Jump to content
HybridZ

BRAD D

Members
 View Profile  See their activity

  • Posts

    726

  • Joined

  • Last visited

 Content Type 

Everything posted by BRAD D

  1. BRAD D
    Hey Mikey, It's Brad's G/f again, here's some advice... Why don't ya put an RB26 in your 280, i hear that get's all the ladies! And as for the color, vomit green is really pretty... ah, maybe that is the problem.
  2. BRAD D
    There are more than just one page of photos, the other pages have better photos.
  3. BRAD D
    Sorry she wanted to put in a post
  4. BRAD D
    HI... this is Brad's girlfriend! I would prefer if all of you boys with your silly little Z cars would stop ragging on my pretty civic!!!! Why don't you all get off your computers and spend some time with your girlfriends/ wives! I am sure they have all heard enough about Z cars to last them a life time... It was nice to meet you guys!
  5. BRAD D
    A couple of turbos will quiet that right up Ross I got my CV adapters, Look nice thanks
  6. BRAD D
    That is too bad....but the Intercooler still looks good....
  7. BRAD D
    not an SR20 but you get the idea [/img]
  8. BRAD D
    How about making motor plates off the front of the motor, It would line up with the crossmember.
  9. BRAD D
    So would you hit the brakes every time you shift?
  10. BRAD D
    Ok,Ok I dont have a Z I just photoshoped Stony's car green
  11. BRAD D
    It is hard to get the press on the rear A-arm I had to use an air hammer And all you need to do is start the old busshing on fire and they will burn out, so you might not need a torch
  12. BRAD D
    And you might want to sand blast and POR15 the parts after too So add a sand blaster to that list 8)
  13. BRAD D
    Well you need a torch to cook out the some old cast in rubber bushings. Then you need an air hammer to hammer out some of the old bushing shells. And you dont need a press (less chance of trashing your parts) but it helps get out front arm shells. If you find a way to get the rear arms in a press let me know
  14. BRAD D
    Installing an RB26DETT Other that that the bushing kits are a PITA, What else takes a torch, air hammer, and a press??
  15. BRAD D
    Oh...I see now
  16. BRAD D
    Ok, I know the RB26 can have cooling problems but that rad is huge. Full of water that thing must mess up the 50/50 right? But that is a nice setup anyway
  17. BRAD D

    SDS Timing Wierdness!!

    BRAD D replied to Nigel's topic in SDS

    I have heard that RX7's run so hot that they fry injectors, so be careful if you buy used ones
  18. BRAD D
    ON3GO, the Celica seats would look nice with your blue paint. And I dont think any after market seat will have as good of a fit & finish as a toyota seat.
  19. BRAD D
    That should work but Griffin is cheaper I think.
  20. BRAD D
    And the GTR has one more gear, its a 6 speed right?
  21. BRAD D
    One of these I think http://griffinrad.com/winstoncup.htm
  22. BRAD D
    http://www.summitracing.com it is for a chevy, it was a long time ago that i got it. So i forget the part # or how much it was. But it was hooked up to my L24 before I did the RB swap so it will work for your L28et. But I think there is two kinds one that the lower tube bends in and is too close to your altenator, and one that dose not bend in that you want. 24"x19" rings a bell but ask others first.
  23. BRAD D
    I use a 16" permacool fan and a griffen rad here is a photo.
  24. BRAD D
    I have Hellas and I like them, but it is time for the relay mod for me too
  25. BRAD D
    Intercooler, Nice Rad, SDS or some other ECU. Get this bad boy up and running 8)
×
×
  • Create New...