Ja1991

So i'm in the process of building my z and when I took the head off I was an idiot and didn't check to make sure the bottom end was timed and now that i'm timing the car I ran across a problem. The head and cam sprocket both have marks so that is in the correct timing position but the bottom end has no markings. The sprocket for the crank has a punch hole but there is nothing on the block to line it up with so now i'm kind of stuck. Any help would be appreciated. Thanks guys

Awesome thank you!! I just need a Distributor now. Anyone have one for a decent price?

Still looking. This is the last thing i need for my swap guys. I would appreciate it if someone could help. Thanks

ttt

Still looking, if you have just the shaft let me know as well. thanks guys

I've found someone who will sell me a turbo distributor from an 82-83 turbo distributor now I just need the splined shaft. Anyone have one for sale? Thanks

bump

Man I thought they were a little cheaper than that. Let me see what else pops up and if nothing else then i'll see what I can do. Thanks for the speedy reply. ps. I'm not trying to be a cheap ass either, it's just my first turbo build and i'm a broke college student lol

Basically the title states it all, I need to buy a complete 82-83 turbo distributor for my megasquirt 2 install. Thanks guys/gals

Actually I don't know how to weld lol. I bought a mig welder, and i'm only 21 so one of my biggest problems is that I have to buy tools along the way. So i'm actually learning how to weld with some friends guidance. I am building MS2 for this project with a friends help, I also bought some rx7 550cc injectors, It came with 2 r200's, i'm not sure if the one on the car is an lsd or not so that may get welded. My power goals for this are 400whp, I'm going to sell my winter beater in about a month and try to get about $1300, that will go towards some Ground Control coilovers, ae86 short strut strokes, bump steer spacers, torsion rod, and a front strut bar. I'll be getting some work cr01's probably something like 15x9 15x10.5 and some carbon fiber ZG flares to fit them. As far as paint I haven't decided if i'm going to plasti dip it for now and save up to paint it or spend a few hundred dollars and set up my own paint booth and learn how to do that myself.

Hey guys my name is Joe Apostol. I'm pretty new to the Datsun scene. I live in Lansing, Michigan and in November of 2012 I purchased my first Datsun. I bought a 260z that came from North Carolina and looked like it had sat in the woods for a few years. I picked it up for $2300 with 80k miles, an l28 and 5 speed swap, rear disc brake conversion and it also came with a new exhaust and all new suspension/bushing throughout. I drove it for the first day I owned it and then put it in the garage and started working on it. Updates will be every couple weeks as I work a lot and am a full time student. So here are the pictures. I look forward to your comments and any advice you may have. Thanks The day it arrived at my house. I bought it and had it shipped to me Gutted it later that week Took out the center console and tried to fix some of the cracks so it wouldn't fall apart. I plan on buying a new one eventually Started installing carpet ripped off the exhaust cut a piece of the floor out and welded in a new patch bought a non webbed non egr manifold. Going to port it for the 60mm tb I bought Cut a hole in the turbo manifold so I can weld in my wg Installed the new cylinger head, been resurfaced, 5 angle valve job, also installed a cometic mls headgaske and arp head studs The worst of the rust, I cut most of it away since the picture and i'm going to fiberglass over it Brand new Greddy td06h 20g 76. trim Wastegate and dump tube. still have to weld it to the manifold I think that's about it for now.

Found one. Thanks guys

Looking for a non-webbed non-egr intake manifold in good shape. Thanks

converting my 260z into an l28et and i'm looking for a nice 3in downpipe. Let me know what you have. Thanks -Joe

Basically what the title states. I'm looking for an holset hy35, the waste gate can be welded shut. I'm also looking for a 60mm 240sx throttle body, I suppose any compatible 60mm TB will work. I'll be adding stuff to the list as well. I'm just trying to get my turbo swap done. Thanks Guys -Joe