replies
   • 1.1k views
   • 
   • cyrus
   • May 28, 2004

7. Mount & Header really close to steering shaft

   By deMideon, May 27, 2004
   • 7 replies
   • 1.3k views
   • 
   • Tim240z
   • May 28, 2004

8. Posted Complete Conversion Set-Up In Classifieds

   By 240Z2NV, April 29, 2004
   • 11 replies
   • 1.9k views
   • 
   • 240Z2NV
   • May 27, 2004

9. Drive Shaft and Tranny Question

   By Toysport, May 26, 2004
   • 6 replies
   • 1k views
   • 
   • Toysport
   • May 26, 2004

10. Setback plate/spacer assembly order?

    By wheelman, May 26, 2004
    • 6 replies
    • 1.2k views
    • 
    • wheelman
    • May 26, 2004

11. I'm new to this page but I got problems

    By Guest tony78_280z, May 25, 2004
    • 2 replies
    • 813 views
    • 
    • labrat
    • May 26, 2004

12. Flywheel mystery question (Grumpyvette, etc.)

    By Heavy Z, May 26, 2004
    • 0 replies
    • 737 views
    • 
    • Heavy Z
    • May 26, 2004

13. Hybrid Z wins at local Z show!

    By Savage42, May 24, 2004
    • 4 replies
    • 1.3k views
    • 
    • Guest
    • May 25, 2004

14. Pulley sizes??

    By namz7791, May 25, 2004
    • 1 reply
    • 718 views
    • 
    • Guest
    • May 25, 2004

15. JTR engine not even...??

    By 72zcar, May 24, 2004
    • 15 replies
    • 2k views
    • 
    • 72zcar
    • May 25, 2004

16. requesting help and a bitch slap if necessary

    By Guest dancaprar, May 24, 2004
    • 5 replies
    • 1.1k views
    • 
    • deMideon
    • May 24, 2004

17. new pics

    By Graeme, May 21, 2004
    • 16 replies
    • 2.2k views
    • 
    • Graeme
    • May 24, 2004

18. I just got a 74 260z what swap is the best to put in?

    By Guest BlueDatsun350Z, May 23, 2004
    • 4 replies
    • 952 views
    • 
    • Guest
    • May 23, 2004

19. V8 BLock and parts posted in the forsale section...

    By Mikelly, May 23, 2004
    • 0 replies
    • 674 views
    • 
    • Mikelly
    • May 23, 2004

20. fuel pump for LT1

    By Guest shakav, May 20, 2004
    • 1 reply
    • 847 views
    • 
    • theBrit
    • May 23, 2004

21. 4/7 SWAP CAMS???

    By BillZ260, May 21, 2004
    • 1 reply
    • 862 views
    • 
    • jap tin
    • May 23, 2004

22. HELP VICTOR JR QUESTION...

    By Corzette, May 22, 2004
    • 2 replies
    • 900 views
    • 
    • Guest
    • May 22, 2004

23. Valve springs for Vortec heads?

    By labrat, May 20, 2004
    • 4 replies
    • 5.4k views
    • 
    • labrat
    • May 21, 2004

24. Backfire through freshly rebuilt carb

    By Guest E.Murray, May 18, 2004
    • 17 replies
    • 3k views
    • 
    • Guest
    • May 20, 2004

25. RX7 & Z31 compatability question

    By Guest Chevelle7d2, May 19, 2004
    • 1 reply
    • 1.2k views
    • 
    • Guest
    • May 20, 2004

26. setback plates

    By j260z, March 17, 2004
    • 14 replies
    • 2.2k views
    • 
    • Brad-ManQ45
    • May 20, 2004