MegaSquirt

1996 topics in this forum

1. Considering Megasquirt? LOOK HERE!!!! 1 2

   By Guest bastaad525, November 12, 2004
   • 27 replies
   • 8.2k views
   • 
   • Guest
   • November 23, 2004

3. Controling boost

   By zane9000, July 12, 2006
   • 11 replies
   • 1.3k views
   • 
   • zane9000
   • July 30, 2006

4. Controller wont connect

   By boosted280, November 6, 2010
   • 5 replies
   • 1.8k views
   • 
   • Hardwyre
   • January 9, 2011

5. Controlling electric exhaust cutout with MS?

   By Challenger, October 9, 2011
   • 1 reply
   • 1.3k views
   • 
   • BLOZ UP
   • October 9, 2011

6. convert a N/A 1981 280ZX to megasquirt

   By JanspeedZ, July 14, 2011
   • 13 replies
   • 5.1k views
   • 
   • akeboshi
   • September 1, 2011

7. Converting Low Impedance Injectors

   By zane9000, April 13, 2006
   • 3 replies
   • 1.7k views
   • 
   • z-ya
   • April 13, 2006

8. Coolant Fan on X2

   By envmyz, July 10, 2005
   • 1 reply
   • 1.1k views
   • 
   • randy 77zt
   • July 11, 2005

9. coolant temp read % not temp

   By MaTTSuN, June 5, 2013
   • 2 replies
   • 760 views
   • 
   • MaTTSuN
   • June 10, 2013

10. Coolant temp sensor vs Cylinder Head temp sensor

    By Thumper, November 8, 2005
    • 1 reply
    • 4k views
    • 
    • Tony D
    • November 8, 2005

11. COP charge time (Please Verify)

    By Nismo280zEd, November 10, 2009
    • 3 replies
    • 1.1k views
    • 
    • Nismo280zEd
    • November 12, 2009

12. COP with Turbo distributor

    By HB280ZT, April 14, 2009
    • 3 replies
    • 1.5k views
    • 
    • slown280z
    • July 12, 2009

13. Corrected wiring diagrams for EDIS-6 ignition module

    By HizAndHerz, May 29, 2007
    • 14 replies
    • 327.5k views
    • 
    • HizAndHerz
    • March 8, 2011

14. Corrupting Firmware...possible problem

    By cygnusx1, August 26, 2007
    • 0 replies
    • 1k views
    • 
    • cygnusx1
    • August 26, 2007

15. cost of ITB EFI compared to webers

    By TheNeedForZ, August 16, 2005
    • 0 replies
    • 1.1k views
    • 
    • TheNeedForZ
    • August 16, 2005

16. Could somebody review this please? I can't idle past 200

    By Watson, April 10, 2014
    • 6 replies
    • 1k views
    • 
    • Watson
    • April 11, 2014

17. Crane firewires good or bad?

    By kvansic162, March 11, 2007
    • 3 replies
    • 842 views
    • 
    • kvansic162
    • March 13, 2007

18. Crank angle sensing 1 2 3

    By cygnusx1, July 28, 2008
    • 56 replies
    • 11.1k views
    • 
    • LanceVance
    • October 8, 2010

19. Crank Angle Sensor Idea

    By Nismo280zEd, August 24, 2008
    • 6 replies
    • 2.6k views
    • 
    • ZXT_bean
    • August 25, 2008

20. Crank angle sensor on z31

    By Guest alex86a2t, July 22, 2006
    • 3 replies
    • 2.2k views
    • 
    • BLOZ UP
    • July 25, 2006

21. Crank Sensor Signal dropping out

    By zack_280, October 4, 2011
    • 2 replies
    • 2.4k views
    • 
    • zack_280
    • October 4, 2011

22. Crank trigger question 1 2

    By dizzle, May 15, 2008
    • 20 replies
    • 3.2k views
    • 
    • kiwi303
    • November 15, 2009

23. Cranking Advance?

    By Flexicoker, March 13, 2009
    • 2 replies
    • 1.9k views
    • 
    • WizardBlack
    • March 28, 2009

24. Cranking pules width

    By zane9000, June 22, 2006
    • 4 replies
    • 898 views
    • 
    • zane9000
    • June 24, 2006

25. Cranking pulse width settings

    By Kali, May 9, 2011
    • 4 replies
    • 1.8k views
    • 
    • Kali
    • May 18, 2011

26. Cranking Pulsewidths

    By BLOZ UP, December 13, 2009
    • 2 replies
    • 949 views
    • 
    • BLOZ UP
    • December 13, 2009