MegaSquirt

1999 topics in this forum

1. Megasquit II 3.57 Can Enabled injectors staying open

   By motomanmike, September 23, 2012
   • 9 replies
   • 2.7k views
   • 
   • Matt Cramer
   • October 8, 2012

3. Need Help with wiring

   By JacobsZ, September 29, 2012
   • 3 replies
   • 1.2k views
   • 
   • motomanmike
   • October 6, 2012

4. It finally runs! MS1 V3.0, MSnS

   By OhBilly, October 3, 2012
   • 2 replies
   • 1.2k views
   • 
   • OhBilly
   • October 3, 2012

5. my edis setup 1 2

   By akeboshi, September 29, 2011
   • 26 replies
   • 8.8k views
   • 
   • Lazeum
   • September 19, 2012

6. Ms 1 v2.2 Help!

   By Nelatl, August 16, 2012
   • 6 replies
   • 1.5k views
   • 
   • kaito
   • September 9, 2012

7. looking for help fixing MS1 problem

   By AkRev, September 4, 2012
   • 7 replies
   • 1.5k views
   • 
   • AkRev
   • September 5, 2012

8. MS-I on l28et

   By JacobsZ, September 1, 2012
   • 5 replies
   • 2.7k views
   • 
   • s30red240z
   • September 3, 2012

9. New tech article: MegaSquirt Acceleration Enrichment Tuning

   By Matt Cramer, August 28, 2012
   • 3 replies
   • 3k views
   • 
   • DCZ
   • August 31, 2012

10. MS3 on 280zx stopped working

    By phi135, August 26, 2012
    • 2 replies
    • 1.2k views
    • 
    • dexter72
    • August 26, 2012

11. Jeep Pencil coils MS2

    By MaTTSuN, August 21, 2012
    • 1 reply
    • 912 views
    • 
    • Matt Cramer
    • August 21, 2012

12. Driving the tach with coil packs

    By letitsnow, June 14, 2012
    • 9 replies
    • 2.9k views
    • 
    • Dan_Austin
    • August 21, 2012

13. Who'd be interested if we made a L28ET trigger wheel? 1 2 3 4 9

    By Matt Cramer, October 21, 2011
    • 161 replies
    • 30.8k views
    • 
    • s30red240z
    • August 17, 2012

14. My IACV solution

    By adam78280z, August 13, 2012
    • 3 replies
    • 1.2k views
    • 
    • Leon
    • August 14, 2012

15. RS232TO USB onboard conversion question

    By macambra, December 3, 2011
    • 7 replies
    • 2k views
    • 
    • BLOZ UP
    • August 9, 2012

16. First L6 sequencer install?

    By Dan_Austin, June 24, 2012
    • 6 replies
    • 1.8k views
    • 
    • Dan_Austin
    • August 3, 2012

17. New MS Install Running Rough

    By Challenger, April 25, 2012
    • 14 replies
    • 3.8k views
    • 
    • Xnke
    • July 31, 2012

18. DIY CAS for L28ET angle settings 1 2

    By macambra, June 4, 2012
    • 26 replies
    • 8.8k views
    • 
    • SleeperZ
    • June 26, 2012

19. Wiring with Bosch 7 Pin Module

    By PITA_Z, June 25, 2012
    • 1 reply
    • 2.5k views
    • 
    • NewZed
    • June 25, 2012

20. Trying to swap a ’83 l28et distributor into a ’75 l28e to drive signal to my MS3 w/ MS3X.

    By Madovic, June 13, 2012
    • 12 replies
    • 1.2k views
    • 
    • SleeperZ
    • June 18, 2012

21. New tech article - understanding the different MS variants

    By Matt Cramer, June 14, 2012
    • 2 replies
    • 1.2k views
    • 
    • duragg
    • June 18, 2012

22. Help me! Megasquirt 2.2 Board Fuel Only 1 2

    By 78zstyle, April 26, 2012
    • 25 replies
    • 3.8k views
    • 
    • 78zstyle
    • June 10, 2012

23. Ms1 misc o2 sensor

    By 1973240, May 26, 2012
    • 4 replies
    • 1.5k views
    • 
    • 1973240
    • June 8, 2012

24. Start then stop

    By MaTTSuN, May 30, 2012
    • 8 replies
    • 1.6k views
    • 
    • MaTTSuN
    • June 5, 2012

25. Post Dyno Compression Test

    By BLOZ UP, May 26, 2012
    • 7 replies
    • 1.7k views
    • 
    • BLOZ UP
    • June 4, 2012

26. Dash Comp Output Channels Not Configured? Tuner Studio

    By Challenger, May 9, 2012
    • 3 replies
    • 1.6k views
    • 
    • Challenger
    • May 18, 2012