Jump to content
HybridZ

mrcheeze36

Members
 View Profile  See their activity

  • Posts

    266

  • Joined

  • Last visited

 Content Type 

Everything posted by mrcheeze36

  1. mrcheeze36
    Derek, your valve cover would also look good in red like that...or in a red wrinkle finish too
  2. mrcheeze36
    JeffP's site http://www.angelfire.com/extreme/280zxt/
  3. mrcheeze36
    Please add me to the list for the next run (w/ centering ring)
  4. mrcheeze36
    If a 3.54 with a Torsen, then it's off of an 07'.
  5. mrcheeze36
    Torsen but an 07' is 3.54 and an 08' is a 3.9: http://forums.hybridz.org/topic/38251-complete-differential-list-need-help/?p=681962
  6. mrcheeze36
    If not the LD block I'm guessing a plate like the OS Giken one from their RB 3L kit.
  7. mrcheeze36
    http://www.atlanticz.ca/zclub/techtips/cam/
  8. mrcheeze36
    Has anyone used the reproduction interior pieces from classicdatsun.com? If they are good, that could be another option for getting red interior.
  9. mrcheeze36
    I ordered two Aisin WPN079 water pumps from Rock Auto last month. The impeller diameter for both measured close to 3" like some of the other members.
  10. mrcheeze36
    3.4L http://www.spoolimports.com/spool-stroker-kits/spool-nissan-rb30-stroker-crank-kit 3.2L http://www.spoolimports.com/spool-stroker-kits/spool-rb32-stroker-kit
  11. mrcheeze36
    Here's to link to that thread: http://www.classiczcars.com/forums/engine-drivetrain-s30/42488-new-engine.html Diseazd's engine specs: L28 N42 block bored .040 (he's using an F54 on his 2nd build) L24 crank and rods L28 P79 flat-top pistons 0.040 over (ITM pistons) P79 head shaved and shimmed .080 inches About 9.2 to 1 C/R Isky stage III cam
  12. mrcheeze36
    I don't believe Austin cut into the firewall https://sites.google.com/a/vq240z.com/www/enginemounts
  13. mrcheeze36
    I have taken one out from a 2+2 260Z MT.
  14. mrcheeze36
    I got an R200 3.36 in the past from a 260Z 2+2...MT if remember correctly That one's not covered in the link mentioned a few posts up.
  15. mrcheeze36
    See post number 10: http://forums.hybridz.org/topic/105868-subaru-diff-clarification/?p=1003308 I cover STI diffs from 04' through 08'...not sure about the other years
  16. mrcheeze36
    That would be a 3.7 rear
  17. mrcheeze36
    Check this thread and read from post #205 to around #245 http://forums.hybridz.org/topic/69340-project-vq-is-underway/page-11
  18. mrcheeze36
    Here you go: http://www.kameariusa.com/L6_r200.php Options are 3.154, 4.875, and 5.143. Retail pricing is $1675
  19. mrcheeze36
    Because race car? Lol
  20. mrcheeze36
    Different people claim different spline counts. I have Q45 hubs and 300zxtt axles at home, I'll confirm the count this weekend and will take pics. Here's a thread I found from another 240sx forum (says 30 spline there): http://www.club240.com/forums/showthread.php?t=40461
  21. mrcheeze36
    The Q45/Z32TT are interchangeable between vehicles. They work with either hub.
  22. mrcheeze36
    1 slight correction, the Q45 is a short nose R200. R230s are only from the Z32TT or Armada/QX56. Axles are interchangeable between the Q45 and Z32TT. Q45's Q45/Z32TT hub inside spline count is 32 (post #4 and post #41): http://forums.hybridz.org/index.php?showtopic=35579 Arizona Z car also has a mustache bar that will work with the Q45 diff swap: http://arizonazcar.com/diffmount.html
  23. mrcheeze36
    LOL
  24. mrcheeze36
    Thanks for the responses Mike and Joe
  25. mrcheeze36
    Hi Mike, Where did you get the $1500 quote from? I contacted Robert Hall from The Driven Man in TN (thedrivenman@thedrivenman.com) as he was listed as the US contact on the site and he said the 240Z kit is $1795 + $38 shipping (to CA).
×
×
  • Create New...