Gen I & II Chevy V8 Tech Board

8916 topics in this forum

1. Low $ Low Profile Air Cleaners...again

   By BillZ260, February 12, 2008
   • 10 replies
   • 3.6k views
   • 
   • pparaska
   • March 30, 2009

3. Dealer refuses to do Crank position relearn

   By aziza z, February 12, 2008
   • 10 replies
   • 7.4k views
   • 
   • aziza z
   • February 17, 2008

4. Part throttle 2k-2.5k RPM knocking...

   By Shaner, February 11, 2008
   • 10 replies
   • 1.4k views
   • 
   • Shaner
   • April 28, 2008

5. Hydraulic throw out bearings

   By HarrisonTX, February 10, 2008
   • 10 replies
   • 3.3k views
   • 
   • blueovalz
   • February 16, 2008

6. Amp meter’s who runs them? What is the danger?

   By tkach, February 10, 2008
   • 10 replies
   • 1.2k views
   • 
   • ktm
   • February 12, 2008

7. $200 JTR kit on Craigslist...

   By OlderThanMe, February 8, 2008
   • 0 replies
   • 1k views
   • 
   • OlderThanMe
   • February 8, 2008

8. I drove the LT1 swap to work today.

   By deja, February 7, 2008
   • 15 replies
   • 2k views
   • 
   • deja
   • February 7, 2008

9. question about distributors.

   By HICKL, February 6, 2008
   • 10 replies
   • 1.8k views
   • 
   • Corzette
   • February 7, 2008

10. bit of oil pan gasket info

    By grumpyvette, February 5, 2008
    • 11 replies
    • 5.4k views
    • 
    • grumpyvette
    • February 10, 2008

11. Block huggers with an oil cooler

    By Zerrari GTO, February 5, 2008
    • 4 replies
    • 1.2k views
    • 
    • getZ
    • February 7, 2008

12. headers

    By zmann69, February 4, 2008
    • 7 replies
    • 1.8k views
    • 
    • rwwisnesky
    • February 6, 2008

13. fast drag cars 1 2

    By badassbowtie, February 2, 2008
    • 22 replies
    • 4.2k views
    • 
    • Guest
    • February 7, 2008

14. Tko tremac trans W/sbc

    By 78Z/250GTO, February 2, 2008
    • 8 replies
    • 1.8k views
    • 
    • dsommer
    • February 6, 2008

15. cheap t56s?

    By joker120, February 1, 2008
    • 2 replies
    • 1k views
    • 
    • Slammed68
    • February 2, 2008

16. what wiring harness do you use?

    By plexus, January 31, 2008
    • 4 replies
    • 1.5k views
    • 
    • mas8230
    • September 24, 2008

17. lifters leak down?

    By Ferd/289, January 31, 2008
    • 6 replies
    • 2.8k views
    • 
    • grumpyvette
    • February 2, 2008

18. 280zx SBC possible crossmember??

    By z or bust, January 31, 2008
    • 0 replies
    • 678 views
    • 
    • z or bust
    • January 31, 2008

19. 280zx SBC possible crossmember??

    By z or bust, January 31, 2008
    • 0 replies
    • 22 views
    • 
    • z or bust
    • January 31, 2008

20. clutch fork issue

    By stemo76, January 30, 2008
    • 2 replies
    • 1.2k views
    • 
    • stemo76
    • February 4, 2008

21. My Z32 406 project...need help in NC or SC

    By Syndicate, January 29, 2008
    • 17 replies
    • 2.8k views
    • 
    • Syndicate
    • February 5, 2008

22. SBC ready 240Z on craigslist...$800

    By OlderThanMe, January 28, 2008
    • 1 reply
    • 990 views
    • 
    • jbk240z
    • January 29, 2008

23. Hand picking a set of rods. How to.

    By dr_hunt, January 28, 2008
    • 3 replies
    • 895 views
    • 
    • grumpyvette
    • January 28, 2008

24. Which Air Box to use?

    By Turbo Meister, January 28, 2008
    • 18 replies
    • 2.4k views
    • 
    • Turbo Meister
    • January 31, 2008

25. Finally Got it working

    By Hopelessly Confused, January 27, 2008
    • 3 replies
    • 891 views
    • 
    • deja
    • January 27, 2008

26. Short rod 383 ne1 running one

    By gretchen/jason, January 27, 2008
    • 15 replies
    • 2k views
    • 
    • lsdengines
    • February 11, 2008