Gen I & II Chevy V8 Tech Board

8917 topics in this forum

1. Add Power Steering In A 260Z ?

   By Guest Anonymous, June 24, 2002
   • 1 reply
   • 1.1k views
   • 
   • Dave
   • June 25, 2002

3. ADDING A PICTURE OF MY CAR

   By Guest Anonymous, March 27, 2002
   • 10 replies
   • 2.3k views
   • 
   • Guest
   • March 29, 2002

4. adding lifter bore grouves

   By grumpyvette, September 29, 2002
   • 0 replies
   • 997 views
   • 
   • grumpyvette
   • September 29, 2002

5. adjusting valves with less mess!

   By grumpyvette, June 7, 2003
   • 2 replies
   • 1k views
   • 
   • Graeme
   • June 10, 2003

6. Adjustment of Hydraulic Throwout Bearing

   By Guest TBroZ, March 11, 2003
   • 7 replies
   • 2.6k views
   • 
   • pparaska
   • March 11, 2003

7. Adult perspective on the 300ZX or HybridZ...

   By Guest Pegasus76, September 15, 2003
   • 12 replies
   • 2k views
   • 
   • Guest
   • September 19, 2003

8. Advanced Cast Iron Machining Q's

   By tfreer85, March 22, 2006
   • 19 replies
   • 3k views
   • 
   • jap tin
   • March 25, 2006

9. Advantages of a large bore?

   By Guest TestZubject, March 19, 2004
   • 5 replies
   • 1.2k views
   • 
   • Guest
   • March 20, 2004

10. Adverse Effects Of Copper Head Gasket for Street Use?

    By Guest SBZ, April 26, 2004
    • 2 replies
    • 1k views
    • 
    • Pyro
    • April 26, 2004

11. ADVICE NEEDED - '72 240Z

    By Guest Anonymous, October 12, 2001
    • 7 replies
    • 1.9k views
    • 
    • BLKMGK
    • October 13, 2001

12. Advice on engine build

    By mr_han_solo, August 20, 2013
    • 16 replies
    • 3.8k views
    • 
    • Robftw
    • September 7, 2013

13. Advice on heads needed

    By BayAreaZT, June 4, 2002
    • 8 replies
    • 1.8k views
    • 
    • Guest
    • June 5, 2002

14. Advice on to rebuild or not to rebuild

    By Herman, September 20, 2012
    • 6 replies
    • 509 views
    • 
    • daddydonuts
    • September 20, 2012

15. Advice on Transmission install

    By marinez, June 1, 2016
    • 3 replies
    • 1.9k views
    • 
    • marinez
    • June 1, 2016

16. Advise from engine builders, I keep blowing intake seals?

    By fastzcars, July 7, 2008
    • 8 replies
    • 5.4k views
    • 
    • Turbo Meister
    • July 9, 2008

17. advise needed on 260z 2+2 with 350

    By ZROSSA, September 10, 2001
    • 0 replies
    • 1.2k views
    • 
    • ZROSSA
    • September 10, 2001

18. Advise on TT V8 setup 1 2

    By Tim240z, August 3, 2001
    • 33 replies
    • 4.8k views
    • 
    • Tim240z
    • August 10, 2001

19. Aerodynamic aids and 1/4 mile time improvements? 1 2

    By Guest norm[T12SDSUD], February 6, 2004
    • 25 replies
    • 8.5k views
    • 
    • A. G. Olphart
    • October 21, 2006

20. aeromotiveinc phantom fuel system install

    By theBrit, August 23, 2014
    • 6 replies
    • 4.3k views
    • 
    • Tank
    • June 16, 2020

21. AFR 220 vs. stock Vortec?!?!?!!?!?

    By Mike C, February 1, 2003
    • 4 replies
    • 1.8k views
    • 
    • Mudge
    • February 2, 2003

22. AFR angle plug heads and block hugger header clearance?

    By pparaska, February 27, 2003
    • 19 replies
    • 10.5k views
    • 
    • pparaska
    • March 4, 2003

23. afr eliminators

    By dustin280zx, September 18, 2006
    • 1 reply
    • 879 views
    • 
    • grumpyvette
    • September 18, 2006

24. AFR vs. Edelbrock rpm heads

    By Guest zfan, August 17, 2003
    • 1 reply
    • 1k views
    • 
    • Corzette
    • August 18, 2003

25. After a long break, I'm back

    By Zoso240z, June 14, 2008
    • 1 reply
    • 859 views
    • 
    • Jerminator96
    • June 14, 2008

26. After driving a 911 and RX7 back to back today, all day. i dunno which one to build!! 1 2 3

    By Guest ON3GO, October 5, 2005
    • 46 replies
    • 14.8k views
    • 
    • MazterDizazter
    • February 2, 2008