Nissan L6 Forum

6893 topics in this forum

1. P90A Hydraulic Lifter Rebuilding

   By m1ghtymaxXx, May 5, 2010
   • 1 reply
   • 3.1k views
   • 
   • paul vixie
   • July 14, 2010

3. install headers/ problems with idle-power

   By punkmilhouse, July 13, 2010
   • 5 replies
   • 1.1k views
   • 
   • punkmilhouse
   • July 13, 2010

4. putting p90head on a 75 280z Block 1 2 3

   By 280zbeeT, June 23, 2010
   • 47 replies
   • 6.8k views
   • 
   • 280zbeeT
   • July 13, 2010

5. Cracks in cylinder head

   By awoz87, July 12, 2010
   • 4 replies
   • 1k views
   • 
   • BRAAP
   • July 13, 2010

6. Camshaft lubrication question..

   By tightywhitey185, July 13, 2010
   • 0 replies
   • 850 views
   • 
   • tightywhitey185
   • July 13, 2010

7. Engine noise on decell.

   By burninator, July 12, 2010
   • 2 replies
   • 773 views
   • 
   • burninator
   • July 12, 2010

8. Location of MSD 6A

   By 240zip, July 8, 2010
   • 5 replies
   • 1.2k views
   • 
   • BluDestiny
   • July 12, 2010

9. Do I balance these rods or not?

   By 2eighTZ4me, June 25, 2010
   • 9 replies
   • 2.1k views
   • 
   • SHADY280
   • July 10, 2010

10. The plan for my engine freshening

    By trwebb26, June 29, 2010
    • 2 replies
    • 1.2k views
    • 
    • k1evo2
    • July 10, 2010

11. Preparing 78 280z for Turbo Swap, Reusing stock block 1 2

    By Challenger, June 30, 2010
    • 21 replies
    • 3.8k views
    • 
    • Challenger
    • July 7, 2010

12. 240z Camshft oiler tube gaskets

    By ciavola, July 4, 2010
    • 8 replies
    • 2.2k views
    • 
    • Tony D
    • July 5, 2010

13. L28ET into a 71 240z

    By Manniacz, February 25, 2010
    • 10 replies
    • 4.1k views
    • 
    • ZPIT U OUT
    • July 4, 2010

14. Do I need rear main seal sleeve or not?

    By ciavola, July 3, 2010
    • 1 reply
    • 899 views
    • 
    • Tony D
    • July 3, 2010

15. rear main seal

    By ciavola, July 2, 2010
    • 1 reply
    • 763 views
    • 
    • steve260z
    • July 3, 2010

16. Thicker Head Gasket Recommendations Please

    By WindyCityZnut, June 26, 2010
    • 13 replies
    • 3.8k views
    • 
    • Tony D
    • July 2, 2010

17. Valve Cover Tightening Sequence

    By 10cjennings, July 1, 2010
    • 5 replies
    • 3.4k views
    • 
    • 10cjennings
    • July 2, 2010

18. Is my cam timing okay?

    By tightywhitey185, July 1, 2010
    • 4 replies
    • 1.1k views
    • 
    • RTz
    • July 2, 2010

19. Revcounter on a 1983 R 30 skyline

    By datsun L fan, July 1, 2010
    • 1 reply
    • 776 views
    • 
    • Noddle
    • July 2, 2010

20. Was running fine on 6 cylinders...

    By csm240z, June 28, 2010
    • 6 replies
    • 1.1k views
    • 
    • woldson
    • July 1, 2010

21. power to fuel pump changes when plugged in

    By rhettro74, June 30, 2010
    • 0 replies
    • 711 views
    • 
    • rhettro74
    • June 30, 2010

22. Valve Cover Bolt Sizes

    By 10cjennings, June 29, 2010
    • 5 replies
    • 5.3k views
    • 
    • junglist
    • June 30, 2010

23. Help Please: Removing Rocker Arms, Afraid of Dropping a Valve into Motor

    By dano, June 9, 2010
    • 3 replies
    • 1k views
    • 
    • dano
    • June 27, 2010

24. Valve cover breather baffle sealant

    By rossman, June 25, 2010
    • 3 replies
    • 1.1k views
    • 
    • rossman
    • June 27, 2010

25. Timing cover bolts, what grade?

    By ciavola, June 27, 2010
    • 1 reply
    • 705 views
    • 
    • Tony D
    • June 27, 2010

26. 78 280z stock engine mystery please help!!!

    By Jeff 78 280z, June 25, 2010
    • 8 replies
    • 4.1k views
    • 
    • Tony D
    • June 27, 2010