Apex Engineered Track Attack Spring/Shock Discussion

[baby_Carlton]

Hi HybridZ, its been a while. Took a long sabbatical from working on my S30 to finish college and get a job. For the last 6 or so months its been full steam ahead, the project is currently being rust repaired at a local body shop and I've been collecting parts as budget allows.

 

The first piece major piece of hardware to arrived is the Viking Performance Shocks from the Apex Engineered Track Attack Front/Rear Suspension kit. I noticed that Apex’s website lacks details on shock and spring selection, so I’m documenting my findings here for others and to start a discussion on their choices.

 

What's Included:

Box as it arrives from Viking Performance

 

Serial Numbers of each of the shocks (PN: C203)

 

Viking Performance Shocks Link

 

Part Numbers of Springs (600# & 700#)

 

Initial Impressions:

The car will be caged and used primarily/almost exclusively on track, so a stiffer setup is expected. However the spring rate selection still raises some concerns:

• The S30 chassis doesn’t benefit significantly from extremely high spring rates, even with a roll cage.

• The rear suspension uses inboard cantilevered shocks, which traditionally increase effective spring rate via the lever arm.

• This spring selection guide from Viking Performance indicates that the spring rate for a car with IRS and axle weights of ~1200-1400# is a lot lower than the supplied springs.

 

I'm hypothesizing that the high rates were chosen to prevent the shocks, which are short to fit the Z’s narrow frame and tight packaging within the front wheel wells, from bottoming out.

 

I’ve reached out to Apex Engineered to clarify the wheel rates for this setup and will update this thread when I hear back. Let me know if any of you have run this kit or high wheel rates.

 

 

Edited Monday at 06:42 PM by baby_Carlton
Inclusion of spring selection guide from Viking Performance

[jhm]

Welcome back, Carlton...and congrats on the major life changes/accomplishments! 

 

Following, as I'm super interested to hear how about the installation and how you like it.  Thanks for documenting the process!  👍

[Ben280]

Good post. I was frustrated for a long time with companies not sharing spring rates on these parts. FWIW, Viking is legit, lots of fast SCCA guys run those things with good results. 

 

IF those spring rates were chosen to prevent bottoming out of the shocks, that's pretty poor design. My guess is that the motion ratio of the bellcrank will be the limiting/bottoming out feature here, and that the conversion to pushrods has resulted in some high force multipliers. My guess would be Viking starting point is mounting in a "muscle car" front end, where the motion ratio is fairly low. 

 

I'll be interested to hear what the APEX guys say!

[baby_Carlton]

On 7/7/2025 at 7:16 AM, jhm said:

Welcome back, Carlton...and congrats on the major life changes/accomplishments! 

 

Following, as I'm super interested to hear how about the installation and how you like it.  Thanks for documenting the process!  👍

Thanks for the welcome back, this car has certainly had a rollercoaster of a fate over the last 10 or so years of ownership. Excited to build it into the best version of itself (for me).

 

On 7/7/2025 at 2:15 PM, Ben280 said:

Good post. I was frustrated for a long time with companies not sharing spring rates on these parts. FWIW, Viking is legit, lots of fast SCCA guys run those things with good results. 

Thanks for the info, seems like Viking is a non-hype brand that offers shocks that do shock things, which I can appreciate. AE is slow on CS communications but that's understandable given the size of their operation. That said, for a ~$9K suspension kit, a bit more transparency and technical detail on their website would go a long way. If I can find a shock with more travel for the same dimensions or when I blow these out I'll swap. JRi's builder series and some of their GM line looks like it would bolt right in, only 0.3" longer extended length which seems negligible in terms of fitment (PN: 100-511-300). 

 

On 7/7/2025 at 2:15 PM, Ben280 said:

IF those spring rates were chosen to prevent bottoming out of the shocks, that's pretty poor design. My guess is that the motion ratio of the bellcrank will be the limiting/bottoming out feature here, and that the conversion to pushrods has resulted in some high force multipliers. My guess would be Viking starting point is mounting in a "muscle car" front end, where the motion ratio is fairly low. 

I agree, it seems incredibly unwise if that were the case but it wouldn't be the first time I'd seen it. I've seen similar suspension choices in GTAC (cars riding on bump stops) but that's usually done purposefully to keep the aero platform working optimally and not appropriate for a package like this. Considering the shock travel is a mere 3.6", its safe to assume this is an extremely low motion ratio design. It feels like a missed opportunity to fully leverage the bell crank inboard design (traditionally speaking) but perhaps packaging constraints of the S30 chassis left little room for alternatives.

 

I'm hoping the bottoming out feature will be at the upper A-arm which would allow me to mount a 3D printed polyurethane bump stop on top of it.  Going to email AE for an update on the wheel rates and now information motion ratios, thanks for the idea.

Edited 1 hour ago by baby_Carlton
Grammar