Evan Purple240zt

Bondo won't stick to your dash very well, I think a urathane based product would be better. Evan

Guys, I am going to be re-dying my whole interior when it gets warm enough. What brand dye/paint did you use? I am NOT doing a color change, my interior has sun fade. Evan

The sentra guys got all bent outta shape about it too LOL.

6boost out of austrailia(sp). There was a group buy on nico on these. Evan

Stony ,I have a greddy a/f gauge like that. How does it work? I have no manual and am not sure. There are some dials and buttons on the datalink box too. Looks good! Thanks - Evan

If your tech class does not have a timing light you need to donate some money to the school LOL. Good luck dude.

Ultra or Prime No idea on value, the are kinda common I think.

You can also speak to local lumber yards, I am sure they could refer you to someone who can set you up. Hickory cabinets? NICE Evan

Did you pull the sparkplug to make sure its not defective? Pull your cap and make sure there are no carbon tracks anywhere to indicate a bad cap/rotor. Evan

Could you guys use bronze? I had really good luck ordering bronze bearings in metric sizes from a place online. I can look it up if anyone thinks it could work. Not sure, it may be too soft I am thinking. Just throwing it out there. Evan

I had a countertop that had a wood face with a formica top, it looked really sharp! Good luck! i want to see pics when you are done, sounds like quite the project.

David, don't get all bent out of shape over what I said, sorry if I pissed you off or incinuated(sp?) that you would not send her to a good home. I want your pup to go to a good home too. Pretty dog BTW. Evan

^ you and me both pal ^ LOL. At work, when there is nothing going on I surf constantly. Realistically I check hybridz no less often then every 1/2 hour during the week. I am expected to keep machines running, customers happy, and parts rebuilt. When things are going well, I surf alot. When the $hi* hits the fan, I may end up working 12 hours straight. I think it averages out really.. My problem at home is there is not much to do. I love music, but my main system is in my living room with the TV. I have taken up building electronics stuff to keep me occupied when indoors during the winter. It does help, but I still surf a TON. Evan

First, you cannot post pets on craigslist. Its against the policy and they will flag it down. Be VERY picky about who adopts your dog, do your homework. It would my worst nightmare that someone who would abuse or do anything bad to/with your pup. Evan Sorry I know this post isn't too helpful. But thats the stuff that runs through my mind when I see pets posted up.

If this is the stuff that I think it is, its a thin rubbery coating. Cover your interior pieces with fabric is the best way to go IMO.

Phil, before you put those injectors on your car send them out for flow testing. I have venoms and the first set I got were bad, car ran terrible. I am going to have deatchwerks flow test these before I hit the dyno. The warranty service was great, they sent me a new set no questions asked. Evan

I have a zeitronix ZT2 wide band setup in my car. I also have a greddy narrowband air fuel gauge with a four wire sensor. I want to connect the narrowband output (the output that would normally run to the ECU) to the greddy gauge so I have some idea of whats going on A/F wise. I have found which wires in the harness were for the power/ground of the 02 signal. I am not sure which is which... I attempted to connect it to my output of my ZT2 and was getting a reading of rich (where my laptop said it was fine). Could this be because I was NOT using shielded wire to connect the zt2 to the gauge? When I hold the two O2 wires in my fingers, I can make the gauge bounce. That leads me to think I have selected the right wires for that. I also know which wires I need to use to connect the zt2. Narrowband out. This leaves me with one wire left over from the ground for the O2 sensor. Should this be grounded with the wideband? It really does not seem to be working, I was wondering if anyone else had attempted this. Thanks - Evan

Thanks Luigi!

Phil, I wonder if you are feeling more HP or faster spool. Either way, cool. Evan BTW, who cares how much TQ you have at 2k when you have plenty up top!! I don't think it will hurt driveability at all.

Not a bad fit. Two thumbs up for supra-sized exhausts.

Sorry I guess I was not direct enough when I said this stuff is definitely not the same as suede. It will look good on accents, but not something I would want everywhere. Like I said, I imagine that corvette dash is pretty ugly LOL. Let us know what you find, I suspect that you will end up having someone do it in real suede. Evan

I ran across this thread as I watched 4x4 on spike and they put that motor in a samurai. It runs on veggie oil. Seems pretty cool. Evan

I would stick a known good motor in it and go. Thats a good deal IMO provided there is no problem with the transfer case etc.. Everyone makes a huge deal about crank walk, but if you don't run a super stiff clutch and your not trying to make big HP numbers you probably won't have any trouble with it.

dude that is a killer deal! Nice score! Evan

God I hear ya LOL. Evan