-
Posts
232 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Events
Gallery
Downloads
Store
Everything posted by spacecase70
-
instructions to bolt on the mount, that is pretty straight forward, you just use 2 short bolts on the set back plate, and three long ones to go thru the plate and spacers but remember to trim about a 1/2 inch from the bottom rear corner of the driver side mount
-
diference in stock strut length
spacecase70 posted a topic in Brakes, Wheels, Suspension and Chassis
ok i have ben serching for an answer to a question, what is the difference in length between a 240 and 280 strut length, I have had no luck in finding the answer after serching for two hours! please help me in this i need to know which strut is LONGER! I have a set of new 240 rear cartridges, and want to put them into my 280 rear tubes, will they fit? or are they too long? please guys and gals! -
Oil Pressure Switch per JTR
spacecase70 replied to Georgia Flash's topic in Gen I & II Chevy V8 Tech Board
It's too late now, but, they also sell the oil pressure guage T-adapters at Autozone in their "performance" section. lol i could have told you that but i havent been on in a while, thats where i find all the parts i am looking for -
omfg!!!! i can only hope my project comes out looking half to a quarter as good
-
Ok Grumpy, I took your advice and bought the JTR book! so next question, I am planning on using a 5.0 and th700R4 from a 1989 Camaro and using the stock everything, just one problem.. I dont hae the wire harness or computer from the doner vehicle because it burned up in a garage fire, engine compartmint was untouched and i was thinking of using the bosche unit for a z in the TBI is it possible to use this or should i look in a JY to fine the proper pars?
-
thanks for the replys, problem has been resolved thred is closed
-
I am looking for a zx dizzy not a crank angle sensor dizzy I need the one with the six points in it, please
-
UHH...... WOW!! I love your diagrams, so simple and easy for me to follow! keep up the good work
-
ok i am sorry to hijack the thred too... I nstalled a hei modual in my 76 280z because of ignitiong failure when warm. I hooked it up as in these pictures and guess what... no start! when I jumped the red and green wires from the dizzy to the stock modual wiring it started and stayed running when I removed the jump wires. I drove it home ten miles ran great! had awsome power but after i shut it down, tried to restart and had the same problem??? i am at a loss could I get a little help on this too! please i am confused too here is te link to a video
-
well i guess the L24 injectors from a L24E maxima engine would do the trick
-
72 240z right side under dash relays needed (this week!)
spacecase70 replied to aziza z's topic in Parts Wanted
you could always change the plugs on the switch to fit, just a thought -
Rota RB/RB-R, 4x114.3, 17", Z-Offset Wheels
spacecase70 replied to rudypoochris's topic in Group Buys
I recieved my wheels today and had the tires mounted, 245/40 zr17 front, 275/40 zr17 rear! they look AWSOME cant wait to put my flares on and take a few pics! Thanks for getting this GB started I am sooooooo Stoked! -
Fairlday z Fender mirror Installation on '71 240
spacecase70 replied to papastoy's topic in Body Kits & Paint
Now would have to reverse the measurements from the RH to the Left? I also noticed that the measurements are different for each side......why is that. that is because of the seating position of the vehicle, so just reverse the measurements for the LHD car and it will be correct for your car. I am sorry i dont know the link off hand, but if you had found them before then you should not have a problem with the relativly simple install -
Grumpy would have a copy of JTR manual on one of your hard drives that you could e-mail to me? maybe even the dimentions of the set back brackets and the thickness of the spacers? i really want to do the swap, I am usin an 89 camaro rs for the donor. is has no mods that i can identify, and has a th700r4, like the fact of the overdrive! I will be using an r200 with 3.54 gears, and 280z components from a 76 on a 74. any help you could provide me would be greatly appreciated! just dont have the resources to get the book, but have the machine tools to make the parts! anywho I really could use your valuable information on this build!
-
hey guys, I am looking for a used JTR book so that i can perform the swap in my 74 260z someone please have it for sale, donations greatly appreciated!
-
ka24de into 240z swap completed with turbo
spacecase70 replied to subtle_driver's topic in Nissan 4 Cyl Forum
pm sent -
man thats clean!
-
and the intake has a C wraped around the T and a styled "E" using part of the T cast into it! so its a CTE manifold looks like an MSA intake but its not, much older.
-
in reguards to the oil filter you saw on the block, i put it on fr cleaning the block. we have all the parts including to dual oilfilter setup with oil cooler too! we had noticed when we were cleaning the oil pump, it had the initials D. M. stamped into it, and there is alot of welding on the pump for the fittings used. we were hoping someone could identify the initials to find out who built the pump. thenk you for the part numbers though! that is a big help for replacing the part if ever needed!
-
any thoughts on the 82 maxima trans. I would like to know the ratios on it since i put one in my 74 ?
-
fantastic progress man, I hope to be able to do something like that with mine! but money does not exist for me anymore
-
Intake Manifold Porting and Injector upgrade
spacecase70 replied to softopz's topic in Nissan L6 Forum
BRAAP is the man when it comes down to building power from the L- series engines, his advice is that of a sage! follow him and youwill be on the right track! -
also try taking out your injectors and clean them, may have a obstruction in the nozzle that will not let the injectors close from the time it sat. don't forget to clean all the connections on the FI system
-
Hey guys, we are finally getting to work on the FoxZM hot rod Z! It is a 1970 240Z with 43,000 original miles, and was highly modified for playing on the track. We are posting pics for the build and posting answers to any questions reguarding the pics, and asking for advice( attn. BRAAP) concerning this endeavor. So please enjoy the pics we will be posting more to come!