Jump to content


Photo
- - - - -

1978 280z 3.1L Turbo LDS Parting Out


  • Please log in to reply
54 replies to this topic

#1 Kash

Kash
  • LocationRound Lake Beach, IL

Posted 21 November 2016 - 10:41 AM

Unfortunately I am parting out my car due to 2 dead beat winning bidders on eBay.  
The car ran and drove great with no issues whatsoever. It was a blast to drive with plenty of power and a wonderful exhaust note… fairly new radiator, starter, alternator, brake and clutch master cylinders, clutch slave cylinder and NGK plugs.  Just got done breaking it down and ready to ship parts out immediately/ local pick up upon receipt of payment (will still take $4000 for all).

The car is complete with all upgraded parts installed within the last 10,000 miles and engine rebuilt in the last 5,000 miles. I have all parts for sale, PM if you need something I did not list with a reasonable offer and it is yours:

Here are some of the key upgrades for sale (will post pic soon or PM):

Engine:
L3.1 Stroker Engine (N42 Long-Block) bored to 3.1L w/ LD crank and 240Z 9mm rods(ARP Studs and nuts) - $1300

Turbonetics t3/t04E Turbo with Stage 3 Exhaust Wheel/ .60 compressor wheel - $300

JWT 420 tuned ECU & Cobra MAF (includes wiring harness w/ coil and all sensors needed) - $400

MB 420 Injectors w/Pallnet fuel rail and Walbro pump - $300

N42 intake w/240SX 60mm TB - $100

2.5 to 3” mandrel bent downpipe - $75

3-Inch Exhaust w/ Magnaflow Muffler - $75

FMI 12x24x3 w/ custom piping - $100

Aftermarket Oil Cooler w/ adapter and hoses - $50

Electric Fan with shroud - $50

 

Drivetrain:

Z32 5 speed Trans w/ Austin Yoke adapter and custom drive shaft - $750

z31 r200 LSD with rear mounting bracket - $850

Spec II Clutch w/ Fidanza Flywheel - $250

z31 CV's - $150

Modern Motorworks billet adapters - $250

Rear Spindles Stub Axels - $75

Front Disc Brake System (Toyota 4 piston mono-block 4 piston calipers, cross drilled rotos and braided lines) - $175

Rear Disc Brake System (brackets w/cross drilled rotos and braided lines) - $175

Hydraulic Power Steering System w/Subaru rack and Toyota ends (operates flawlessly) - $400

 

Suspension: Urethane Bushings all around

Motorsport Sway bars - $200

Front and rear high strength Stress Tower Bars - $150

Tokico illumine 5 way Adjustable Shocks w/Eibach Springs - $350
Wheels/Tires:
15x8 Rota RB rims  (great condition) - $250

Interior:

Mazda Miata Leather Seats (fully adjustable on OEM tracks – looks great) - $250

Other OEM parts:

Stock turbo exhaust manifolds - $50

Emergency brake linkages and cables - $50

Fairly new Radiator form AutoZone - $50

All gages (clock replaced with matching boost) - $100

Black Interior panels and leather raps - $100

Center console w/ padded aftermarket harm rest- $50

Black Door panels - $150

? - $?


[SIGPIC][/SIGPIC]
'78 280z 3.1 Stroker, t3/t04E w/JWT Z31 ECU & Cobra MAF, Z32 5 sp, z31 r200 LSD w/CV's, Fidanza Flywheel, 4 Wheel Disc and Power Steering

3.1 Turbo Stroke Build-Up


#2 ritrebor

ritrebor
  • LocationLos Angeles, CA

Posted 21 November 2016 - 10:50 AM

PM sent for Companion Flange Adaptors & Stub Axles

 

ritrebor


Edited by ritrebor, 21 November 2016 - 03:35 PM.


#3 DespicableZ

DespicableZ
  • LocationTucson, AZ

Posted 21 November 2016 - 11:16 AM

I'm interested in the stress bars and front sway bar.

#4 Neverdone

Neverdone
  • LocationMilwaukie, OR

Posted 21 November 2016 - 11:40 AM

have any pictures of the interior and door panels?


Edited by Neverdone, 21 November 2016 - 11:40 AM.


#5 SRRTz

SRRTz
  • LocationNederland, TX

Posted 21 November 2016 - 11:56 AM

How about the center console? Is it crack free or at least nearly crack free?


1977 280z Turbo: N42/P90a - both rebuilt to stock specs, t3/t04B hybrid turbo, shaved early EGR intake, TiAL BOV and wastegate, Mishimoto intercooler, 2.5" mandrel bent downpipe to 3" mandrel bent exhaust, currently running 10psi boost. Fuel and wasted spark ignition controlled by a MS1 v3.0 board. Power goes to the ground through an 83 NA 280zx trans, stock 3.54 R200 (LSD coming soon) and turbo snowflakes wrapped in 205/55 R15 Dunlop tires. 


#6 malibud

malibud
  • LocationNEAR: Black Mountain, North Carolina

Posted 21 November 2016 - 12:03 PM

interested in the long block pm sent 



#7 grillhands

grillhands
  • Locationedison nj

Posted 21 November 2016 - 12:40 PM

Where are you shipping from?

#8 KevvinG

KevvinG
  • LocationMississauga, Ontario, Canada

Posted 21 November 2016 - 12:54 PM

PM'd about some parts!


'77 280Z w/ 3x 40DCOE18


#9 zmnap

zmnap
  • LocationCincinnati

Posted 21 November 2016 - 01:22 PM

PM Sent about the whole car. 



#10 James2785

James2785
  • LocationPhoenix AZ

Posted 21 November 2016 - 01:22 PM

PM sent!


1976 280Z


#11 HecLB

HecLB
  • LocationLos Angeles

Posted 21 November 2016 - 03:44 PM

PM sent



#12 Turbo260Z

Turbo260Z
  • LocationOrlando

Posted 21 November 2016 - 04:42 PM

PM sent on transmission!

#13 Owenbfree

Owenbfree
  • Locationnew jersey

Posted 22 November 2016 - 05:09 AM

Was a blast what happened and why to part out? Im interested in you tuned ecu and maf. DO you have any pictures? 



#14 RS02

RS02
  • LocationHolland MI 49423

Posted 22 November 2016 - 07:08 AM

PM sent about wheels and shocks.



#15 Grnsky

Grnsky
  • LocationSan Diego

Posted 22 November 2016 - 07:40 AM

Pm'd about oil cooler.



#16 Kash

Kash
  • LocationRound Lake Beach, IL

Posted 22 November 2016 - 10:34 AM

Wow! Thanks for the interest...have trouble opening up my PM. Will respond asap.


[SIGPIC][/SIGPIC]
'78 280z 3.1 Stroker, t3/t04E w/JWT Z31 ECU & Cobra MAF, Z32 5 sp, z31 r200 LSD w/CV's, Fidanza Flywheel, 4 Wheel Disc and Power Steering

3.1 Turbo Stroke Build-Up


#17 Kash

Kash
  • LocationRound Lake Beach, IL

Posted 22 November 2016 - 10:48 AM

Will prioritize sale of whole car first.

 

Shipping form 60073 (round Lake Beach, IL)

 

Console has a small unnoticeable crack, the bad part is that I had to make a 3/4 x 1 inch slot around the gear shifter (top) to accommodate the 280zx turbo trans when I had it installed. 

 

Door panels all other interior parts are in great shape.

 

Also have like new steering wheel (not faded and rubber in great condition) - $100

 

"was blast..." you have no idea how badly this hurts :-(   Just happy to know these parts will end up in the right hands on HZ. 


[SIGPIC][/SIGPIC]
'78 280z 3.1 Stroker, t3/t04E w/JWT Z31 ECU & Cobra MAF, Z32 5 sp, z31 r200 LSD w/CV's, Fidanza Flywheel, 4 Wheel Disc and Power Steering

3.1 Turbo Stroke Build-Up


#18 Turbo260Z

Turbo260Z
  • LocationOrlando

Posted 22 November 2016 - 10:56 AM

PM again on whole car

#19 James2785

James2785
  • LocationPhoenix AZ

Posted 22 November 2016 - 11:05 AM

Will prioritize sale of whole car first.

 

Shipping form 60073 (round Lake Beach, IL)

 

Console has a small unnoticeable crack, the bad part is that I had to make a 3/4 x 1 inch slot around the gear shifter (top) to accommodate the 280zx turbo trans when I had it installed. 

 

Door panels all other interior parts are in great shape.

 

Also have like new steering wheel (not faded and rubber in great condition) - $100

 

"was blast..." you have no idea how badly this hurts :-(   Just happy to know these parts will end up in the right hands on HZ. 

 

Since you have offers on the entire car, are the stock turbo manifolds part of this or are they separate loose parts you're trying to get rid of? I need one for my build and have not been able to find any locally.


1976 280Z


#20 Owenbfree

Owenbfree
  • Locationnew jersey

Posted 22 November 2016 - 12:09 PM

James, I have n/a manifolds. I know you probably wouldn't want the intake so much but if your really having trouble the exhaust manifold could be adapted to fit a turbo with some work. 






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users