GrenadeZ Posted July 24, 2009 Share Posted July 24, 2009 does anyone know if this swap would be similar for the 7m? i can get one....FOR FREE!!!! the whole car is a in a junk yard I have been helping out at and part time racing for. Quote Link to comment Share on other sites More sharing options...
Gritz Posted July 25, 2009 Share Posted July 25, 2009 does anyone know if this swap would be similar for the 7m? i can get one....FOR FREE!!!! the whole car is a in a junk yard I have been helping out at and part time racing for. Do it!!! Most swaps are the same..mount it, wire it, tune it, prepare the car for it, kick butt with it!!!! Quote Link to comment Share on other sites More sharing options...
GrenadeZ Posted July 25, 2009 Share Posted July 25, 2009 Im going to check it out next week. Its missing a title and is an old repo. Hopefullly the HG is in good shape. Quote Link to comment Share on other sites More sharing options...
Gritz Posted July 25, 2009 Share Posted July 25, 2009 Im going to check it out next week. Its missing a title and is an old repo. Hopefullly the HG is in good shape. Nope..bad move...If you are going to use the 7m..be sure to at least deck the head, use metal head gasket and arp head studs...then boost 20psi all day long!!! unless, all that has been done already... Quote Link to comment Share on other sites More sharing options...
RUSSJZ-ZED Posted September 18, 2009 Author Share Posted September 18, 2009 Adios time, Zed free, gone, no more. Waved it goodbye the same day ZOOM magazine(#138) came out with a feature on it.Damn! another week would have got more for it. Great article, the previous owner of the car was so impressed that he emailed to express his disgust at the way I had "destroyed":icon6: a "good" Zed. Might do it again to another one some day. New project is annoying Porsche true believers. 2002 4.3 Vvti Levus 3UZ V8 into a 928S , I was going to use a 2JGTE, but they weigh in 200 pounds heavier than the NA V8, (same power figures though) Undecided as to if it is going to be a Toysche or a Plexus. Have fun "mutilating" Z's, Bye. Quote Link to comment Share on other sites More sharing options...
XTCoX Posted December 26, 2009 Share Posted December 26, 2009 You, my friend, deserve a medal for taking the time to write this. Thanks a million. Quote Link to comment Share on other sites More sharing options...
timbo1jz Posted December 27, 2009 Share Posted December 27, 2009 you got rid of the z? That makes me sad . You were an inspiration to my build man and gave me so much good info! Thanks for your help, and at least your building another bad ass project! Quote Link to comment Share on other sites More sharing options...
camarojokester Posted January 20, 2010 Share Posted January 20, 2010 i wonder if it would be easier to use the factory motor mounts and add some plates on the frame for it to bolt on to Quote Link to comment Share on other sites More sharing options...
proh22a Posted February 13, 2010 Share Posted February 13, 2010 good jop very nice Quote Link to comment Share on other sites More sharing options...
Sinjin Posted April 9, 2010 Share Posted April 9, 2010 thanks a lot. i just got my 240z shipped in yesterday and i my roommate just received a 2JZ on trade for labor...this could get interesting. now i just need to figure out what i'll use for a diff. Quote Link to comment Share on other sites More sharing options...
richracing Posted May 30, 2010 Share Posted May 30, 2010 ill be using a z32TT viscous lsd diff. i was wondering wich driveshaft that you used? or is it custom? Quote Link to comment Share on other sites More sharing options...
jDM-S30 Posted July 17, 2010 Share Posted July 17, 2010 If you don't mind me asking, How much did you pay for the 1J & what was your budget like to do the whole swap? Looking at different swaps. I would much appreciate the response to make my decision. Thank you. Quote Link to comment Share on other sites More sharing options...
haggered_z Posted December 30, 2011 Share Posted December 30, 2011 ok so i have an 81 zx has anyone tried this concept with the type of car i have, or would i need to completely pull something out of my ass for it to work? Quote Link to comment Share on other sites More sharing options...
pat1 Posted December 30, 2011 Share Posted December 30, 2011 ok so i have an 81 zx has anyone tried this concept with the type of car i have, or would i need to completely pull something out of my ass for it to work? You would have to get a custom oil pan built. The mid sump on the 1jz/2jz will hit the subframe. Quote Link to comment Share on other sites More sharing options...
haggered_z Posted December 31, 2011 Share Posted December 31, 2011 You would have to get a custom oil pan built. The mid sump on the 1jz/2jz will hit the subframe. i was going to get a rear sump out of a na 2jz Quote Link to comment Share on other sites More sharing options...
williamb82 Posted April 3, 2012 Share Posted April 3, 2012 (edited) heres a post i made on celicasupra.com on how easy it is to get a 2jz aristo swap running. id post the link but not sure its allowed, so here is the key posts i made. hope it helps you guys with the wiring. these are specific to wiring it into a mk2 supra, however i listed what the wires on the 2jz harness are for, so hopefully it makes it easy for you guys. post from 7/30/11 4 wires on the small ecu plug to +12v, and 1 pin on the body plug to +12v, then the gnd to the block, the power to the starter. power the fuel pump, and 1 more wire on the body plug triggers the starter. just fired my 2jzgte up today to make sure it doesnt smoke or knock. bought it yeterday. runs great as is other then a couple small vac leaks from vac lines. heres a vid. ill draw up a diagram in paint later and post it for you guys. instructions below i made these 2 pics big on purpose guys, i hope they help. large mk2 ecu connector behind the glovebox ok, e10 is the only connector here you need to look at. the other 2 are the engine harness. pin 1 is a black wire with orange stripe. it needs to be connected to ignition switched power. it goes to IG S/W on the stock mk2 ecu plug pin 31 and 32 are both black with a red stripe. they need to be connected to the main relay. they receive power when the ecu switches the main relay on. the go to B+ on the large mk2 ecu connecter behind the fuse box (+12v switch. higher current so id put it on a 30 amp relay) pin 33 is white with a red stripe. it gets constant 12v from the battery. this goes to BATT on the stock mk2 ecu connecter pin 24 is green with an orange stripe which is the wire that triggers the main relay to turn on. this goes to M-REL on the stock mk2 ecu connecter (this needs to +12v that is ON while cranking. it would trigger the relay mentioned that supplies the B+ voltage) pin 4 is green with a white stripe. it goes to the stop light switch. i believe this goes to the non powered side so that it receives power when you hit the brakes. only worry about this if on the stock ecu. it will likely tell the ecu when to cut the fuel off for deceleration which should improve gas mileage and driveability. pin 16 is red with a yellow stripe. it is the tach signal. it will require a tach adapter like the msd 8920 to work the mk2 stock tach(or stock z tach as it is also analog). or do the resistor changes needed on the stock tach. there is a thread floating around here somewhere on that. pin 28 is black with a red stripe and is the main overdrive switch. im guessing this needs to be switched to ground to have overdrive on. i recommend checking this wire while the ecu is switched on before connecting it to anything. if it has voltage to it then yes, it needs grounded to engage overdrive.(this is if you plan to stay with the auto trans) pin 34 is black with silver dots on it. this is the ac amplifier. i believe this hooks to the stock ac amplifier circuit so that when you turn your ac on it will engage the ac compressor through the stock engine harness plug and increase the idle. the ac amplifier iirc will turn the ac off if the pressures are too high or too low pin 23 is white with silver dots is the ac magnetic clutch relay wire. this should be what actually triggers the relay to engage the clutch of the compressor. not sure if this is the one that connects to A/C on the mk2 ecu plug or not. pin 3 is green with a yellow stripe and is the kick down switch. im guessing the jdm aristo had a gas pedal mounted switch to make the auto trans kick down when you floor it since there is no kick down cable. if your going manual it isnt needed obviously, but if you stay auto, youll need to install a micro switch on the gas pedal or on the throttle linkage under the hood. then again it may drive fine without it. up to you. pin 6 is black with a yellow stripe and is for the check engine light. it goes to "W" on the large mk2 ecu connecter.(id recomend connecting this to your engine light if you have one, if not, mount an led somewhere for it so you can check engine codes when needed. it will help troubleshooting issues tremendously!) Edited April 3, 2012 by williamb82 Quote Link to comment Share on other sites More sharing options...
williamb82 Posted April 3, 2012 Share Posted April 3, 2012 (edited) this is the body plug on the aristo engine harness. hopefully you got an engine with the plug uncut like mine. i cant list wire colors until i can cut a body harness plug out of an aristo at the junkyard. hopefully i can even find one. they dont pop up often. pin f1 is the starter trigger. this goes to the wire you use to the mk2 trigger wire so that when you turn the key it will start the car.(in your case, the z starter trigger) pin f6 needs to go to the main relay power. since it powers the injectors and coils etc.., might want to use the main relay (+B on the large mk2 ecu connecter)to trigger a separate 30 amp relay that is powered from the battery with its own fuse. (id use the same relay as the B+ wires at the ecu plug. thats why i recomended a 30 amp relay) pin f8 is the oil pressure signal wire. if its like most other toyotas, it is the same range as the stock sending unit so should work the stock oil pressure gauge just fine. this goes to OIL on the mk2 ecu plug(if using your stock oil pressure gauge, use your stock z sender. the toyota port is 1/8in bpt as i recall. they sell 1/8th bpt to 1/8th npt adapters in case the nissan is npt thread) pin f9 is the engine temp gauge wire. again, it should control the stock gauge just fine. (its not listed on the above pic, but should be a yellow wire with green stripe on one of the unlabeled pins of that pic.(if using the stock datsun gauge, use the stock datsun sender) pins f7 and f11 are listed as grounds. i know they arnt needed for the engine to run. they may be to ground other items that go through this connector, but it wont hurt to ground these wires to the body.(as it turns out, they just ground stuff from inside the car. you dont have to hook these up at all) pin c5 says ac_mg. i believe this is the wire from the ac clutch relay that goes to the actual clutch. you could just run a wire through the fender well from the stock mk2 wire into the cabin behind the dash to this, though there might be an easier way, i havent looked into it. pin d1 is for the oil level sensor. the mk2 doesnt have a light for this, but i highly recommend hooking up an led somewhere with 12v power through the proper resistor and the gnd leg connected to this wire. id put it in the gauge cluster if it were me, and make it bright as possible. this will notify you if your oil level drops too low.(id rig an led waring light for this to let you know if your oil level is low.) this info is free so you do not owe me anything, but donations are welcome! Edited April 3, 2012 by williamb82 Quote Link to comment Share on other sites More sharing options...
sqweekykneecap Posted July 2, 2012 Share Posted July 2, 2012 This is one of the best threads ive read. I love every bit of information/link/pictures that is given from all parties! reguardless of the money i have in my heavily rebuilt L28et with a z32 trans in my 260z, the the JZ engines sure have sparked my interest recently! thanks for an awesome thread!!! Quote Link to comment Share on other sites More sharing options...
KTMStrawn Posted December 21, 2014 Share Posted December 21, 2014 Sorry if this is a silly question but i feel like it wasn't expliciyly explained in the wiring advice above. So as far as the EFI relay goes for our Z's, we basically just get a 30 amp relay and wire pin 24 to trigger the relay and wire pins 31,32, and f6 to be powered by the relay correct? Quote Link to comment Share on other sites More sharing options...
RUSSJZ-ZED Posted July 9, 2016 Author Share Posted July 9, 2016 (edited) Not a Z but it ended up looking like this. Sushi porker. It has Datsun Z content, the cross engine brace started life as a 260Z front swaybar. Tunnel rebuilt to take the 5 speed auto (at the front) transaxle gone replaced with 3.08 Borg Warner LSD -Weisack rear suspension retained, Porsche Cayenne rotors front, Porsche 968 (front) brakes fitted on the back. Mk4 Supra Master cylinder and servo, Alloy radiator. 1380 Kg 3036lb (53% front, 47% rear) It really upsets Porsche people, Lighter, faster, reliable, corners like a rat, plus- more economical, 12000 kilometers so far, and the only outlay has been for fuel. Edited August 16, 2016 by RUSSJZ-ZED Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.