Search the Community
Showing results for tags 't5'.
Found 14 results
-
Trying to put all parts into a 71' 240z. I am looking at running a l28et with a t5 out of a 280zx turbo and then an r200 diff out of a 280z, will I need to modify the trans mounts to run the t5 still? Also will I want the driveshaft out of the 280z or the 280zx turbo? I am trying to setup something with the least amount of fabrication required. -
Hey guys looking for the Green Plastic 6 tooth speedo main drive gear, 1.13 inches ID and 1.73 inches OD from a 1983 Turbo Borg Warner Transmission. Any help is greatly appreciated. Please PM me if you have one!
-
Will the Laine Family sbf write-up work for a 351W?
amuscato77 posted a topic in Ford V8Z Tech Board
This has probably been touched upon in another post but I have been searching for hours and can't find anything. I just picked up a donor fox body with a 5.8L 351W in it mated to a WC T5. I originally wanted to do just a 5.0 out of a fox but the price was too good to pass up on this car. Has anyone used the Laine Family Write up to do this swap? Does the engine cradle work for it as well as the mounting positions? :bang head: Sorry if this is asking a lot my fabrication skill and tool selection is not exactly what I would like it to be for this project so any help would be greatly appreciated I imagine the driveshaft length should be about the same correct me if I'm wrong but yeah even if you guys just link a thread that has the info I'm just a helpless newbie so I'd be very greatful P.S. I plan on boosting this 351w eventually just to change it up a bit even more for the sbf Z-world -
Hi, I'm looking at a driveshaft I found and based on the pictures it looks like a T5 driveshaft that's been cut and shortened on one end. To my knowledge, they're the only ones that neck down at both ends, but this one only has that at one. It also has the square diff flange and seems to have a 26 spline tailshaft yoke based on the blurry picture I got. Can anyone tell me for sure that it is/isn't? Thanks.
-
I'm looking for a 280ZXT manual transmission crossmember. Looks similar to the normal 280ZX transmission crossmember but I think it bumps out a little horizontally instead of just being the straight U shape.
-
Like it says, I want to buy a good, working T5 manual transmission out of an 82-83 280ZX turbo, and would also LOVE it if the properly modified driveshaft to fit a 240Z came with it! I have been looking for a while so I will offer +$500 (shipped or delivered to Reno area) to make this happen (more if it is in really good shape). Also, looking for a Limited Slip Differential. An R200 with the non-finned cover to fit a 240Z would be great. An R180 out of an STi with the half-shafts to fit a 240Z would be SUPER and I will pay top dollar for either. Let me know what you have!! (image used for reference, shamelessly stolen from datsunzgarage.com)
-
looking for drive shaft for 5speed T5 transmission.
-
I was hoping to get help from some knowledgeable forum members I'm currently restoring my 78 z I did a L28et swap with a T5 Transmission I've been looking for a T5 driveshaft to shorten it to fit my Z I recently found one for sale but the picture he has of the driveshaft looks tinner from what I've seen from other T5's. This is where I need some help recognizing the driveshaft from the one i want to buy and from the one I've seen classified as a T5 driveshaft. Thanks guys in advance. The driveshaft I want to buy. The T5 driveshaft I've seen for sale. Notice the difference one looks thicker.
-
Put the trans and motor together before I clean them up a little
BubbaDog127 posted a gallery image in Members Albums
From the album: Cobra 5.0 280z
-
From the album: Cobra 5.0 280z
Brian Laine aka motormatch cradle kit for a small block ford -
From the album: Cobra 5.0 280z
Brian Laine aka motormatch cradle kit for a small block ford -
I have a 83 280zx turbo with the Borg Warner T5. Ive considered the routes of putting in a wc t5 (too much customization), going the nissan 5 speed route (rather not), and just going to the junkyard and getting a t5 out of another 280zx (i feel safer knowing i have a freshly rebuilt one). Story: My 3-4 syncro assembly is bad. When driving home it got harder and harder to shift into 3rd and any gear for that matter. I got home driving in 1st down my street. Then when i stopped the car and put it into neutral, all i heard was a clicking clacking sound as the car was sitting in neutral. I stepped on the clutch and the sound disappeared. It would come back as i eased off the clutch then finally it somehow slapped into gear(the noise also stopped) though the shifter was in neutral and i quickly pressed back down on the clutch. I eased off the clutch again to learn the car was in gear and i couldn't get it out. I took apart the transmission to find that the part that is supposed to slide around over the 3/4 syncro was hard to budge. after some very manly hours i was able to push it loose. I lifted the keys and saw some metal shavings inside and it was really difficult to press in the keys and slide the part around. now that the transmission itself was in neutral i rotated the shafts to see if the transmission was in neutral and it was until it would randomly grab into gear and let go. I checked the gears rotation ratios and determined it to be 3/4. Symptoms: Noise from Transmission Car hard to shift Transmission suddenly goes into a gear Cant get car out of gear Shifter still in neutral Theory This appears to me that the noise was possibly the keys having trouble going into gear. The car got into 3rd and was hard to shift out because the syncros are bad. It randomly went into gear as performed when turning the shafts in neutral. Shifter was in neutral meaning the forks held the parts in the neutral position but the gears were still in 3rd which could be explained by the spin test aswell since the gears were in that position and it would randomly grab into gear. Solution And Question: Will this rebuild kit work for our (nissan) T5? i posted a question to the seller as well but it says he is away till august..... The brand for the item is Tremec and as most of you would know is the company that took over the T5 from Borg Warner. This kit goes for pretty cheap compared to my googling of syncro assemblies. Any suggestions are welcomed except those saying "just go with nissan 5speed, or get a mustang t5 or any of that" Suggestions should be on the line of "you should buy from here it's cheaper and better" or "i dont think that is your problem, your problem actually is....". I havent seen many topics on rebuild kits (i seen a few but they target one seller that sells a rebuild kit for $250... which is pretty hefty. http://www.ebay.com/itm/T5-NON-WORLD-Class-Master-Rebuild-Kit-GM-Ford-Jeep-AMC-/350712906441#vi-content
-
Looking for a 280ZX Turbo NWC T5 transmission. Willing to pick up within 150 miles of Santa Barbara CA. Must be in good condition. It will be used for road racing.
-
I purchased this from a guy that said it was out of a Camaro. It has a strange bolt patern that does not match the bell housing I have. It looks like a V6 pattern with V8 splines. I'm so confused. I tab with the i.d. number was illegible. Any input whould be appreciated. Thanks, Mike
