MegaSquirt

2000 topics in this forum

1. Idle Control

   By Nismo280zEd, January 28, 2006
   • 5 replies
   • 1.2k views
   • 
   • Metro
   • January 30, 2006

3. Planning MS install and wiring.

   By cygnusx1, March 14, 2007
   • 2 replies
   • 1.2k views
   • 
   • z-ya
   • March 14, 2007

4. MS v3.0 wiring w/ MSD - step 50a or 50b?

   By trwebb26, August 16, 2006
   • 4 replies
   • 1.2k views
   • 
   • trwebb26
   • August 16, 2006

5. Readings on AEM UEGO display vs. MSnS signal don't agree, ideas?

   By Slow_Old_Car, May 7, 2008
   • 5 replies
   • 1.2k views
   • 
   • Slow_Old_Car
   • May 8, 2008

6. Fuel pump not working off relay board

   By Organdonor, October 18, 2008
   • 2 replies
   • 1.2k views
   • 
   • Organdonor
   • October 21, 2008

7. questions about first MS install

   By mattb3562, May 19, 2013
   • 6 replies
   • 1.2k views
   • 
   • mattb3562
   • May 20, 2013

8. MS Wiring

   By HB280ZT, March 2, 2006
   • 6 replies
   • 1.2k views
   • 
   • HB280ZT
   • March 4, 2006

9. ms1 will not flash

   By driftz240, February 8, 2008
   • 4 replies
   • 1.2k views
   • 
   • Matt Cramer
   • February 11, 2008

10. coil igniters

    By onefast87, February 26, 2009
    • 4 replies
    • 1.2k views
    • 
    • Brad-ManQ45
    • February 28, 2009

11. Tuning Problems

    By badjuju, June 22, 2006
    • 5 replies
    • 1.2k views
    • 
    • mobythevan
    • June 23, 2006

12. rpm pot

    By Nismo280zEd, September 29, 2008
    • 5 replies
    • 1.2k views
    • 
    • Nismo280zEd
    • October 1, 2008

13. Some questions with the '81 CAS and MSnS-extra

    By Metro, October 28, 2005
    • 5 replies
    • 1.2k views
    • 
    • Metro
    • November 2, 2005

14. ignition stumble at 2200rpm

    By bigblock502, March 4, 2010
    • 3 replies
    • 1.2k views
    • 
    • bigblock502
    • March 4, 2010

15. MSnS extra .. starts and runs for 2 sec. then dies! Then starts right up fine!

    By proxlamus©, September 14, 2005
    • 5 replies
    • 1.2k views
    • 
    • envmyz
    • September 16, 2005

16. HEI module necessary for V3 pcb?

    By olie05, September 1, 2006
    • 4 replies
    • 1.2k views
    • 
    • mobythevan
    • September 3, 2006

17. EDIS Trigger position

    By Noddle, August 27, 2008
    • 4 replies
    • 1.2k views
    • 
    • Noddle
    • August 29, 2008

18. question about 1/4 volt 1k resistor

    By jt79zxt, July 14, 2010
    • 4 replies
    • 1.2k views
    • 
    • jacob80
    • July 15, 2010

19. Happy camper!

    By Adimir, May 30, 2011
    • 3 replies
    • 1.2k views
    • 
    • cygnusx1
    • June 2, 2011

20. Look at my trigger log

    By Dadaluma, January 9, 2012
    • 5 replies
    • 1.2k views
    • 
    • kaito
    • January 11, 2012

21. N/A 280z Tuning

    By trwebb26, June 3, 2006
    • 1 reply
    • 1.2k views
    • 
    • mobythevan
    • June 5, 2006

22. Upcoming MSnS projects (hemi...)

    By mobythevan, February 23, 2006
    • 4 replies
    • 1.2k views
    • 
    • mobythevan
    • February 24, 2006

23. finally got my z started w/o much trouble

    By 260zturbo, March 3, 2007
    • 6 replies
    • 1.2k views
    • 
    • 260zturbo
    • March 4, 2007

24. trigger inverted?

    By evildky, August 8, 2008
    • 5 replies
    • 1.2k views
    • 
    • mobythevan
    • August 8, 2008

25. Trying to swap a ’83 l28et distributor into a ’75 l28e to drive signal to my MS3 w/ MS3X.

    By Madovic, June 13, 2012
    • 12 replies
    • 1.2k views
    • 
    • SleeperZ
    • June 18, 2012

26. getting a constant 10 v to the ignition?

    By midnightzxt, April 24, 2005
    • 8 replies
    • 1.2k views
    • 
    • mobythevan
    • April 26, 2005