Drivetrain

6104 topics in this forum

1. HR31 r200 longnose into 280z with r180

   By intuitdriver, April 21, 2008
   • 4 replies
   • 1.5k views
   • 
   • S30TRBO
   • April 21, 2008

3. 280z stub axle nuts

   By ozzinc, April 21, 2008
   • 10 replies
   • 4.2k views
   • 
   • johnc
   • April 24, 2008

4. Rebuilt a "wide ratio" tranny using 5th gear from a "close ratio"

   By tincup, April 20, 2008
   • 16 replies
   • 3.9k views
   • 
   • gereed75
   • July 26, 2017

5. short r200 and arizonaz brace

   By intuitdriver, April 20, 2008
   • 1 reply
   • 794 views
   • 
   • JMortensen
   • April 20, 2008

6. Back Halved Z almost done

   By zthis, April 20, 2008
   • 4 replies
   • 1.1k views
   • 
   • Mike kZ
   • April 21, 2008

7. Diff drain plug size

   By deja, April 20, 2008
   • 4 replies
   • 1.1k views
   • 
   • deja
   • April 22, 2008

8. LT1 280z tranny questions

   By Geking, April 19, 2008
   • 3 replies
   • 994 views
   • 
   • wheelman
   • April 21, 2008

9. Australian '76 260Z diff, is it R200?

   By Guest rolls, April 18, 2008
   • 1 reply
   • 800 views
   • 
   • Guest
   • April 18, 2008

10. 280ZX AWD Conversion?

    By Guest TwinCam, April 17, 2008
    • 13 replies
    • 4.4k views
    • 
    • DrEaM
    • April 21, 2008

11. Changing input shaft t5

    By mossy74, April 17, 2008
    • 3 replies
    • 1.1k views
    • 
    • dsommer
    • April 18, 2008

12. LSD availability

    By intuitdriver, April 16, 2008
    • 19 replies
    • 2.8k views
    • 
    • JMortensen
    • June 15, 2008

13. r200 gear whine

    By md614, April 16, 2008
    • 1 reply
    • 1k views
    • 
    • JMortensen
    • April 16, 2008

14. T-5 in n/a

    By abes, April 16, 2008
    • 1 reply
    • 688 views
    • 
    • abes
    • April 16, 2008

15. Is the Borg Warner T5 a good trans?

    By cholag, April 16, 2008
    • 6 replies
    • 6.2k views
    • 
    • ben280zx
    • April 17, 2008

16. R180 reassembly question- side flange alignment?

    By Mn_Z_Man, April 15, 2008
    • 0 replies
    • 756 views
    • 
    • Mn_Z_Man
    • April 15, 2008

17. Another Q45 R200 installed

    By Briguy280Z, April 15, 2008
    • 9 replies
    • 6.4k views
    • 
    • Ylo73z
    • May 13, 2014

18. 77 280z drivetrain conversion: driveshaft question

    By intuitdriver, April 14, 2008
    • 1 reply
    • 906 views
    • 
    • intuitdriver
    • April 16, 2008

19. Mustache Bar Bushings... I did something bad...

    By rudypoochris, April 14, 2008
    • 10 replies
    • 3.3k views
    • 
    • Savage42
    • April 14, 2008

20. Thread size for 300zx stub axles?

    By tec280zx, April 13, 2008
    • 2 replies
    • 772 views
    • 
    • tec280zx
    • April 13, 2008

21. R180 snapin half shafts

    By ASA240Z, April 12, 2008
    • 3 replies
    • 1.4k views
    • 
    • zcarnut
    • July 1, 2008

22. ACT pressure plate, which is this one?

    By 1 fast z, April 9, 2008
    • 0 replies
    • 658 views
    • 
    • 1 fast z
    • April 9, 2008

23. T-5 differences?

    By Guest bippu Z, April 8, 2008
    • 6 replies
    • 1.2k views
    • 
    • BillZ260
    • April 9, 2008

24. home stretch-my q45 diff!

    By 1 tuff z, April 8, 2008
    • 12 replies
    • 1.8k views
    • 
    • 1 tuff z
    • April 17, 2008

25. clutch master cylinder rod

    By Guest RagedApe, April 7, 2008
    • 2 replies
    • 677 views
    • 
    • Guest
    • April 7, 2008

26. q45 fluid help

    By 1 tuff z, April 5, 2008
    • 1 reply
    • 750 views
    • 
    • SATAN
    • April 6, 2008